Sharp AR-206 (serv.man7) User Manual / Operation Manual ▷ View online
35
ST
A
A
TUS
INDICA
T
ORS
Misfeed removal
Misfeed in the lower paper tray
1
Grasp the handle of the lower side cover and gently
open the cover.
open the cover.
2
Remove the misfed paper.
●
Be careful not to tear the misfed paper during removal.
3
If the misfed paper is not seen in step 2, gently lift and
pull out the lower paper tray and remove the misfed
paper.
pull out the lower paper tray and remove the misfed
paper.
●
Be careful not to tear the misfed paper during removal.
4
Close the paper tray.
5
Close the lower side cover.
●
The misfeed (
) indicator will go out.
MISFEED REMOVAL
36
ST
A
A
TUS
INDICA
T
ORS
Developer required/
Maintenance required
MAINTENANCE REQUIRED
When the
indicator lights up, service by an authorised SHARP service
technician is required. Contact your service centre as soon as possible.
When the
indicator lights up, the developer should be replaced.
DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN
AUTHORISED SHARP SERVICE TECHNICIAN. Contact your service
centre as soon as possible.
AUTHORISED SHARP SERVICE TECHNICIAN. Contact your service
centre as soon as possible.
DEVELOPER REQUIRED
37
GENERAL INFORMA
TION
Program No.
Program name
Description
1
Auto clear time
Sets the auto clear time. The copier returns to the initial settings
when the auto clear time elapses after the last copy is made.
when the auto clear time elapses after the last copy is made.
2
Preheat mode
Sets the time that elapses before the copier enters the preheat
mode after any operation is made. See page 44.
mode after any operation is made. See page 44.
3
Auto power shut-off
Sets the time that elapses before the copier enters the auto power
timer
shut-off mode after any operation is made. See page 44.
4
Stream feeding
Enables or disables the stream feeding mode when an optional SPF or
mode*
RSPF is installed. See page 58.
5
Auto power shut-off
Enables or disables the auto power shut-off mode. See page 44.
setting
6
Border line for 2 in 1 or
Enables or disables the border line which is printed in 2 in 1 or 4 in 1
4 in 1*
copying when an optional electronic sorting kit and an optional SPF or
RSPF are installed. See page 67.
RSPF are installed. See page 67.
7
Rotation copy*
Enables or disables rotation of original images. See page 64.
8
Auto paper select mode
Enables or disables the auto paper selection. See page 14.
9
Auto tray switching
Enables or disables the automatic tray switching which occurs when paper
in a tray runs out. (This switching cannot switch to the bypass tray.)
in a tray runs out. (This switching cannot switch to the bypass tray.)
10
Auditing mode
Enables or disables the auditing mode, which controls access to the
copier. See page 13.
copier. See page 13.
11
Account number entry
Registers accounts for auditing mode.
12
Account number
Changes account numbers for auditing mode.
change
13
Account number
Deletes accounts for auditing mode.
deletion
14
Number of copies
Displays the total number of copies made against account numbers.
per account
15
Resetting account
Resets all audit accounts or resets any desired individual account.
16
Erase width adjustment*
Sets the amount of the edge erase and centre erase areas. See page 69.
17
Layout in 2 in 1 copy*
Selects a pattern for 2 in 1 copying. See page 67.
18
Layout in 4 in 1 copy*
Selects a pattern for 4 in 1 copying. See page 67.
19
Offset of paper output
Enables or disables the offset function of the paper output tray. The offset
tray
function can be specified respectively for the upper and lower areas
separated by an optional job separator tray. See page 65.
separated by an optional job separator tray. See page 65.
20
Image rotation in
Enables or disables image rotation (180°) of the front side in one-sided to
duplex copying
two-sided copying or two-sided to one-sided copying. See page 62.
22
Location of the margin*
Selects the location of the expanded margin. See page 71.
* These programs do not affect the copier functions unless certain optional equipment is installed.
User programs
USER PROGRAMS
The user programs allow the parameters of certain functions to be set,
changed, or cancelled as desired.
changed, or cancelled as desired.
List of user programs
This copier has the following user programs.
38
GENERAL INFORMA
TION
Setting the user programs
1
Press and hold the light (
) key for more than 5
seconds until all the alarm indicators (
,
,
,
,
and
) blink and “– –” appears in the copy quantity
display.
2
Enter a program number using the numeric keys.
●
The selected program number will blink in the copy quantity display.
●
If a mistake is made in steps 2 to 4, press the CLEAR (
) key. The
copier will return to step 2.
●
The program numbers are shown in the table below.
For example, to change the setting of the auto power shut-off timer,
press key 3.
For example, to change the setting of the auto power shut-off timer,
press key 3.
Program name
Program No.
Auto clear time
1
Preheat mode
2
Auto power shut-off timer
3
Stream feeding mode
4
Auto power shut-off setting
5
Border line for 2 in 1 or 4 in 1
6
Rotation copy
7
Auto paper select mode
8
Auto tray switching
9
Auditing mode
10
Account number entry
11
Account number change
12
Account number deletion
13
Number of copies per account
14
Resetting account
15
Erase width adjustment
16
Layout in 2 in 1 copy
17
Layout in 4 in 1 copy
18
Offset of paper output tray
19
Image rotation in duplex copying
20
Location of the margin
22
3
Press the START (
) key.
●
For programs 1 to 9 and 16 to 22, the entered program number will be
steadily lit on the left side of the copy quantity display and the
currently selected parameter number for the program will blink on the
right side.
steadily lit on the left side of the copy quantity display and the
currently selected parameter number for the program will blink on the
right side.
●
For programs 10 to 15 (programs for auditing accounts), the display
varies with the program number. See page 40 for setting programs 10
to 15.
varies with the program number. See page 40 for setting programs 10
to 15.
USER PROGRAMS
User programs
For operation of these programs after
step 3, see page 40.
step 3, see page 40.
Click on the first or last page to see other AR-206 (serv.man7) service manuals if exist.