Sharp AR-206 (serv.man7) User Manual / Operation Manual ▷ View online
7
GETTING ST
AR
TED
PART NAMES AND FUNCTIONS
Press and hold down the key.
12,345
sheets output
1st display
2nd display
Note:
●
Two-sided copies are counted as two copies.
●
A3 (11" x 17") size copies are counted as two copies.
CLEAR (
) key
Clears the copy quantity display or terminates a copy
run.
run.
START (
) key and indicator
Copying is possible when the indicator is on.
Press to start copying.
Press to start copying.
CLEAR ALL (
) key
Clears all selected settings and returns the copier to the
initial settings.
initial settings.
PRESET RATIO selector keys and indicators
(p. 17)
Use to sequentially select preset reduction/enlargement
copy ratios: 50%, 70%, 81%, 86%, 100%, 115%, 122%,
141%, 200% (50%, 64%, 77%, 95%, 100%, 121%,
129%, 141%, 200%).
(p. 17)
Use to sequentially select preset reduction/enlargement
copy ratios: 50%, 70%, 81%, 86%, 100%, 115%, 122%,
141%, 200% (50%, 64%, 77%, 95%, 100%, 121%,
129%, 141%, 200%).
ORIGINAL SIZE ENTER (
) key and
indicators
Use to input the original size.
Use to input the original size.
AUTO PAPER SELECT (
) indicator
Paper of the proper size will be automatically selected
depending on the original size and selected copy ratio
when this indicator is on.
depending on the original size and selected copy ratio
when this indicator is on.
TRAY SELECT (
) key (p. 14)
Use to manually select a paper tray.
AUTO IMAGE (
) key and indicator
Press for automatic copy ratio selection.
Paper feed location/misfeed location indica-
tors (p. 31)
The selected paper feed location is shown by a lit
indicator (
tors (p. 31)
The selected paper feed location is shown by a lit
indicator (
).
The general location of misfed paper is shown by a
blinking red indicator (
blinking red indicator (
).
DUAL PAGE COPY (
) key and indicator
(p. 25)
Use to make individual copies of two originals placed
side by side on the original table.
Use to make individual copies of two originals placed
side by side on the original table.
ERASE (
/
) key and indicators (p. 69)
Press to select the edge erase and/or the centre erase
mode. (Only available when an optional electronic
sorting kit is installed)
mode. (Only available when an optional electronic
sorting kit is installed)
MARGIN SHIFT (
) key and indicator (p. 71)
Shifts text or image on the copy to leave a binding
margin on the left (or the top) side of the copy. (Only
available when an optional electronic sorting kit is
installed)
margin on the left (or the top) side of the copy. (Only
available when an optional electronic sorting kit is
installed)
ORIGINAL TO COPY key and indicators (p. 20,
58)
Press to select one-sided and two-sided copy modes.
58)
Press to select one-sided and two-sided copy modes.
: Two-sided copies from one-sided
originals.
: Two-sided copies from two-sided
originals. (Can be selected only when an
optional RSPF is installed.)
optional RSPF is installed.)
: One-sided copies from two-sided
originals. (Can be selected only when an
optional RSPF is installed.)
optional RSPF is installed.)
Initial settings
The copier assumes the initial settings when it is first turned
on, when the CLEAR ALL (
The copier assumes the initial settings when it is first turned
on, when the CLEAR ALL (
) key is pressed, or ap-
proximately one minute* after the last copy is made in any
mode.
mode.
●
Copy ratio: 100%
●
Exposure: Automatic
●
Copy quantity: 0
●
All special copier modes: Off
●
Auto paper selection: On
●
Paper feed station: Previously selected paper tray
* This time (auto clear time) can be changed. See page 37,
USER PROGRAMS.
P
art names and functions
GETTING ST
AR
TED
Inch system
In some countries and regions, 8-1/2" x 13" size
is indicated on the operation panel.
is indicated on the operation panel.
8
GETTING ST
AR
TED
COPIER INSTALLATION
Improper installation may damage the copier. Please note the following
during initial installation and whenever the copier is moved.
during initial installation and whenever the copier is moved.
If the copier is moved from a cool place to a warm place, condensation may form inside the copier.
Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room
temperature for at least 2 hours before use.
Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room
temperature for at least 2 hours before use.
Do not install your copier in areas that are:
●
damp, humid, or very dusty
●
exposed to direct sunlight
●
poorly ventilated
●
subject to extreme temperature or humidity changes, e.g., near an
air conditioner or heater.
air conditioner or heater.
The copier should be installed near an accessible power outlet
for easy connection.
for easy connection.
Be sure to connect the power cord only to a power outlet that
meets the specified voltage and current requirements.
Also make certain the outlet is properly grounded.
meets the specified voltage and current requirements.
Also make certain the outlet is properly grounded.
●
For this copier’s power supply requirements, see the name plate
located on the back of the unit.
located on the back of the unit.
Connect the copier to a power outlet which is not used
for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.
for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.
Be sure to allow the required space around the machine for
servicing and proper ventilation.
servicing and proper ventilation.
Copier installation
10 cm (4")
9
GETTING ST
AR
TED
CAUTIONS ON HANDLING
Be careful in handling the copier as follows to maintain the performance of
this copier.
this copier.
Do not drop the copier, subject it to shock or strike it against any
object.
object.
Store spare toner cartridges in a cool dry place without removing
from the package before use.
If they are exposed to direct sunlight or excessive heat, poor copies
may result.
from the package before use.
If they are exposed to direct sunlight or excessive heat, poor copies
may result.
Do not touch the photoconductive drum (green portion).
Scratches or smudges on the drum will cause dirty copies.
Scratches or smudges on the drum will cause dirty copies.
Cautions on handling
10
GETTING ST
AR
TED
LOADING COPY PAPER
To save space, this copier has been designed with adjustable front-loading
trays, which are easily opened for paper loading. For best results, use only
SHARP recommended paper. (See page 51.)
The paper required (
trays, which are easily opened for paper loading. For best results, use only
SHARP recommended paper. (See page 51.)
The paper required (
) indicator will light up when there is no copy paper
in the selected paper feed station, or when the selected paper tray is not
installed or is improperly installed.
installed or is improperly installed.
When the paper size is changed in a paper tray, the size
of the paper must be entered by steps 8 through 11 on
page 12. If not, the edges of copies may become smudged
with toner. Also, the AUTO PAPER SELECT and the AUTO
IMAGE features will not function properly.
of the paper must be entered by steps 8 through 11 on
page 12. If not, the edges of copies may become smudged
with toner. Also, the AUTO PAPER SELECT and the AUTO
IMAGE features will not function properly.
1
Gently lift and pull out the paper tray until it stops.
2
Push the pressure plate down until it locks in place.
3
Fan the copy paper and insert it into the tray. Make sure
the edges go under the corner hooks.
the edges go under the corner hooks.
●
If you change to a different size of copy paper, the tray must be
adjusted. See the next page.
adjusted. See the next page.
●
Set the paper along the guides.
●
The tray holds up to 250 sheets of paper.
Do not load paper above the maximum height line.
Do not load paper above the maximum height line.
4
Push the paper tray firmly back into the copier.
Loading cop
y paper
Maximum height line
Click on the first or last page to see other AR-206 (serv.man7) service manuals if exist.