Sharp AR-405 (serv.man31) User Manual / Operation Manual ▷ View online
5-3
CHAPTER
5
Misfeed in the RADF
When the RADF misfeeds an original sheet, the copier will stop and the
misfeed message will appear.
misfeed message will appear.
An original misfeed may occur at one of three locations:
(A) in the RADF feed section, (B) in the exit roller, or (C)
under the transport belt.
(A) in the RADF feed section, (B) in the exit roller, or (C)
under the transport belt.
(A) Open the feeding roller cover and pull the original gently
to the right and out from the document feeder tray.
●
Be sure to open and close the document feeder cover to cancel
the misfeed display.
the misfeed display.
(B) Open the exit roller cover and gently pull the original
out.
●
Be sure to open and close the document feeder cover to cancel
the misfeed display.
the misfeed display.
(C) Open the feeding roller cover and the document feeder
cover, and remove the original.
NOTE:
After misfed originals are removed from locations A, B and/or C, a
message may appear indicating the number of originals which
must be returned to the document feeder tray. Return the originals
and press the START (
After misfed originals are removed from locations A, B and/or C, a
message may appear indicating the number of originals which
must be returned to the document feeder tray. Return the originals
and press the START (
) key to resume copying.
MISFEED REMOVAL
COPIER TROUBLE?
Misfeed removal
A MISFEED HAS OCCURRED.
CLEAR INDICATED AREA.
PRESS FOR RECOVERY INSTRUCTIONS.
A
B
C
Feeding roller cover
Exit roller cover
5-4
CHAPTER
5
COPIER TROUBLE?
Misfeed removal
MISFEED REMOVAL
Misfeed in the bypass tray
1
Gently pull the misfed paper out.
2
Open and close the front cover to cancel the misfeed
display.
display.
A MISFEED HAS OCCURRED.
CLEAR INDICATED AREA.
PRESS FOR RECOVERY INSTRUCTIONS.
5-5
CHAPTER
5
COPIER TROUBLE?
Misfeed removal
MISFEED REMOVAL
Misfeed in paper trays 1 and 2
1
Open the right side cover.
●
Hold the handle and gently open the cover.
●
If any paper is set in the bypass tray, remove the paper and close
the bypass tray before opening the right side cover.
the bypass tray before opening the right side cover.
2
Remove the misfed paper.
●
Be careful not to tear the misfed paper during removal.
3
If the paper cannot be seen from the side, pull out the
paper tray which was in use and remove the misfed
paper.
paper tray which was in use and remove the misfed
paper.
●
Be careful not to tear the misfed paper during removal.
NOTE:
When the paper was misfed in tray 2 and the paper has dropped
beyond the tray, remove the tray and remove the misfed paper. To
remove the paper tray, pull the paper tray out until it stops and then
lift and remove the paper tray.
When the paper was misfed in tray 2 and the paper has dropped
beyond the tray, remove the tray and remove the misfed paper. To
remove the paper tray, pull the paper tray out until it stops and then
lift and remove the paper tray.
4
Close the paper tray and the side cover.
●
Confirm that the misfeed display is cleared.
A MISFEED HAS OCCURRED.
CLEAR INDICATED AREA.
PRESS FOR RECOVERY INSTRUCTIONS.
5-6
CHAPTER
5
MISFEED REMOVAL
COPIER TROUBLE?
Misfeed removal
Misfeed in the transport area
1
Open the front cover.
2
Remove the misfed paper.
1
Turn the transport lever to the left.
CAUTION
The area behind the transport lever is hot.
Use sufficient care in handling this lever.
Use sufficient care in handling this lever.
2
Turn roller rotating knob
A
in the direction of the arrow to
remove the misfed paper.
●
Push down the paper guide and remove any misfed paper.
A MISFEED HAS OCCURRED.
CLEAR INDICATED AREA.
PRESS FOR RECOVERY INSTRUCTIONS.
Paper guide
Transport lever
Roller rotating knob
A
Click on the first or last page to see other AR-405 (serv.man31) service manuals if exist.