DOWNLOAD Sharp PN-ZB01 Service Manual ↓ Size: 9.48 MB | Pages: 127 in PDF or view online for FREE

PN-V602　OUTLINE OF THE PRODUCT

 1 – 17

7 ) Attach the expansion board.

Fully insert the connector.

8 ) Secure the expansion board.

Secure the board with the 2 screws removed in Step 4).

9 ) Attach the attach the expansion terminal cover A.

Secure the cover with the 8 screws removed in Step 3).

10 )Affix the terminal label in the area indicated by (A) in the above

illustration.

Connector

Connector

ᲢAᲣ

PN-V602　INSTALLATION, ADJUSTMENT, SETTING

 2 – 1

n

This product is for use indoors.

n

Since the monitor is heavy, consult your dealer before installing,

removing or moving the monitor.

n

When installing, removing or moving the monitor, ensure that this
is carried out by at least 2 people.

n

A mounting bracket compliant with VESA specifications is required.

Do not use any screw holes other than VESA holes for installation.

n

To attach a VESA-compliant mounting bracket, use M6 screws

that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the

thickness of the mounting bracket.

n

When moving the monitor, be sure to hold it with the handles both
on the rear and the unit bottom. Do not hold the LCD panel. This

may cause product damage, failure, or injury.

n

Install the monitor with the surface perpendicular to a level sur-

face. If necessary, the monitor may be tilted up to 20 degrees
upward or downward.

n

When mounting the monitor horizontally, the optional fan cover

(PN-ZR31) is required. For details along with the horizontal

mounting conditions, consult your dealer where the monitor was
purchased.

n

When performing an installation where the monitor is stacked,

please install it such that load is not placed on the monitor frame.

n

Mounting the monitor on the wall requires special expertise and

the work must be performed by an authorized SHARP dealer.
You should never attempt to perform any of this work yourself.

Our company will bear no responsibility for accidents or injuries

caused by improper mounting or mishandling.

n

This monitor should be used at an ambient temperature between
32°F (0°C) and 104°F (40°C).

n

Be careful of high temperatures in the surrounding area. 

When installing the monitor inside a housing, or if the ambient

temperature may be outside of the range of 32°F (0°C) to 104°F
(40°C), install a fan or take other measures to keep the ambient

temperature within the required range.

n

Temperature condition may change when using the display

together with the optional equipments recommended by SHARP.
In such cases, please check the temperature condition specified

by the optional equipments.

n

Adhere to the following when installing the monitor in its vertical

orientation. Failing to adhere to the following may cause malfunc-
tions.

--- To install in horizontal orientation, rotate the monitor 90 degrees

to the right.

--- Set the “MONITOR” on the SETUP menu to “PORTRAIT”. 

--- Be sure to secure the power cord (supplied) to the cable clamp

attachment below with the supplied cable clamp. Make sure
that the power cord (supplied) does not supply power to the

terminal when being secured and do not over bend the power

cord (supplied).

n

Do not block any ventilation openings. If the temperature inside

the monitor rises, this could lead to a malfunction.

n

After mounting, please carefully ensure the monitor is secure,

and not able to come loose from the wall or mount.

n

Do not place the monitor on a device which generates heat.

n

Be sure to use a wall-mount bracket designed or designated for
mounting the monitor.

n

This monitor is designed to be installed on a concrete wall or pil-

lar. Reinforced work might be necessary for some materials such

as plaster / thin plastic board / wood before starting installation. 
This monitor and bracket must be installed on a wall which can

endure at least 4 times or more the weight of the monitor. Install

by the most suitable method for the material and the structure.

Cable clamp
attachment

Power cord (Supplied)

Cable clamp

PN-V602　INSTALLATION, ADJUSTMENT, SETTING

 2 – 2

n

Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/disconnecting cables. Also, read the

manual of the equipment to be connected.

n

Be careful not to mix up the input terminal with the output terminal when connecting cables. Mixing up the input and output terminals may cause

malfunctions and the other problems.

n

Images may not be displayed properly depending on the computer (video card) to be connected.

n

A screen with 1920 x 1080 resolution may not be displayed correctly on “PC RGB”. In this case, check the settings of your computer (video
card) to verify that input signals conform to specifications of this monitor.

n

If there is a check box to disable EDID in display control panel, check it when using “PC RGB”.

n

Use the automatic screen adjustment when a PC screen is displayed for the first time using “PC D-SUB” or “PC RGB”, or when the setting of

the PC is changed. The screen is adjusted automatically when “SELF ADJUST” in the OPTION menu is set to “ON”.

n

If the audio output from the playback device is connected directly to speakers or other devices, the video on the monitor may appear delayed

from the audio portion.
Audio should be played through this monitor by connecting the playback device to the monitor’s audio input, and connecting the monitor’s

audio output to the speakers or other devices.

n

The audio input terminals used in each input mode are factory-set as follows.

■ CONNECTION WITH A PC OR AV EQUIPMENT

PC D-SUB

PC DVI-D
PC RGB

Audio input terminal

AV DVI-D

Audio1 input terminal

AV COMPONENT(BNC)
AV S-VIDEO

AV VIDEO (BNC)

Audio2 input terminal

AV COMPONENT (D-SUB)

AV VIDEO (D-SUB)

Audio input terminal

PC HDMI

AV HDMI

PC/AV HDMI input terminal

PC/AV HDMI input terminal

n

Use a commercially available HDMI cable (conforming to the HDMI standard).

n

Set HDMI of INPUT SELECT on the OPTION menu according to the device to be connected.

n

Select the audio input terminal to be used in PC HDMI or AV HDMI of AUDIO SELECT on the

OPTION menu. 

When HDMI is selected, connection to the audio input terminal is unnecessary.

PC D-SUB input terminal

n

Set D-SUB of INPUT SELECT on the OPTION menu according to the device to be connected.

n

Common terminal for AV COMPONENT and AV VIDEO.

n

When the PN-ZB02 (optional) is attached, select the audio input terminal to be used in PC D-SUB of

AUDIO SELECT on the OPTION menu.

n

To use with AV VIDEO (D-SUB), connect the green terminal to the device’s video output.

Audio input terminal

n

Use an audio cable without resistance.

n

When the PN-ZB02 (optional) is attached, set the audio input terminal used for each input mode in

AUDIO SELECT on the OPTION menu.

Audio output terminals

n

The output sound varies depending on the input mode.

n

The volume of the output sound can be fixed by setting AUDIO OUTPUT(RCA) on the OPTION
menu.

n

It is not possible to control the sound output from the audio output terminals with the AUDIO menu.

RS-232C input terminal

RS-232C output terminal

n

You can control the monitor from a PC by connecting a commercially available RS-232 straight cable
between these terminals and the PC.

n

When using the PN-ZR01 control kit (optional) to perform operation of multiple monitors with the

remote control unit, connect multiple monitors in a daisy chain using the commercially available RS-
232 straight cable.

PN-V602　INSTALLATION, ADJUSTMENT, SETTING

 2 – 3

■ CONNECTION WHEN THE PN-ZB02 (OPTIONAL) IS ATTACHED

The PN-ZB02 expansion board (optional) allows the use of additional connection terminals.

You can control the monitor from a PC on a network by connecting a commercially available LAN cable between this terminal and a network.

n

The video of the PC/AV DVI-D input can be output to an external device.

n

Outputting HDCP-encrypted video requires an external device which supports HDCP.

n

This terminal allows the daisy chain connection of up to 5 monitors.

n

The length of the signal cables or surrounding environment may

affect the image quality.

n

The screen may not display properly when using terminals other
than “PC DVI-D”/“AV DVI-D” for the input mode. In this case, turn

off the power to all the monitors connected in a daisy chain and

then turn the power on again.

n

When connecting monitors in a daisy chain set “AUTO INPUT
CHANGE” to “OFF”.

n

Video output is disabled in the following cases.

---When the input mode is “PC HDMI”/“AV HDMI”.

---When PIP SOURCE of the PIP/PbyP menu is set to PC

“HDMI” or “AV HDMI”.

---When the power is turned “off”.

---When the monitor is in input signal waiting mode.

PC/AV DVI-D input terminal

n

Set DVI of INPUT SELECT on the OPTION menu according to the device to be connected.

n

Select the audio input terminal to be used in PC DVI-D or AV DVI-D of AUDIO SELECT on the

OPTION menu.

PC RGB input terminals

n

Set BNC of INPUT SELECT on the OPTION menu to PC RGB when using the PC RGB input terminals.

n

Select the audio input terminal to be used in PC RGB of AUDIO SELECT on the OPTION menu.

AV component input 

terminals

n

Set BNC of INPUT SELECT on the OPTION menu to AV COMPONENT when using the AV compo-

nent input terminals.

n

Select the audio input terminal to be used in AV COMPONENT of AUDIO SELECT on the OPTION menu.

n

Cannot be used when D-SUB in INPUT SELECT on the OPTION menu is set to AV COMPONENT.

AV S-video input terminal

n

Select the audio input terminal to be used in AV S-VIDEO of AUDIO SELECT on the OPTION menu.

AV video input terminal

n

Select the audio input terminal to be used in AV VIDEO of AUDIO SELECT on the OPTION menu.

n

Cannot be used when D-SUB in INPUT SELECT on the OPTION menu is set to AV VIDEO.

Audio1 input terminals/

 Audio2 input terminals

n

Set the audio input terminal to be used in each input mode in AUDIO SELECT on the OPTION menu.

H

V

R

G

B

Cr/Pr

Y

Cb/Pb

First monitor

Second monitor

Digital signal (DVI) cables
(commercially available)

To PC digital RGB output terminal

shows the signal flow

PC/AV DVI-D 
output terminal

PC/AV DVI-D 
input terminals

PC/AV DVI-D 
output terminals