Sharp AL-1644 (serv.man17) User Manual / Operation Manual ▷ View online
39
USER SETTINGS
4
*
3
AL-1633 is as follows:
1: Paper tray (factory default), 5: Bypass tray
1: Paper tray (factory default), 5: Bypass tray
19
Offset of paper output
tray
tray
0: OFF
1: ON
1: ON
• When enabled, this function offsets the position
in the paper output tray of interrupt copy jobs,
and print jobs when using the printer function.
and print jobs when using the printer function.
23
Resolution in
Auto/Text mode
Auto/Text mode
1: 300dpi
2: 600dpi
2: 600dpi
• The copy resolution in auto and text mode is
normally 300 dpi. If high-quality copies are
preferred, use this setting to change the
resolution to 600 dpi.
preferred, use this setting to change the
resolution to 600 dpi.
25
Key auto repeat
0: OFF
1: ON
1: ON
• Use this setting to select whether or not
holding down a key causes repeated input of
the key. For keys that normally cause a set
value to increase when held down (for
example, holding down the [ZOOM] key (
the key. For keys that normally cause a set
value to increase when held down (for
example, holding down the [ZOOM] key (
,
)), this program can be used to have the set
value not change when the key is held down.
26
Key press time
1: Minimum
(current response
speed)
speed)
2: 0.5 sec.
3: 1.0 sec.
4: 1.5 sec.
5: 2.0 sec.
3: 1.0 sec.
4: 1.5 sec.
5: 2.0 sec.
• Use this setting to select how long a key must
be pressed for the input to be accepted. By
selecting a longer time, you can prevent
settings from being changed by the accidental
pressing of a key.
selecting a longer time, you can prevent
settings from being changed by the accidental
pressing of a key.
27
Audible signals volume
1: Short beep
2: Long beep
3: OFF
2: Long beep
3: OFF
• This sets the volume of beep signals. (p.40)
28
Base setting beep
signal
signal
0: OFF
1: ON
1: ON
• Use this to sound a beep when a base setting
is selected. (p.40)
29
Number of copies limit
1: 99 copies
2: 999 copies
2: 999 copies
• Use this setting to select 99 or 999 for the
maximum number of copies.
30
Use close paper size
0: OFF
1: ON
1: ON
• When this function is enabled, printing in
printer mode will automatically continue using
a different size of paper if the specified size of
paper runs out in all trays. This feature does
not function in copy mode.
a different size of paper if the specified size of
paper runs out in all trays. This feature does
not function in copy mode.
31
Default tray setting
1: Upper paper tray*
3
2: Lower paper tray*
3
5: Bypass tray*
3
• Use this program to select a default tray. This
tray is automatically selected each time the
power is turned on or each time the machine
reverts to the initial settings.
power is turned on or each time the machine
reverts to the initial settings.
32
Default exposure
mode
mode
1: AUTO
2: TEXT
3: PHOTO
2: TEXT
3: PHOTO
• Use this program to set "AUTO", "TEXT", or
"PHOTO" as the default exposure mode.
Program
number
Program name
Setting codes
(factory default setting
appears in bold)
Explanation
AL-1633_1644_EX.book 39 ページ ２００３年１０月２３日 木曜日 午後８時２１分
40
USER SETTINGS
SELECTING A SETTING FOR A USER PROGRAM
1
Hold down the [Light] key (
) until
the alarm indicators (
,
,
,
)
blink.
The display shows "- -"
with the left hyphen
blinking.
with the left hyphen
blinking.
2
Enter the program number with the
numeric keys.
numeric keys.
• See "USER
PROGRAMS" (p.38 to
p.39) for the program
numbers.
p.39) for the program
numbers.
• The selected program
number blinks.
• For example, to select
"Auto clear timer",
press the [1] key.
press the [1] key.
3
Press the [START] key (
).
• The selected program
number stops blinking
and lights steadily.
and lights steadily.
• The currently selected
setting code blinks on
the right side of the
display.
the right side of the
display.
4
Enter the desired setting code by
pressing a numeric key.
pressing a numeric key.
• For the setting codes,
see "USER
PROGRAMS". (p.38 to
p.39)
PROGRAMS". (p.38 to
p.39)
• The selected setting
code blinks.
• For example, to select
90 seconds, press the
[5] key.
[5] key.
5
Press the [START] key (
).
The selected setting
code stops blinking and
lights steadily.
code stops blinking and
lights steadily.
6
Press the [Light] key (
) to complete
the settings.
The alarm indicators (
,
,
,
) go off
and the display returns to the number of copies
display.
display.
Audible signals (key entry beep, invalid key beep, base setting beep)
The machine sounds three different types of beep signals: a key entry beep that sounds when a valid key is
pressed, an invalid key beep that sounds when an invalid key is pressed, and a base setting beep that sounds
when a setting is the same as the base setting (base settings are explained below).
pressed, an invalid key beep that sounds when an invalid key is pressed, and a base setting beep that sounds
when a setting is the same as the base setting (base settings are explained below).
The base setting beep is
initially disabled. If you wish to enable the base setting beep, see "Base setting beep signal" on page 39. If you
wish to change the volume of the beep signals or disable them, see "Audible signals volume" on page 39.
The beep patterns of each type of beep signal are as follows:
wish to change the volume of the beep signals or disable them, see "Audible signals volume" on page 39.
The beep patterns of each type of beep signal are as follows:
Key entry beep ......................... One beep
Invalid key beep ......................Two beeps
Invalid key beep ......................Two beeps
Base setting beep ................ Three beeps
Base settings
The base settings are preset standard selections for each copy setting. The base settings are as follows:
Copy ratio ........................................ 100%
Light and Dark indicator........................ 3
Paper feed location ....... Upper paper tray
Light and Dark indicator........................ 3
Paper feed location ....... Upper paper tray
ORIGINAL SIZE........................................A4
AUTO/TEXT/PHOTO (
AUTO/TEXT/PHOTO (
/
/
)
............................................................ AUTO
If you enter the wrong number, press the
[CLEAR] key (
[CLEAR] key (
) and then enter the correct
number.
1 3 5
READ END
Note
If you enter the wrong number, press the
[CLEAR] key (
[CLEAR] key (
) and return to step 2.
To select a setting for another user program,
press the [CLEAR] key (
press the [CLEAR] key (
) and then return
to step 2.
Note
Note
AUTO
AL-1633_1644_EX.book 40 ページ ２００３年１０月２３日 木曜日 午後８時２１分
41
4
SETTINGS FOR AUDITING MODE
AUDITING MODE
When "Auditing mode" is enabled, a count is kept of the number of copies made by each account (up to 20 accounts
can be established), and the counts can be displayed and totalled as necessary. In "Auditing mode", the display
shows "- - -", and this indicates that a 3-digit account number must be entered in order to use the machine for
copying.
can be established), and the counts can be displayed and totalled as necessary. In "Auditing mode", the display
shows "- - -", and this indicates that a 3-digit account number must be entered in order to use the machine for
copying.
AUDITING MODE SETTINGS
The administrator of the machine should complete the following settings:
• Enable "Auditing mode" (p.43)
• Account number entry (p.43)
• Account number entry (p.43)
Note
Program
number
Program name
Setting codes
(factory default settings
are indicated in bold)
Explanation
10
Auditing mode
0: OFF
1: ON
1: ON
Use to enable or disable "Auditing mode".
"Auditing mode" is initially disabled.
"Auditing mode" is initially disabled.
11
Account number entry
None
Use to set up account numbers. Up to 20
accounts can be established.
accounts can be established.
12
Account number
change
change
None
Use to change an account number.
13
Account number
deletion
deletion
0: Delete single account
1: Delete all accounts
1: Delete all accounts
Use to delete an account number.
A single account number can be deleted, or all
account numbers at once.
A single account number can be deleted, or all
account numbers at once.
14
Number of copies per
account
account
None
This displays the number of copies made by
each account.
The maximum count is 49,999. If this number is
exceeded, the count will start over from 0.
each account.
The maximum count is 49,999. If this number is
exceeded, the count will start over from 0.
15
Resetting account
0: Reset single account
1: Reset all accounts
1: Reset all accounts
Use to reset the copy count of an account to 0.
The copy count of a single account or of all
accounts can be reset.
The copy count of a single account or of all
accounts can be reset.
AL-1633_1644_EX.book 41 ページ ２００３年１０月２３日 木曜日 午後８時２１分
42
USER SETTINGS
SELECTING AUDITING MODE SETTINGS
1
Hold down the [Light] key (
) until
the alarm indicators (
,
,
,
)
blink.
The display shows "- -"
with the left hyphen
blinking.
with the left hyphen
blinking.
2
Enter the program number with the
numeric keys.
numeric keys.
• See "AUDITING MODE
SETTINGS" (p.41) for
the program numbers.
the program numbers.
• The selected program
number blinks.
• For example, to select
"Auditing mode", enter
"10".
"10".
3
Press the [START] key (
).
• The selected program
number stops blinking
and lights steadily.
and lights steadily.
• The currently selected
setting code blinks on
the right side of the
display.
the right side of the
display.
4
Enter the desired setting code for the
program as explained in the detailed
procedures on the following pages.
program as explained in the detailed
procedures on the following pages.
For the setting codes, see "AUDITING MODE
SETTINGS". (p.41)
SETTINGS". (p.41)
5
Press the [Light] key (
) to complete
the settings.
The alarm indicators (
,
,
,
) go off
and the display returns to the number of copies
display.
display.
If you enter the wrong number, press the
[CLEAR] key (
[CLEAR] key (
) and then enter the correct
number.
• If you enter the wrong number, press the
[CLEAR] key (
) and return to step 2.
• If "E" (error code) blinks in the first digit of
the display, press the [CLEAR] key (
)
and return to step 2.
1 3 5
READ END
Note
Note
AL-1633_1644_EX.book 42 ページ ２００３年１０月２３日 木曜日 午後８時２１分
Click on the first or last page to see other AL-1644 (serv.man17) service manuals if exist.