Sharp AL-1611 (serv.man24) User Manual / Operation Manual ▷ View online
23
MAKING COPIES
Bypass feed (special paper)
BYPASS FEED (special paper)
The bypass tray is used to copy onto transparency film, labels, and other
special purpose papers. Up to 100 sheets of standard copy paper can be set
in the bypass tray.
special purpose papers. Up to 100 sheets of standard copy paper can be set
in the bypass tray.
For special purpose papers, the original image must be
smaller than the paper or media for copying.
If the original image is bigger than the paper or media, this
may cause smudges on the edges of the copies.
Also for standard copy paper, smudges may appear if the
copy paper is not at least as large as the original image.
smaller than the paper or media for copying.
If the original image is bigger than the paper or media, this
may cause smudges on the edges of the copies.
Also for standard copy paper, smudges may appear if the
copy paper is not at least as large as the original image.
1
Unfold the bypass tray.
●
When feeding B4 or A3 sized paper, extend the feeder tray.
2
Set the paper guides to the copy paper width.
3
Insert the copy paper (print face down) all the way into
the bypass tray.
the bypass tray.
●
Up to 100 sheets of standard copy paper measuring from A6 to A3 can
be loaded in the bypass tray.
be loaded in the bypass tray.
●
A6 size paper must be fed narrow into the feed slot.
●
Transparency film, labels, and other special purpose papers (except
envelopes) must be fed individually.
Up to 10 envelopes can be set.
envelopes) must be fed individually.
Up to 10 envelopes can be set.
●
When adding paper, first remove remaining paper, combine it with the
paper to be added and then reload as a single stack.
paper to be added and then reload as a single stack.
●
When loading envelopes, make sure that they are straight and flat.
24
MAKING COPIES
BYPASS FEED (special paper)
Bypass feed (special paper)
4
Press the TRAY SELECT key to select the bypass tray.
5
Leave the copy quantity at 0 if using special papers. Set
the number of copies if using standard copy paper or
envelopes.
the number of copies if using standard copy paper or
envelopes.
6
Press the START key.
25
MAKING COPIES
Two-sided copying
TWO-SIDED COPYING
Two-sided copies can be made on this copier using the bypass tray.
1
Place the first original on the original table and make a
copy.
copy.
●
The first copy can be made using any of the paper feed stations.
2
Replace the first original with the second original and
close the document feeder cover or the platen cover.
close the document feeder cover or the platen cover.
●
Make sure that the first and second originals are oriented in the same
way on the original table.
way on the original table.
●
When the originals are placed horizontally, make sure that the first and
second originals are oriented in the reverse way on the original table.
second originals are oriented in the reverse way on the original table.
With AL-1622, both the first and second originals can
be set in the SPF but they must be set separately. If the
stream feeding mode for the SPF has been enabled,
set the second original after the SPF (
be set in the SPF but they must be set separately. If the
stream feeding mode for the SPF has been enabled,
set the second original after the SPF (
) indicator goes
out. See page 20.
3
Turn the first copy over left to right and place it into the
bypass tray.
bypass tray.
●
Be sure to feed the copies one sheet at a time.
4
Use the TRAY SELECT key to select the bypass tray.
5
Press the START key.
26
MAKING COPIES
XY zoom
Original
Copy
XY ZOOM
The XY ZOOM feature allows the horizontal and vertical copy ratios to be
changed independently.
To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the
DUAL PAGE COPY feature first and then the XY ZOOM feature.
(Enlargement cannot be set.)
changed independently.
To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the
DUAL PAGE COPY feature first and then the XY ZOOM feature.
(Enlargement cannot be set.)
1
Place the original on the original table or in the document
feeder tray.
feeder tray.
2
Press the XY-ZOOM key.
●
The current value for the vertical direction will be displayed in the
copy quantity display.
copy quantity display.
3
Use the PRESET RATIO selector (
,
) keys and zoom
(
,
) keys to change the copy ratio in the vertical
direction.
●
Press a PRESET RATIO selector (
or
) key to set an approximate
ratio, then press the
key to decrease the ratio or
key to increase
the ratio. The copy ratio will be displayed in the copy quantity display.
4
Press the copy ratio display (
) key.
●
The selected ratio for the vertical direction will be entered and the
current value for the horizontal direction will be displayed in the copy
quantity display.
current value for the horizontal direction will be displayed in the copy
quantity display.
Click on the first or last page to see other AL-1611 (serv.man24) service manuals if exist.