Sharp AR-FX12 (serv.man7) Service Manual ▷ View online
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-1
[6] SIMULATIONS, FAX SOFTWARE SWITCH
1. Entering the simulation mode
a. Normal mode
Enter the copy mode and perform the following procedures.
[P]
[*]
[C]
[*]
[Main
code]
[START]
[Sub
code]
[START]
b. FAX mode
Enter the copy mode and perform the following procedures.
[9]
[9]
[*]
[8]
[#]
[7]
2. Switching the simulation mode
Press [USER SETTING] to return to the code entry screen.
3. Canceling the simulation mode
Press CA key to cancel the simulation mode.
4. Simulation list
Code
Function (Content)
Purpose
Section
Item
Main Sub
22
5
Used to check the ROM version of each unit (section).
Other
Software
6
Used to print the list of adjustments and setup data
(simulations, FAX soft switches, counters).
(simulations, FAX soft switches, counters).
Adjustment, setup,
operation data output,
check (print)
operation data output,
check (print)
Data
Setup,
adjustment
data
adjustment
data
11
Used to check the use frequency of FAX. (send/receive)
(Only when FAX is installed.)
(Only when FAX is installed.)
Adjustment, setup,
operation data output,
check (display)
operation data output,
check (display)
FAX
Data
23
2
Jam/Trouble data print
24
10
Used to clear the FAX counter. (After completion of
maintenance, this counter must be cleared.)
(Only when FAX is installed.)
maintenance, this counter must be cleared.)
(Only when FAX is installed.)
Data clear
FAX
Counter
46
12
Used to adjust the print density in the FAX mode (all modes).
An adjustment with this simulation affects all the copy density
adjustment values. (Only when FAX is installed)
An adjustment with this simulation affects all the copy density
adjustment values. (Only when FAX is installed)
Adjustment
Picture
quality
quality
13
Used to adjust the print density in the FAX mode
(Standard mode). (Only when FAX is installed.)
(Standard mode). (Only when FAX is installed.)
Adjustment
Picture
quality
quality
14
Used to adjust the print density in the FAX mode
(Fine mode). (Only when FAX is installed.)
(Fine mode). (Only when FAX is installed.)
Adjustment
Picture
quality
quality
15
Used to adjust the print density in the FAX mode
(Super Fine mode). (Only when FAX is installed.)
(Super Fine mode). (Only when FAX is installed.)
Adjustment
Picture
quality
quality
16
Used to adjust the print density in the FAX mode
(Ultra Fine mode). (Only when FAX is installed.)
(Ultra Fine mode). (Only when FAX is installed.)
Adjustment
Picture
quality
quality
56
1
Data transfer
61
3
Used to adjust laser power (absolute value) in the FAX
reception mode. (Only when FAX is installed.)
reception mode. (Only when FAX is installed.)
Adjustment
Operation
[06]SIMULATIONS ・ FAXSOFTWARESWITCH.fm 1 ページ 2004年12月15日 水曜日 午後2時21分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-2
66
1
Used to set the FAX soft switch function. (Used to utilize the
FAX soft switch function.)
FAX soft switch function.)
Setup
FAX
2
Used to set the FAX soft switch setup to the default.
(Except for the adjustment values)
(Except for the adjustment values)
Data clear
FAX
Data
3
Used to check the operations of FAX PWB memory
(read/write). (This adjustment is required when replacing the
PWB with a new one.)
(read/write). (This adjustment is required when replacing the
PWB with a new one.)
Operation test, check
FAX
Data
4
Used to check the operations of data signal output in the FAX
data output mode.
(Used to check the MODEM operation.)
Send level Max. (Only when FAX is installed.)
data output mode.
(Used to check the MODEM operation.)
Send level Max. (Only when FAX is installed.)
Operation test, check
FAX
Operation
5
Used to check the operations of data signal output in the FAX
data output mode.
(Used to check the MODEM operation.)Signals are sent in the
send level set with the soft switch. (Only when FAX is installed.)
data output mode.
(Used to check the MODEM operation.)Signals are sent in the
send level set with the soft switch. (Only when FAX is installed.)
Operation test, check
FAX
Operation
6
Used to print the confidential password.
(Used when the confidential password is forgotten.)
(Only when FAX is installed.)
(Used when the confidential password is forgotten.)
(Only when FAX is installed.)
User data output, check
(display, print)
(display, print)
FAX
Data
7
Used to print the image memory data (memory send, receive).
(Only when FAX is installed.)
(Only when FAX is installed.)
User data output, check
(display, print)
(display, print)
FAX
Data
8
Used to check the output operation of the FAX sound signals.
(Sound output IC operation check) Send level Max.
(Only when FAX is installed.)
(Sound output IC operation check) Send level Max.
(Only when FAX is installed.)
Operation test, check
FAX
Operation
9
Used to check the output operation of the FAX sound signals.
(Sound output IC operation check)
(Only when FAX is installed.)
(Sound output IC operation check)
(Only when FAX is installed.)
Operation test, check
FAX
Operation
10
Used to clear all data of image memory
(memory send, receive). Confidential data are also cleared.
(Only when FAX is installed.)
(memory send, receive). Confidential data are also cleared.
(Only when FAX is installed.)
User data output, check
(display, print)
(display, print)
FAX
Data
11
Used to check the output operation of FAX G3 mode 300BPS.
(Used to check the MODEM operation.)
Send level 0dB (Max.) (Only when FAX is installed.)
(Used to check the MODEM operation.)
Send level 0dB (Max.) (Only when FAX is installed.)
Operation test, check
FAX
Operation
12
Used to check the output operation of FAX G3 mode 300BPS.
(Used to check the MODEM operation.) Signals are sent in the
send level set with the soft switch. (Only when FAX is installed.)
(Used to check the MODEM operation.) Signals are sent in the
send level set with the soft switch. (Only when FAX is installed.)
Operation test, check
FAX
Operation
13
Used to enter (set) the number for the FAX dial signal output
test.
(The dial number signal set with this simulation is outputted in
the dial signal output test with SIM 66-14~16)
(Only when FAX is installed.)
test.
(The dial number signal set with this simulation is outputted in
the dial signal output test with SIM 66-14~16)
(Only when FAX is installed.)
Setup
FAX
Data
14
Used to set the make time in the FAX pulse dial mode (10PPS)
and to test the dial signal output.
(The dial number signal set with SIM 66-13 is outputted.)
Used to check dialing troubles and the operation.
(Only when FAX is installed.)
and to test the dial signal output.
(The dial number signal set with SIM 66-13 is outputted.)
Used to check dialing troubles and the operation.
(Only when FAX is installed.)
Setup
FAX
Operation
15
Used to set the make time in the FAX pulse dial mode (20PPS)
and to test the dial signal output. (The dial number signal set
with SIM 66-13 is outputted.) Used to check dialing troubles
and the operation. (Only when FAX is installed.)
and to test the dial signal output. (The dial number signal set
with SIM 66-13 is outputted.) Used to check dialing troubles
and the operation. (Only when FAX is installed.)
Setup
FAX
Operation
16
Used to test the dial signal (DTMF) output in the FAX tone dial
mode. (The dial number signal set with SIM 66-13 is outputted.)
The send level can be set to an optional level.
Dialing troubles and operation.(Only when FAX is installed.)
mode. (The dial number signal set with SIM 66-13 is outputted.)
The send level can be set to an optional level.
Dialing troubles and operation.(Only when FAX is installed.)
Setup
FAX
Operation
17
Used to test the dial signal (DTMF) output in the Fax tone dial
mode. Send level Max. Used to check the operation.
(Only when FAX is installed.)
mode. Send level Max. Used to check the operation.
(Only when FAX is installed.)
Setup
FAX
Operation
18
Used to test the dial signal (DTMF) in the FAX tone dial mode.
The send level set with the soft switch is outputted. Used to
check the operation. (Only when FAX is installed.)
The send level set with the soft switch is outputted. Used to
check the operation. (Only when FAX is installed.)
Setup
FAX
Operation
19
Used to backup the Address data into the flash Memory
(Option FAX memory:AR-MM9)
(Only when FAX is installed.)
(Option FAX memory:AR-MM9)
(Only when FAX is installed.)
Setup
FAX
Operation
20
Used to restore the backup data (SIM 66-19) to Address data.
(Only when FAX is installed.)
(Only when FAX is installed.)
Setup
FAX
Operation
Code
Function (Content)
Purpose
Section
Item
Main Sub
[06]SIMULATIONS ・ FAXSOFTWARESWITCH.fm 2 ページ 2004年12月15日 水曜日 午後2時21分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-3
66
21
Used to print the FAX information (registrations, communication
management, file management, system errors, protocol).
(Only when FAX is installed.)
management, file management, system errors, protocol).
(Only when FAX is installed.)
Adjustment, setup,
operation data output,
check (display, print)
operation data output,
check (display, print)
FAX
Data
23
Used to download the FAX program.
(Only when FAX is installed.)
(Only when FAX is installed.)
Inhibited
FAX
24
Used clear the FAST memory data.
(Only when FAX is installed.)
(Only when FAX is installed.)
Inhibited
FAX
25
Used to register the FAX number for MODEM dial-in.
(Only when FAX is installed.)
(Only when FAX is installed.)
Inhibited
FAX
26
Used to register the external telephone number for MODEM
dial-in. (Only when FAX is installed.)
dial-in. (Only when FAX is installed.)
Inhibited
FAX
27
Used to register the voice-warp transfer number.
(Only when FAX is installed.)(Voice-warp:Japan only)
(Only when FAX is installed.)(Voice-warp:Japan only)
Inhibited
FAX
29
Used to clear the Address data.
Setup
FAX
Operation
30
Used to check TEL/LIU status change.
Setup
FAX
Operation
31
Used to set the TEL/LIU status.
Setup
FAX
Operation
32
Used to check received data.
Inhibited
FAX
33
Used to check signal detection.
Inhibited
FAX
34
Used to measure and display the communication time.
Setup
FAX
Operation
35
Modem program rewriting.(Only when FAX is installed.)
Operation test, check
FAX
Operation
36
Used to check I/F between MFPC and MDMC.
Check is made in the data line or the command line.
Check is made in the data line or the command line.
Operation test, check
FAX
Operation
39
Registration of FAX destination
FAX
42
Used to rewrite the program to the PIC installed in the FAX box.
To execute this simulation, FAX program writing must be
allowed. (Jumper and DIP switch which differ depending on the
model)
To execute this simulation, FAX program writing must be
allowed. (Jumper and DIP switch which differ depending on the
model)
FAX
43
To execute this simulation, FAX program writing must be
allowed. (Jumper and DIP switch which differ depending on the
model)The adjustment value of PIC are changed and written.
The current setting is highlighted beside the item.
allowed. (Jumper and DIP switch which differ depending on the
model)The adjustment value of PIC are changed and written.
The current setting is highlighted beside the item.
FAX
Code
Function (Content)
Purpose
Section
Item
Main Sub
[06]SIMULATIONS ・ FAXSOFTWARESWITCH.fm 3 ページ 2004年12月15日 水曜日 午後2時21分
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-4
5. Detail of simulations
<List of display values>
<List of display values>
<List of display values>
Main code 22
22-5
Purpose
Other
Function (Content)
Used to check the ROM version of each unit
(section).
(section).
Section
Item
Item
Software
Operation/Procedure The version of each ROM is displayed.
S/N
Engine section serial number
MFP
MFP controller
(LANGUAGE)
(Language version)
BOOT
MFP controller boot ROM
FAX
FAX controller
NIC
Network card
MAIL BIN
Mail bin controller
PCU
PCU controller
SCANNER
Scanner controller
FINISHER
Finisher controller
DESK
DESK/LCC controller
PUNCH UNIT
Punch unit
22-6
Purpose
Adjustment, setup, operation data output, check
(print)
(print)
Function (Content)
Used to print the list of adjustments and setup
data (simulations, FAX soft switches, counters).
data (simulations, FAX soft switches, counters).
Section
Item
Item
Data
Operation/Procedure The selected data is displayed on the right side
of the item.
0
TRAY SELECT auto only (no selection)
1
PRINT START
SIMULATION 22-5
ROM VERSION DATA DISPLAY.
S/N : 000000000
MFP : 1.00 (LANGUAGE : 1.00)
PCU : 1.00 BOOT : 1.00
SCANNER : 1.00 FAX : 1.00
FINISHER : 1.00 NIC : 1.00
DESK : 1.00 MAIL BIN : 1.00
PUNCH UNIT : 1.00
ROM VERSION DATA DISPLAY.
S/N : 000000000
MFP : 1.00 (LANGUAGE : 1.00)
PCU : 1.00 BOOT : 1.00
SCANNER : 1.00 FAX : 1.00
FINISHER : 1.00 NIC : 1.00
DESK : 1.00 MAIL BIN : 1.00
PUNCH UNIT : 1.00
SIMULATION 22-6
DATA PRINT MODE, SELECT SETTING,AND PRESS START.
0. TRAY SELECT
DATA PRINT MODE, SELECT SETTING,AND PRESS START.
0. TRAY SELECT
:AUTO ONLY
1. PRINT START
1
SIMULATION 22-6
DATA PRINT MODE.. EXECUTING
DATA PRINT MODE.. EXECUTING
0
When "1" is selected,
press [START] key.
press [START] key.
Press [CUSTOM SETTINGS] key
or [START] key
22-11
Purpose
Adjustment, setup, operation data output, check
(display)
(display)
Function (Content)
Used to check the use frequency of FAX.
(send/receive) (Only when FAX is installed.)
(send/receive) (Only when FAX is installed.)
Section
FAX
Item
Data
Operation/Procedure The counter data below are displayed.
FAX SEND
Number of times of FAX sending
FAX RECEIVE
Number of times of FAX receiving
FAX OUTPUT
FAX print quantity
SEND IMAGES
Quantity of sending
SEND TIME
Time for sending
RECEIVE TIME
Time for receiving
SIMULATION 22-11
FAX COUNTER DATA DISPLAY.
FAX SEND : ******** FAX RECEIVE : ********
FAX OUTPUT : ********
SEND IMAGES : ******** SEND TIME : ********:**:**
RECEIVE TIME : ********:**:**
FAX COUNTER DATA DISPLAY.
FAX SEND : ******** FAX RECEIVE : ********
FAX OUTPUT : ********
SEND IMAGES : ******** SEND TIME : ********:**:**
RECEIVE TIME : ********:**:**
[06]SIMULATIONS ・ FAXSOFTWARESWITCH.fm 4 ページ 2004年12月15日 水曜日 午後2時21分
Click on the first or last page to see other AR-FX12 (serv.man7) service manuals if exist.