DOWNLOAD Sharp LL-T15S1 (serv.man11) Service Manual ↓ Size: 1.41 MB | Pages: 113 in PDF or view online for FREE

1

7

8

9

10

11 12 13

14

15

2

3

4 5 6

1.

MENU button .......................... This button is used to pop-up, select and close the OSD Menu.

2.

SELECT button ....................... When the On Screen Display (OSD) menu is displayed, choose the menu option to

be adjusted.

3.

   

buttons ............................ When the OSD menu is displayed:

Change or adjust the adjustment values by switching between the OSD options
contents.

When the backlight adjustment bar is displayed:

The brightness of the backlight can be adjusted.

When the OSD menu / backlight adjustment bar is not displayed:

The speaker volume can be adjusted.

4.

BRIGHT button ....................... When the OSD menu is displayed:

The OSD menu disappears.

When the OSD menu is not displayed:

Switch between turning the automatic brightness adjustment function [ON] and
[OFF].

5.

Power LED .............................. This LED is lit green when in use and orange when in power-saving mode.

6.

Power  button ........................... Pressing this button turns the power on. (After turning the power on, it may take a

little time before the screen displays.)
Press the button again to turn the power off.

7.

Speakers ................................ Audio entering via the monitor and the external device connected to the monitor

can be heard.

8.

Brightness sensor .................. Measures the brightness of the surrounding environment.

9.

Microphone terminal .............. A microphone (to be purchased separately) can be connected here.

10. Headphone terminal .............. Headphones (to be purchased separately) can be connected here.
11. Audio input terminal ............... A computer’s audio output terminal can be connected here. (The audio cable

included should be used.)

12. Microphone output terminal ... A computer’s microphone terminal can be connected here. (The audio cable

included should be used.)

13. Power terminal ........................ Connect the AC adapter (included) here.
14. RGB signal cable ................... Connects to the computer's analog RGB output terminal.
15. Ventilation openings .............. Note: Never block the ventilation openings as this may lead to overheating inside

the monitor and result in malfunction.

Standing up the monitor
Press down on the stand and lift up the top section of the
monitor.

Adjusting the monitor
Lightly holding both sides of the monitor, adjust it to a
suitable viewing angle.

25

3

Except when folding away the monitor to transport it,
do not fold down the monitor. Unnecessarily folding
and unfolding the monitor could lead to malfunction.

1. Remove the AC adapter.
2. If carrying out adjustments to the monitor, place it

upright.

3. While pressing the rear lock disable button (1),

gently fold back the monitor (2).

(2)

(1)

When connecting, ensure that both the monitor and
computer are switched off.

Do not overly bend the cable or add extension cords
as this could lead to malfunction.

Using the audio cable included, the computer’s audio
output terminal or a microphone terminal can be con-
nected.

 

 

DO only connect cables less than 3m to the LL-
T15S1.

RGB cable

If connecting to a D-sub 15 pin 2 row Apple
Power Macintosh, attach a Macintosh
conversion adapter (to be purchased
separately) to the RGB signal cable.

Macintosh conversion adapter

RGB signal cable
After connecting the adapter, tighten the
screws on each side to fix into place.

Firmly insert the analog RGB output
terminal (mini D-sub 15 pin with 3 rows)
then tighten the screws each side.

Headphones and a microphone (both to be purchase
separately) can be connected here.

Do not overly bend the cable or add extension cords
as this could lead to malfunction.

DO only connect cables less than 3m to the LL-
T15S1.

When the headphones are connected, no sound can
be heard from the monitor speakers.

Before connecting, first turn off the monitor's main
power switch.

Do not overly bend the cable or add extension cords
as this could lead to malfunction.

1. Connect the AC adapter to the monitor's power

terminal

   

2. Attach the power cord to the AC adapter and place

the power plug into the AC terminal.

   

Audio cable

Audio input
terminal

Microphone output
terminal

PC (Audio output
terminal)

PC (Microphone
terminal)

Microphone
terminal

Headphone
terminal

Microphone

Headphones

Power terminal

AC adapter

Power cord

1. Turn on the computer.
2. Press the monitor's power button.

The power LED will be lit green, and the screen will
display an image.

When setting up this monitor for the first time or after
having changed an aspect of the current system,
perform an automatic screen adjustment before use
(p. 15).

1. Turn the computer off.
2. Press the monitor's power button.

The Power LED will disappear.

Depending on the computer or OS, it may be necessary
to use the computer to operate the installation of monitor
set-up information etc. If so, follow the steps below to
install the monitor set-up information. (Depending on the
type of computer or OS, command names and methods
may differ. Please follow the computer’s own operation
manual while reading this.)

For Windows95
Installing monitor set-up information into Windows95.
This explanation assumes that the floppy disk drive is "A
drive".

1. Place the Utility Disk (provided) into the computer's A

drive.

2. Click on the [Start] button. From [Settings], choose

[Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced Properties], and

[Monitor], then [Change].

5. Click on [Have disk], confirm that [Copy manufactur-

er's files from:] is [A:] then click [OK].

6. Confirm that the monitor details are selected, and

click [OK].

7. Check that the monitor details are displayed, then

click [Apply].

8. Click [OK], and close the window.

9. Remove the Utility Disk from the A drive.

For Windows98
Installing monitor set-up information into Windows98.
This explanation assumes that the floppy disk drive is "A
drive".

If the "Add new Hardware Wizard" has appeared:

1. Place the Utility Disk (provided) into the computer's A

drive.

2. Click [Next].

3. Check [Display a list of all the drivers in a specific

location, so you can select the driver you want.], then
click [Next].

4. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is [A:],
and click [OK].

5. Confirm that the monitor details are selected, then

click [Next], [Next], and [Finish]. If the "Add New
Hardware Wizard" appears, repeat the installation
commands beginning from 2 above.

6. Remove the Utility Disk from the A drive.

If the "Add New Hardware Wizard" has not appeared:

1. Place the Utility Disk in the computer's A drive.

2. Click on the [Start] button. From [Settings], choose

[Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. In [Options], check [Automatically detect Plug & Play

monitors] and click on [Change].

6. Click [Next].

7. Click on [Display a list of all the drivers in a specific

location, so you can select the driver you want.], then
click [Next].

8. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is [A:],
and click [OK].

9. Confirm that the monitor details are selected, then

click [Next], [Next], and [Finish].

10. Check that the monitor details are displayed, then

click [Apply].

11. Click [OK], and close the window.

12. Remove the Utility Disk from the A drive.

Power LED

Power button