Sharp AR-206 (serv.man7) User Manual / Operation Manual ▷ View online
27
MAKING COPIES
1
Press the AUTO/MANUAL/PHOTO (
/
/
) key to
select the PHOTO (
) mode.
2
Press and hold down the AUTO/MANUAL/PHOTO (
/
/
) key for approximately 5 seconds.
●
The PHOTO (
) indicator will go out and the AUTO indicator will
begin to blink.
●
One or two exposure indicators corresponding to the current auto-
matic exposure level will light up. The factory default setting is level
“3”.
matic exposure level will light up. The factory default setting is level
“3”.
3
Press the light (
) or dark(
) key to lighten or darken
the automatic exposure level as desired.
4
Press the AUTO/MANUAL/PHOTO (
/
/
) key.
●
The AUTO indicator will stop blinking and will light up steadily.
●
This automatic exposure level will remain in effect until you change
it again by this procedure.
it again by this procedure.
Automatic exposure adjustment
AUTOMATIC EXPOSURE ADJUSTMENT
The automatic exposure level can be adjusted to suit your copying needs.
This level is set for copying from the original table and copying from the
optional SPF or RSPF respectively. To set the level for the optional SPF or
RSPF, place an original in the document feeder tray and make sure that the
SPF indicator lights up before proceeding to step 1. To set the level for the
original table, ensure that the SPF indicator does not light up.
This level is set for copying from the original table and copying from the
optional SPF or RSPF respectively. To set the level for the optional SPF or
RSPF, place an original in the document feeder tray and make sure that the
SPF indicator lights up before proceeding to step 1. To set the level for the
original table, ensure that the SPF indicator does not light up.
28
MAKING COPIES
Toner save mode
1
Press the AUTO/MANUAL/PHOTO (
/
/
) key to
select the MANUAL (
) mode.
2
Press and hold down the AUTO/MANUAL/PHOTO (
/
/
) key for approximately 5 seconds.
●
The MANUAL (
) indicator will go out and the PHOTO (
)
indicator will begin to blink.
●
The exposure indicator marked “5” will light up, indicating that the
standard toner mode is active.
standard toner mode is active.
3
To enter the toner save mode, press the light (
) key.
●
The exposure indicator marked “1” will light up, indicating that the
toner save mode is selected.
toner save mode is selected.
4
Press the AUTO/MANUAL/PHOTO (
/
/
) key.
●
The PHOTO (
) indicator will stop blinking and will light up
steadily. The toner save mode is now active.
●
To return to the standard mode, repeat the procedure but use the dark
(
(
) key to select exposure level “5” in step 3.
TONER SAVE MODE
This mode reduces toner consumption by approximately 10% in the automatic
and manual exposure modes. Copies will be lighter but still adequate for
general use. Selection of this mode does not affect the PHOTO mode. Follow
the procedure below for setting the toning level.
and manual exposure modes. Copies will be lighter but still adequate for
general use. Selection of this mode does not affect the PHOTO mode. Follow
the procedure below for setting the toning level.
29
ST
A
A
TUS
INDICA
T
ORS
1
Open the bypass tray. Lift slightly on the side cover
and slide the cover out until it stops.
and slide the cover out until it stops.
2
Push gently on both sides of the front cover and open it.
3
Push the toner cartridge lock release lever and pull the
toner cartridge out. Remove the toner cartridge while
supporting it with the left hand at the green label position.
toner cartridge out. Remove the toner cartridge while
supporting it with the left hand at the green label position.
●
For disposal of the old toner cartridge, contact your dealer.
After removing the toner cartridge, do not shake it or tap
on it. Doing so may cause toner to leak from the
cartridge. Put the old cartridge immediately in the bag
contained in the box of the new cartridge.
on it. Doing so may cause toner to leak from the
cartridge. Put the old cartridge immediately in the bag
contained in the box of the new cartridge.
4
Remove the new toner cartridge from the bag. Grasp the
cartridge on both sides and shake it horizontally four or
five times. After shaking the cartridge, remove the tape.
cartridge on both sides and shake it horizontally four or
five times. After shaking the cartridge, remove the tape.
Grasp the grip when holding the cartridge. Do not hold
the cartridge by the shutter. Be sure to only shake the
cartridge before the tape is removed.
the cartridge by the shutter. Be sure to only shake the
cartridge before the tape is removed.
TONER CARTRIDGE REPLACEMENT
When the toner cartridge replacement required (
) indicator lights up,
replacement of the toner cartridge will be needed soon. Obtain a new
cartridge. When the toner cartridge replacement required (
cartridge. When the toner cartridge replacement required (
) indicator
blinks, the toner cartridge must be replaced before copying can be resumed.
Replace the toner cartridge by following the procedure below.
Replace the toner cartridge by following the procedure below.
For best copying results, be sure to use only
SHARP products.
The package of SHARP toner has the Genuine
Supplies label.
SHARP products.
The package of SHARP toner has the Genuine
Supplies label.
Toner cartridge replacement
Grip
Toner cartridge lock
release lever
release lever
4 or 5 times
Tape
Shutter
GENUINE SUPPLIES
During a long copy run of a dark original, the
indicator
may blink and the copier stop, even though toner is left.
The copier will feed toner up to 2 minutes and then the
START key (
The copier will feed toner up to 2 minutes and then the
START key (
) indicator will light up. Press the START
(
) key to restart copying.
30
ST
A
A
TUS
INDICA
T
ORS
Toner cartridge replacement
TONER CARTRIDGE REPLACEMENT
5
Gently insert the toner cartridge along the guides until
it locks in place while pushing the lock release lever.
it locks in place while pushing the lock release lever.
If dirt or dust is adhered to the toner cartridge, remove
it before installing the cartridge.
it before installing the cartridge.
6
Remove the tape from the shutter. Pull the shutter out of
the toner cartridge as shown in the illustration. Discard
the shutter.
the toner cartridge as shown in the illustration. Discard
the shutter.
7
Close the front cover by pushing both sides with your
hands and then close the side cover by pressing the
handle on the cover. The
hands and then close the side cover by pressing the
handle on the cover. The
indicator will go out.
When closing the covers, be sure to close the front
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
Even after a new toner cartridge is installed, the START
key indicator may not light up, indicating copying cannot
be restarted (toner is not sufficiently fed). In this case,
open and close the side cover. The copier will feed
toner again approximately 2 minutes and then copying
can be restarted.
key indicator may not light up, indicating copying cannot
be restarted (toner is not sufficiently fed). In this case,
open and close the side cover. The copier will feed
toner again approximately 2 minutes and then copying
can be restarted.
Toner cartridge life
To find out the approximate quantity of toner remaining, follow the procedure
below.
below.
1
Press and hold the light (
) key for more than 5
seconds until all the alarm indicators (
,
,
,
,
and
) blink and “– –” appears in the copy quantity
display.
2
Press and hold the copy ratio display (
) key for more
than 5 seconds.
●
The approximate quantity of toner remaining will be indicated in the
copy quantity display as a percentage. ( “100”, “75”, “50”, “25”, or
“10” is displayed.) When the percentage is less than 10%, “LO” will
be displayed.
copy quantity display as a percentage. ( “100”, “75”, “50”, “25”, or
“10” is displayed.) When the percentage is less than 10%, “LO” will
be displayed.
3
Press the light (
) key.
●
All the alarm indicators will go out.
Click on the first or last page to see other AR-206 (serv.man7) service manuals if exist.