Sharp AL-1611 (serv.man24) User Manual / Operation Manual ▷ View online
7
GETTING ST
AR
TED
PART NAMES AND FUNCTIONS
Zero key
Use as part of numeric keys to enter copy quantity.
Press during a continuous copy run to display the
number of copies completed in the current run.
Press and hold during standby to display the total output
count.
Use as part of numeric keys to enter copy quantity.
Press during a continuous copy run to display the
number of copies completed in the current run.
Press and hold during standby to display the total output
count.
Press and hold down the key.
12,345
sheets output
1st display
2nd display
Note: A3 size copies are counted as two copies.
CLEAR key
Clears the copy quantity display or terminates a copy
run.
Clears the copy quantity display or terminates a copy
run.
START key and indicator
Copying is possible when the indicator is on.
Press to start copying.
Copying is possible when the indicator is on.
Press to start copying.
CLEAR ALL key
Clears all selected settings and returns the copier to the
initial settings.
Clears all selected settings and returns the copier to the
initial settings.
PRESET RATIO selector keys and indicators
(p. 22)
Use to sequentially select preset reduction/enlargement
copy ratios: 50%, 70%, 81%, 86%, 100%, 115%, 122%,
141%, 200%.
(p. 22)
Use to sequentially select preset reduction/enlargement
copy ratios: 50%, 70%, 81%, 86%, 100%, 115%, 122%,
141%, 200%.
ORIGINAL SIZE ENTER key and indicators
(p. 21)
Use to input the original size for automatic paper selection
(AL-1622 only) and automatic copy ratio selection.
(p. 21)
Use to input the original size for automatic paper selection
(AL-1622 only) and automatic copy ratio selection.
AUTO PAPER SELECT indicator (AL-1622 only)
Paper of the proper size will be automatically selected
depending on the original size and selected copy ratio
when this indicator is on.
Paper of the proper size will be automatically selected
depending on the original size and selected copy ratio
when this indicator is on.
TRAY SELECT key (p. 17)
Use to manually select a paper tray.
Use to manually select a paper tray.
AUTO IMAGE key and indicator
Press for automatic copy ratio selection.
Press for automatic copy ratio selection.
Paper feed location/misfeed location indicators
(p. 39)
The selected paper feed location is shown by a lit
indicator (
(p. 39)
The selected paper feed location is shown by a lit
indicator (
).
The general location of misfed paper is shown by a
blinking red indicator (
blinking red indicator (
).
DUAL PAGE COPY key and indicator (p. 29)
Use to make individual copies of two originals placed
side by side on the original table.
Use to make individual copies of two originals placed
side by side on the original table.
Initial settings
The copier assumes the initial settings when it is first turned
on, when the CLEAR ALL key is pressed, and approximately
one minute* after the last copy is made in any mode.
The copier assumes the initial settings when it is first turned
on, when the CLEAR ALL key is pressed, and approximately
one minute* after the last copy is made in any mode.
●
Copy ratio: 100%
●
Exposure: Automatic
●
Copy quantity: 0
●
All special copier modes: Off
●
Auto paper selection : On (AL-1622 only)
●
Paper feed station: Previously selected paper tray
* This time (auto clear time) can be changed. See page 45,
USER PROGRAMS.
P
ar
t names and functions
GETTING ST
AR
TED
The illustration on the left shows
the operation panel of AL-1622.
The portion of the operation panel
of AL-1611 that is different from
AL-1622 is shown above.
the operation panel of AL-1622.
The portion of the operation panel
of AL-1611 that is different from
AL-1622 is shown above.
8
GETTING ST
AR
TED
10 cm
Copier installation
COPIER INSTALLATION
Improper installation may damage the copier. Please note the following
during initial installation and whenever the copier is moved.
during initial installation and whenever the copier is moved.
If the copier is moved from a cool place to a warm place, condensation may form inside the copier.
Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room
temperature for at least 2 hours before use.
Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room
temperature for at least 2 hours before use.
Do not install your copier in areas that are:
●
damp, humid, or very dusty
●
exposed to direct sunlight
●
poorly ventilated
●
subject to extreme temperature or humidity changes, e.g., near an
air conditioner or heater.
air conditioner or heater.
The copier should be installed near an accessible power outlet
for easy connection.
for easy connection.
Be sure to connect the power cord only to a power outlet that
meets the specified voltage and current requirements.
Also make certain the outlet is properly grounded.
meets the specified voltage and current requirements.
Also make certain the outlet is properly grounded.
●
For this copier’s power supply requirements, see the name plate located
on the back of the unit.
on the back of the unit.
Connect the copier to a power outlet which is not used
for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.
for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.
Be sure to allow the required space around the machine for
servicing and proper ventilation.
servicing and proper ventilation.
A small amount of ozone is produced within the copier during operation. The emission level is insufficient to
cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m
cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m
3
) calculated as an 8 hr.
time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the
copier in a ventilated area.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the
copier in a ventilated area.
9
GETTING ST
AR
TED
CAUTIONS ON HANDLING
Be careful in handling the copier as follows to maintain the performance of
this copier.
this copier.
Do not drop the copier, subject it to shock or strike it against any
object.
object.
Do not expose the drum cartridge to direct sunlight.
Doing so will damage the surface (green portion) of the drum
cartridge, causing poor copy quality.
Doing so will damage the surface (green portion) of the drum
cartridge, causing poor copy quality.
Store spare supplies such as drum cartidges and TD cartridges
in a cool dry place without removing from the package before
use.
If they are exposed to direct sunlight or excessive heat, poor copies
may result.
in a cool dry place without removing from the package before
use.
If they are exposed to direct sunlight or excessive heat, poor copies
may result.
Do not touch the surface (green portion) of the drum cartridge.
Scratches or smudges on the drum will cause dirty copies.
Scratches or smudges on the drum will cause dirty copies.
Cautions on handling
10
GETTING ST
AR
TED
CHECKING PACKED COMPONENTS
AND ACCESSORIES
AND ACCESSORIES
Open the carton and check to ensure that the following components and
accessories are included.
accessories are included.
Copier
TD cartridge
Operation manual
Power cord
Drum cartridge
(installed in copier)
●
If anything is not included or is damaged, contact your authorised service representative.
●
Save the carton and packing materials. These can be re-used for transporting the machine, should
it be necessary.
it be necessary.
Unpacking
Be sure to lift by the handles on both sides of the copier by two persons to
unpack the copier and carry it to the installation location.
unpack the copier and carry it to the installation location.
Checking pack
ed components and accessor
ies
Click on the first or last page to see other AL-1611 (serv.man24) service manuals if exist.