Sharp PN-E802 (serv.man3) Service Manual ▷ View online
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
PN-E802/E702/E602 INSTALLATION, ADJUSTMENT, SETTING
2 – 4
■ CONNECTION WITH A PC OR AV EQUIPMENT
■ CONNECTION WHEN THE PN-ZB01 (OPTIONAL) IS ATTACHED
The PN-ZB01 expansion board (optional) allows the use of additional connection terminals.
<LAN TERMINAL>
You can control the monitor from a PC on a network by connecting a commercially available LAN cable between this terminal and a network.
Video
input
PC/AV HDMI input terminal
n
Use a commercially available HDMI cable (conforming to the HDMI standard).
n
Set HDMI of INPUT SELECT on the OPTION menu according to the device to be connected.
n
Select the audio input terminal to be used in PC HDMI or AV HDMI of AUDIO SELECT on the
OPTION menu.
When HDMI is selected, connection to the audio input terminal is unnecessary.
PC D-SUB input terminal
n
Set D-SUB of INPUT SELECT on the OPTION menu according to the device to be connected.
n
Common terminal for AV COMPONENT and AV VIDEO.
n
When the PN-ZB01 (optional) is attached, select the audio input terminal to be used in PC D-SUB of
AUDIO SELECT on the OPTION menu.
n
To use with AV VIDEO (D-SUB), connect the green terminal to the device’s video output.
Audio
input/
output
Audio input terminal
n
Use an audio cable without resistance.
n
When the PN-ZB01 (optional) is attached, set the audio input terminal used for each input mode in
AUDIO SELECT on the OPTION menu.
Audio output terminals
n
The output sound varies depending on the input mode.
n
The volume of the output sound can be fixed by setting AUDIO OUTPUT(RCA) on the OPTION
menu.
menu.
n
It is not possible to control the sound output from the audio output terminals with the AUDIO menu.
Monitor
control
RS-232C input terminal
RS-232C output terminal
n
You can control the monitor from a PC by connecting a commercially available RS-232 straight cable
between these terminals and the PC.
between these terminals and the PC.
Video
input
PC/AV DVI-D input terminal
n
Set DVI of INPUT SELECT on the OPTION menu according to the device to be connected.
n
Select the audio input terminal to be used in PC DVI-D or AV DVI-D of AUDIO SELECT on the
OPTION menu.
PC RGB input terminals
n
Set BNC of INPUT SELECT on the OPTION menu to PC RGB when using the PC RGB input terminals.
n
Select the audio input terminal to be used in PC RGB of AUDIO SELECT on the OPTION menu.
AV component input
terminals
n
Set BNC of INPUT SELECT on the OPTION menu to AV COMPONENT when using the AV compo-
nent input terminals.
n
Select the audio input terminal to be used in AV COMPONENT of AUDIO SELECT on the OPTION menu.
n
Cannot be used when D-SUB in INPUT SELECT on the OPTION menu is set to AV COMPONENT.
AV S-video input terminal
n
Select the audio input terminal to be used in AV S-VIDEO of AUDIO SELECT on the OPTION menu.
AV video input terminal
n
Select the audio input terminal to be used in AV VIDEO of AUDIO SELECT on the OPTION menu.
n
Cannot be used when D-SUB in INPUT SELECT on the OPTION menu is set to AV VIDEO.
Audio
input
Audio1 input terminals/
Audio2 input terminals
n
Set the audio input terminal to be used in each input mode in AUDIO SELECT on the OPTION menu.
H
V
R
G
B
Cr/Pr
Y
Cb/Pb
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
PN-E802/E702/E602 INSTALLATION, ADJUSTMENT, SETTING
2 – 5
<PC/AV DVI-D OUTPUT TERMINAL>
n
The video of the PC/AV DVI-D input can be output to an external
device.
n
Outputting HDCP-encrypted video requires an external device which
supports HDCP.
n
This terminal allows the daisy chain connection of up to 5 monitors.
MEMO
n
The length of the signal cables or surrounding environment may
affect the image quality.
n
The screen may not display properly when using terminals other
than “PC DVI-D”/“AV DVI-D” for the input mode. In this case, turn
than “PC DVI-D”/“AV DVI-D” for the input mode. In this case, turn
off the power to all the monitors connected in a daisy chain and
then turn the power on again.
n
When connecting monitors in a daisy chain set “AUTO INPUT
CHANGE” to “OFF”.
CHANGE” to “OFF”.
n
Video output is disabled in the following cases.
---When the power is turned “off”.
---When the monitor is in input signal waiting mode.
<EXTERNAL SPEAKER TERMINALS>
n
To use an external speaker, set “SPEAKER SELECT” on the SETUP
menu to “EXTERNAL”.
menu to “EXTERNAL”.
n
Be sure to use external speakers with an impedance of 6
Ω and a
rated input of at least 7 W.
1 ) Attach a speaker cable core (included with the PN-ZB01) to the
end of the speaker cable connected to the monitor.
2 ) While pushing the tab, insert the tip of the cable.
3 ) Release the tab.
CAUTION
n
Be sure to connect the + and - terminals and the left and right
speakers properly.
speakers properly.
n
Avoid short circuiting the + and - terminals.
n
When “SPEAKER SELECT” is set to “EXTERNAL”, the internal
speaker is disabled.
First monitor
Second monitor
Digital signal (DVI) cables
(commercially available)
(commercially available)
To PC digital RGB output terminal
shows the signal flow
PC/AV DVI-D
output terminal
output terminal
PC/AV DVI-D
input terminals
input terminals
PC/AV DVI-D
output terminals
output terminals
Example
Approx.
3-15/16 inch
(10 cm)
3-15/16 inch
(10 cm)
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
PN-E802/E702/E602 INSTALLATION, ADJUSTMENT, SETTING
2 – 6
■ CONTROLLING THE MONITER WITH A PC
(RS-232C)
You can control this monitor from a PC via RS-232C (COM port) on the
PC.
You can also connect multiple monitors via a daisy chain by using a PC.
By assigning ID numbers to each monitor (see page 19), you can make
By assigning ID numbers to each monitor (see page 19), you can make
input mode selection/adjustment or can check the status of a specific
monitor.
You can also connect multiple monitors via a daisy chain by using a PC.
By assigning ID numbers to each monitor, you can make input mode
By assigning ID numbers to each monitor, you can make input mode
selection/adjustment or can check the status of a specific monitor.
CAUTION
PRECAUTIONS WHEN THE PN-ZB01 (OPTIONAL) IS
ATTACHED
ATTACHED
n
To control the monitor via RS-232C, set RS-232C/LAN SELECT
to RS-232C.
n
You cannot use RS-232C and LAN control simultaneously.
<ONE-TO-ONE CONNECTION WITH A PC>
Connect with RS-232 straight cable between the PC's COM port (RS-
232C connector) and the RS-232C input terminal on the monitor.
232C connector) and the RS-232C input terminal on the monitor.
<DAISY CHAIN CONNECTION [ADVANCED OPERATION]>
Connect with RS-232 straight cable between the PC's COM port (RS-
232C connector) and the RS-232C input terminal on the first monitor.
232C connector) and the RS-232C input terminal on the first monitor.
Next, connect RS-232 straight cable to the first monitor's RS-232C out-
put terminal and to the second monitor's RS-232C input terminal. Con-
nect in the same way to the third and subsequent monitors.
Up to 25 monitors can be connected. (Depending on the length of the
cable used and the surrounding environment.)
cable used and the surrounding environment.)
<COMMUNICATION CONDITIONS>
Set the RS-232C communication settings on the PC to match the moni-
tor's communication settings as follows.
*
1
Set to the same baud rate as the “BAUD RATE” setting of
SETUP menu.
SETUP menu.
When connecting multiple monitors in a daisy chain, set all mon-
itors to the same “BAUD RATE”.
RS-232C input
terminal
terminal
RS-232 straight cable
(commercially available)
(commercially available)
To COM port
PC
Baud rate
38400 bps (Initial setting)
*1
Data length
8 bits
Parity bit
None
Stop bit
1 bit
Flow control
None
First monitor
Second monitor
RS-232C
output terminal
output terminal
RS-232C
input terminal
input terminal
RS-232 straight cables
(commercially
available)
(commercially
available)
To COM port
PC
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
PN-E802/E702/E602 INSTALLATION, ADJUSTMENT, SETTING
2 – 7
■ CONTROLLING THE MONITOR WITH A PC
(LAN)
When the PN-ZB01 (optionel) is a attached, your monitor can be con-
nected to a LAN allowing you to control it from a PC on the LAN.
You can also configure the monitor to send e-mail notification when it
has a problem.
has a problem.
The connection requires a commercially available LAN cable (UTP
cable, Category 5, straight through).
MEMO
n
You must assign an IP address to the monitor by following the
procedures in “Settings to connect to a LAN”.
n
Your PC must be installed with Internet Explorer (version 7.0 or
later).
n
To control the monitor via LAN, set RS-232C/LAN SELECT to
LAN.
LAN.
n
You cannot use RS-232C and LAN control simultaneously.
CAUTION
INITIALIZING PERSONAL INFORMATION
n
When the PN-ZB01 (optional) is attached, personal information
such as e-mail addresses can be registered in the monitor.
Before transferring or disposing of the monitor, initialize all set-
tings by selecting “ALL RESET1”. Note that “ALL RESET2” will
tings by selecting “ALL RESET1”. Note that “ALL RESET2” will
not initialize e-mail addresses and other settings.
1 - 2.
CONNECTING THE POWER CORD
CAUTION
n
Do not use a power cord other than the one supplied with the
monitor.
1 ) Turn off the main power switch.
2 ) Plug the power cord (supplied) into the AC input terminal.
3 ) Plug the power cord (supplied) into the AC power outlet.
LAN terminal
LAN cable (commercially available, straight)
Network (LAN)
Hub
1
Main power switch
AC input
terminal
terminal
2
3
Power cord (Supplied)
For power
outlet
outlet
Click on the first or last page to see other PN-E802 (serv.man3) service manuals if exist.