Sharp PN-E802 (serv.man3) Service Manual ▷ View online
CHAPTER 1. OUTLINE OF THE PRODUCT
PN-E802/E702/E602 OUTLINE OF THE PRODUCT
1 – 5
1 - 4. COMPATIBLE SIGNAL TIMING (AV)
*
1
Available when the PN-ZB01 (optional) is attached.
1 - 5. POWER MANAGEMENT
This monitor conforms to VESA DPMS and DVI DMPM. Both your video
card and computer must support the same standard in order for the
card and computer must support the same standard in order for the
monitor’s power management function to work.
DPMS: DISPLAY POWER MANAGEMENT SIGNALING
DMPM: DIGITAL MONITOR POWER MANAGEMENT
*
The power consumption is the value when the display is not
equipped with the PN-ZB01 (optional).
*
1
When “AUTO INPUT CHANGE” is set to “OFF”.
1 - 6. DDC (PLUG AND PLAY)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and com-
DDC is a signal standard for plug and play between monitors and com-
puters. Information about resolution and other parameters is exchanged
between the two. This function can be used if the computer supports
DDC and it has been configured to detect plug-and-play monitors.
DDC and it has been configured to detect plug-and-play monitors.
There are several types of DDC, depending on the communication
method used. This monitor supports DDC2B.
1 - 7. SUPPLIED ACCESSORIES
Screen resolution
Frequency
DVI-D
*1
HDMI
Component
*1
1920 x 1080p
24Hz
---
Yes
---
50Hz
Yes
Yes
Yes
59.94Hz
Yes
Yes
Yes
60Hz
Yes
Yes
Yes
1920 x 1080i
50Hz
Yes
Yes
Yes
59.94Hz
Yes
Yes
Yes
60Hz
Yes
Yes
Yes
1280 x 720p
50Hz
Yes
Yes
Yes
59.94Hz
Yes
Yes
Yes
60Hz
Yes
Yes
Yes
720 x 576p
50Hz
Yes
Yes
Yes
720 x 480p
59.94Hz
Yes
Yes
Yes
60Hz
Yes
Yes
Yes
640 x 480p (VGA)
59.94Hz
Yes
Yes
---
60Hz
Yes
Yes
---
720 (1440) x 576i
50Hz
---
Yes
Yes
720 (1440) x 480i
59.94Hz
---
Yes
Yes
60Hz
---
Yes
Yes
DPMS
Screen
Power
consumption
*
Hsync
Vsync
ON STATE
Display
PN-E802: 265W
PN-E702: 235W
PN-E602: 165W
PN-E602: 165W
Yes
Yes
STANDBY
No
display
1.0W
*1
No
Yes
SUSPEND
Yes
No
OFF STATE
No
No
DMPM
Screen
Power
consumption
*
Monitor ON
Display
PN-E802: 265W
PN-E702: 235W
PN-E602: 165W
PN-E602: 165W
Active OFF
No display
1.0W
*1
* Place this sticker onto the SHARP logo to cover the logo.
Remote control unit: 1
Power cord: 1
R-6 battery ("AA" size): 2
CD-ROM (Utility Disk for Windows): 1
Setup Manual: 1
Vertical sticker (Operation panel): 1
Vertical sticker (Logo): 1
Terminal label: 1
Vertical sticker (Logo): 1
Terminal label: 1
Cover Sharp logo: 1
Cover: 2 (PN-E802)
Cover screws (M4 with washers): 4 (PN-E802)
Cover screws (M4 with washers): 4 (PN-E802)
Cable clamp: 2
* Sharp Corporation holds authorship rights to the Utility Disk
program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the
disposal instructions for your area.
disposal instructions for your area.
(Used when installing the interface expansion board PN-ZB01
(optional).)
(optional).)
CHAPTER 1. OUTLINE OF THE PRODUCT
PN-E802/E702/E602 OUTLINE OF THE PRODUCT
1 – 6
1 - 8. LAYOUT OF TERMINAL PINS
■ PC/AV DVI-D INPUT TERMINAL PINS
■ RS-232C INPUT TERMINAL PINS
■ RS-232C OUTPUT TERMINAL PINS
■ PC D-SUB INPUT TERMINAL PINS
■ PC/AV DVI-D OUTPUT TERMINAL PINS
■ PC/AV HDMI INPUT TERMINAL PINS
No.
Function
No.
Function
1
TMDS data 2-
13
N.C.
2
TMDS data 2+
14
+5V
3
TMDS data 2/4 shield
15
GND
4
N.C.
16
Hot-plug detection
5
N.C.
17
TMDS data 0-
6
DDC clock
18
TMDS data 0+
7
DDC data
19
TMDS data 0/5 shield
8
N.C.
20
N.C.
9
TMDS data 1-
21
N.C.
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
No.
Function
No.
Function
1
N.C.
6
N.C.
2
Transmitted data
7
N.C.
3
Received data
8
N.C.
4
N.C.
9
N.C.
5
GND
No.
Function
No.
Function
1
N.C.
6
N.C.
2
Received data
7
N.C.
3
Transmitted data
8
N.C.
4
N.C.
9
N.C.
5
GND
(DVI-D 24 PIN)
(D-SUB 9 PIN)
(D-SUB 9 PIN)
No.
Function
No.
Function
1
Red video signal input
9
+5V
2
Green video signal input
10
GND
3
Blue video signal input
11
N.C.
4
N.C.
12
DDC data
5
GND
13
Hsync signal input
6
GND for red video signal
14
Vsync signal input
7
GND for green video signal
15
DDC clock
8
GND for blue video signal
No.
Function
No.
Function
1
TMDS data 2-
13
N.C.
2
TMDS data 2+
14
+5V
3
TMDS data 2/4 shield
15
GND
4
N.C.
16
Hot-plug detection
5
N.C.
17
TMDS data 0-
6
DDC clock
18
TMDS data 0+
7
DDC data
19
TMDS data 0/5 shield
8
N.C.
20
N.C.
9
TMDS data 1-
21
N.C.
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
No.
Function
No.
Function
1
TMDS data 2+
11
TMDS clock shield
2
TMDS data 2 shield
12
TMDS clock-
3
TMDS data 2-
13
CEC
4
TMDS data 1+
14
N.C.
5
TMDS data 1 shield
15
SCL
6
TMDS data 1-
16
SDA
7
TMDS data 0+
17
DDC/CEC GND
8
TMDS data 0 shield
18
+5V
9
TMDS data 0-
19
Hot-plug detection
10
TMDS clock+
(Mini D-SUB 15 PIN)
(DVI-D 24 PIN)
(HDMI CONNECTOR)
TM
CHAPTER 1. OUTLINE OF THE PRODUCT
PN-E802/E702/E602 OUTLINE OF THE PRODUCT
1 – 7
2. PART NAMES AND FUNCTION
2 - 1. DISPLAY
■ FRONT VIEW
<PN-E802>
<PN-E702>
<PN-E602>
REFERENCE CHART OF POWER LED5 LIGHTING STATUS
CAUTION
n
When switching the main power switch or the POWER button off
and back on, always wait for at least 5 seconds.
and back on, always wait for at least 5 seconds.
A short interval may result in a malfunction.
MEMO
n
When the main power switch is off, the monitor cannot be turned
on.
n
If the monitor is in the input signal standby mode and you press
the POWER button on the remote control unit, the monitor enters
standby mode.
standby mode.
n
Setting the SCHEDULE flashes the power LED alternately in red
and orange in standby mode.
n
To disable the logo screen from displaying when turning the
power ON, set LOGO SCREEN to OFF on the SETUP menu.
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
LCD panel
2
Remote control sensor
3
Input switch
4
Power switch
5
Power LED
Lighting Status
Status Description
Green lamp is lit.
Power on
Green lamp is flashing.
Input signal waiting mode
Orange lamp is lit.
Power off (Standby mode)
CHAPTER 1. OUTLINE OF THE PRODUCT
PN-E802/E702/E602 OUTLINE OF THE PRODUCT
1 – 8
■ REAR VIEW
<PN-E802>
<PN-E702>
<PN-E602>
*
1
This section is used to connect optional attachments for function
expansion.
*
2
The connection terminals can be added by attaching the PN-
ZB01 expansion board (optional).
*
3
This terminal is used to connect optional parts for function
expansion.
expansion.
CAUTION
n
Consult your SHARP dealer for attachment/detachment of
optional parts.
n
Do not open the expansion terminal cover by yourself.
There are high voltage parts inside the cover which may cause
There are high voltage parts inside the cover which may cause
an electric shock.
WHEN THE PN-ZB01 (OPTIONAL) IS ATTACHED
1
2
3
3
4
5
6
7
8
9
9
F
H
H
G
K
L
M
N
O
P
Q
S
T
S
T
R
I
J
When the PN-ZB01
(optional) is attached
(optional) is attached
1
2
3
4
5
I
J
When the PN-ZB01
(optional) is attached
(optional) is attached
6
7
8
9
9
F
H
H
G
K
L
M
N
O
P
Q
S
T
S
T
R
1
2
3
4
I
J
When the PN-ZB01
(optional) is attached
(optional) is attached
5
6
7
8
9
9
F
H
H
G
K
L
M
N
O
P
Q
S
T
S
T
R
1 Optional attachment section
*1
8 Audio input terminal
2 Handles
9 Audio output terminals
3 Vents
F RS-232C output terminal
4 Speakers
G RS-232C input terminal
5 Expansion terminal cover
*2
H Optional terminal
*3
6 PC/AV HDMI input terminal
I AC input terminal
7 PC D-SUB input terminal
J Main power switch
K PC/AV DVI-D input terminal
P Audio 2 input terminals
L PC/AV DVI-D output terminal
Q PC RGB input terminals
M LAN terminal
R AV component input terminals
N External speaker terminals
S AV video input terminal
O Audio 1 input terminals
T AV S-video input terminal
Click on the first or last page to see other PN-E802 (serv.man3) service manuals if exist.