Sharp PN-Y555 (serv.man4) User Manual / Operation Manual ▷ View online
41
E
The Power LED is flashing in red and green alternately.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight decreases
automatically in order to prevent high-temperature-related
problems. When this occurs, the Power LED flashes red
and green alternately.
automatically in order to prevent high-temperature-related
problems. When this occurs, the Power LED flashes red
and green alternately.
• If the internal temperature rises further, the monitor
automatically enters standby mode. (The Power LED
continues flashing red and green alternately.)
continues flashing red and green alternately.)
• Remove the cause of the excessive temperature rise.
- If the monitor enters standby mode due to a rise in
temperature, to return to normal display, turn the power
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated. (See page 8.)
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated. (See page 8.)
- Check whether the monitor is placed at a location where
a quick rise in temperature is likely. Internal temperature
rises quickly if the vents on the monitor are blocked.
rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates
inside the monitor or around the vents. Remove dust if
possible. Ask SHARP dealer about removing internal dust.
possible. Ask SHARP dealer about removing internal dust.
Troubleshooting
42
E
Specifications
n
Product Specifications
Model
PN-Y555
PN-Y475
PN-Y425
LCD component
55" Class [54-5/8 inch
(138.8cm) diagonal]
TFT LCD
47" Class [46-15/16 inch
(119.3cm) diagonal]
TFT LCD
42" Class [42 inch
(106.7cm) diagonal]
TFT LCD
Max. resolution
(pixels)
1920 x 1080
Max. colors
Approx. 1.06 billion colors
Pixel pitch
0.630 mm (H) ×
0.630 mm (V)
0.542 mm (H) ×
0.542 mm (V)
0.485 mm (H) ×
0.485 mm (V)
Viewing angle
178° right/left/up/down (contrast ratio ≥ 10)
Screen active area
inch (mm)
47-5/8 (W) x 26-13/16 (H)
(1209.6 x 680.4)
40-15/16 (W) x 23 (H)
(1039.7 x 584.8)
36-5/8 (W) x 20-5/8 (H)
(930.2 x 523.3)
Computer input signal
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω]
Sync signal
Horizontal/vertical separate (TTL: positive/negative)
Video color system
NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input terminals
PC/AV
HDMI x 1
PC
Mini D-sub 15 pin, 3 rows x 1
DVI-D 24 pin (HDCP compatible) x 1
Audio
3.5 mm mini stereo jack x 1
RCA pin (L/R) x 1
Serial (RS-232C)
D-sub 9 pin x 1
USB flash drive
x 1
Output
terminals
PC
DVI-D 24 pin (HDCP compatible) x 1
Audio
RCA pin (L/R) x 1
Serial (RS-232C)
D-sub 9 pin x 1
LAN terminal
10 BASE-T/100 BASE-TX
Speaker output
7 W + 7 W
Power requirement
AC 100 - 240 V, 1.7 A,
50/60 Hz
AC 100 - 240 V, 1.5 A,
50/60 Hz
AC 100 - 240 V, 1.4 A,
50/60 Hz
Operating temperature *
1
32°F to 104°F (0°C to 40°C)
Operating humidity
20% to 80% (no condensation)
Power consumption
(Input signal waiting mode / standby mode *
2
)
150 W (16 W / 16 W)
135 W (16 W / 16 W)
120 W (16 W / 16 W)
Dimensions (excluding protrusions) inch (mm)
Approx. 49-3/16 (W) x
2-5/8 (D) x 28-5/16 (H)
(1249 x 66 x 719)
Approx. 42-3/8 (W) x
2-5/8 (D) x 24-1/2 (H)
(1077 x 66 x 622)
Approx. 38-1/8 (W) x
2-5/8 (D) x 22-1/16 (H)
(968 x 66 x 561)
Weight
lbs. (kg)
Approx. 55.2 (25.0)
Approx. 36.4 (16.5)
Approx. 32.0 (14.5)
*1
Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP.
In such cases, please check the temperature condition specified by the optional equipments.
*2
When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
43
E
Specifications
n
Dimensional Drawings
Note that the values shown are approximate values.
Unit: inch [mm]
7-7/8
[200]
15-3/
4
[400]
VESA holes *
7-7/8
[200]
Opening width (47-15/16 [1217])
Opening height
(27-1/16 [687]
)
28-5/16 [719
]
49-3/16 [1249]
1-7/16
[37]
2-5/8
[66]
Opening width (41-1/8 [1045])
Opening height (23-1/4 [590])
24-1/2 [622
]
42-3/8 [1077]
1-7/16
[37]
2-5/8
[66]
Opening width (36-7/8 [936])
Opening height (20-13/16 [529]
)
22-1/16 [561]
38-1/8 [968]
1-7/16
[37]
2-5/8
[66]
7-7/8
[200]
7-7/8
[200]
15-3/
4
[400]
VESA holes *
7-7/8
[200]
7-7/8
[200]
15-3/
4
[400]
VESA holes *
[PN-Y555]
[PN-Y475]
[PN-Y425]
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times
or more the weight of the monitor.
44
E
n
Power management
This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in
order for the monitor’s power management function to work.
DPMS: Display Power Management Signaling
DPMS
Screen
Power
consumption* Hsync
Vsync
ON STATE
Display
150 W
Yes
Yes
135 W
120 W
120 W
STANDBY
No
display
16 W
No
Yes
SUSPEND
16 W
Yes
No
OFF STATE
16 W
No
No
DMPM: Digital Monitor Power Management
DMPM
Screen
Power
consumption*
Monitor ON
Display
150 W
135 W
120 W
135 W
120 W
Active OFF
No display
16 W
16 W
16 W
16 W
16 W
* Values of the PN-Y555, PN-Y475, and PN-Y425 in that order from the top.
n
DDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters
is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect
plug-and-play monitors.
There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
Specifications
Click on the first or last page to see other PN-Y555 (serv.man4) service manuals if exist.