DOWNLOAD Sharp MX-FNX2 (serv.man10) Service Manual ↓ Size: 192.76 KB | Pages: 2 in PDF or view online for FREE

Model
MX-FNX2 (serv.man10)
Pages
2 Few pages! See other manuals at the bottom of the first or last page.
Size
192.76 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Section 8 - Adjustments .
File
mx-fnx2-sm10.pdf
Date

Sharp MX-FNX2 (serv.man10) Service Manual ▷ View online

MX-FNX2/AR-PN1/MX-RBX1  ADJUSTMENTS  8 – 1
âºíuÇ´
Service Manual
 
[8] ADJUSTMENTS
1. Finisher/saddle unit
A. Adjusting the Folding Position
The folding position is adjusted by matching it with the stapling
position.
If you have replaced the finisher controller PCB, you must transfer
the existing settings to the new PCB. Perform the following if the
folding position must be adjusted for some reason.
NOTE: Both the folding and stapling positions may deviate for
some type of paper. In such a case, change the "middle
stapling position" in the user mode of the host machine.
1)
Set SW1 on the finisher controller PCB as follows:
2)
Adjust the folding position by pressing the PSW1 or PSW2 on
the finisher controller PCB a required number of times. Press-
ing the switch once moves the folding position about 0.16 mm.
• To move the folding position in the "-" direction, press the
PSW1.
• To move the folding position in the "+" direction, press the
PSW2.
• Pressing the PSW1 and PSW2 at the same time clears the
adjustment value.
3)
When adjustment of the folding position is complete, set all bits
of the SW1 on the finisher controller PCB to OFF.
4)
Enter the bind mode of the host machine and check whether
the folding position is adjusted properly. If adjusted improperly,
adjust the folding position again.
B. Adjusting the Middle 2-Point Stapling Position
The stapling position is adjusted by matching it with the folding
position.
 This adjustment is necessary:
• If you have replaced the finisher controller PCB.
• If the stapling position must be adjusted for some reason.
NOTE: Both the folding and stapling positions may deviate for
some type of paper. In such a case, change the "middle
stapling position" in the user mode of the host machine.
1)
Set SW1 on the finisher controller PCB as follows:
2)
Adjust the stapling position by pressing the PSW1 or PSW2 on
the finisher controller PCB a required number of times. Press-
ing the switch once moves the stapling position about 0.14
mm.
• To move the stapling position in the "-" direction, press the
PSW1.
• To move the stapling position in the "+" direction, press the
PSW2.
• Pressing the PSW1 and PSW2 at the same time clears the
adjustment value.
3)
When adjustment of the stapling position is complete, set all
bits of the SW1 on the finisher controller PCB to OFF.
4)
Enter the bind mode of the host machine and check whether
the stapling position is adjusted properly. If adjusted improp-
erly, adjust the stapling position again.
C. One-page exit mode
This mode is used to increase the accuracy of paper alignment in
the simple load offset mode by discharging paper one by one to the
offset tray.
1)
Set the SW1 of the finisher control PWB as shown below.
2)
Turn on the power.
2. Punch unit (option)
A. Adjusting the Punch Hole Position
This adjustment is available only in the diagnostic mode (Sim 3-10)
of the host machine. The range of punch hole displacement is
between 3 and -3 in 1-mm increments. A higher setting will move
the punch hole toward the leading edge of sheet.
B. Adjusting the Sensor Output
Perform the following when the punch controller PCB, horizontal
registration sensor (photosensor PCB/LED PCB), or waste full sen-
sor (waste full photosensor PCB/waste full LED PCB) has been
replaced.
1)
Shift bits 1 through 4 on the punch controller PCB as follows:
2)
Press SW1002 or SW1003 on the punch controller PCB. A
press will automatically adjust the sensor output.
• The adjustment is over when all LEDs on the punch control-
ler PCB are ON: LED1001, LED1002, LED1003.
3)
Shift all bits of DIPSW1001 to OFF.
ON
1
2
3
4
5
6
7
8
+ direction
- direction
ON
1
2
3
4
5
6
7
8
+ direction
- direction
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
MX-FNX2/AR-PN1/MX-RBX1  ADJUSTMENTS  8 – 2
C. Registering the Number of Punch Hole
Perform the following to register the type of punch unit (number of
holes) used to the IC on the punch controller PCB for identification
by the finisher. Be sure to register the type whenever you have
replaced the punch controller PCB.
1)
Set bits 1 through 4 on the DIPSW1001 on the punch control-
ler PCB as follows:
2)
Press SW1002 on the punch controller PCB to select the
appropriate number of punch holes.
• Each press on SW1002 moves the selection through the fol-
lowing (repeatedly from top to bottom).
3)
Press SW1003 on the punch controller PCB twice. The
presses will store the selected number of punch holes on the
punch controller PCB.
• A single press on SW1003 will cause the LED indication to
flash; another press on SW1003 will cause the indication to
remain ON to indicate the end of registration.
4)
Shift all bits of DIPSW1001 to OFF.
D. After Replacing the EEP-ROM (IC1002)
1)
Turn off the host machine.
2)
Set bits 1 through 4 on the punch controller PCB as follows:
3)
Press SW1002 and SW1003 on the punch controller PCB at
the same time.
• The presses will initialize the EEP-ROM. At the end, all
LEDs (LED1001, LED1002, LED1003) will go ON.
4)
Adjust the sensor output, and store the number of punch
holes. Adjust the punch hole position adjustment (horizontal
registration) of necessary.
E. Setup by the diag simulation of the host 
machine
1)
Select "FINISHER ADJUSTMENT" in SIM 3-10.
2)
Select a setup item and change the setup value.
Adjustable setup range is as follows.
Number of punch holes
LED1001
LED1002
LED1003
2 holes (Punch Unit-J1)
ON
OFF
OFF
2/3 holes (Punch Unit-K1)
ON
ON
OFF
4 holes (Punch Unit-G1)
OFF
ON
OFF
4 holes (Punch Unit-H1)
OFF
OFF
ON
ON
1
2
3
4
ON
1
2
3
4
Adjustment content
Default 
value
Setup 
range
Change/Setup 
value 1
1
Saddle binding position 
adjustment
200
0 - 400
0.0707mm
2
Saddle folding position 
adjustment 
200
0 - 400
0.0525mm
3
Front alignment position 
adjustment
10
0 - 20
0.367mm
4
Rear alignment position 
adjustment
10
0 - 20
0.367mm
5
Staple front one-position 
binding position  adjustment
100
0 - 200
0.04374mm
6
Staple rear one-position 
binding position adjustment
100
0 - 200
0.04374mm
7
Staple 2-position binding 
center adjustment
100
0 - 200
0.04374mm
8
Staple 2-position binding 
pitch adjustment
50
0 - 100
0.04374mm
9
Punch center position 
adjustment (FR direction)
50
47 - 53
10
Punch hole position 
adjustment (paper feed 
direction)
50
0 - 100
0.105mm
OK
10-key
0
A:
A:200
B:200
C: 10
D:100
; SADDLE POSITION
; FOLDING POSITION
; FRONT ADJUSUT
; REAR ADJUSUT
SIMULATION NO.03-10
FINISHER ADJUSTMENT
200
[197-203]
OK
TEST
CLOSE
0
A:
A:197
B:200
C: 10
D:100
; SADDLE POSITION
; FOLDING POSITION
; FRONT ADJUSUT
; REAR ADJUSUT
SIMULATION NO.03-10
FINISHER ADJUSTMENT
197
[197-203]
OK
TEST
CLOSE
Display

Sharp MX-FNX2 (serv.man10) Service Manual ▷ Download

  • DOWNLOAD Sharp MX-FNX2 (serv.man10) Service Manual ↓ Size: 192.76 KB | Pages: 2 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp MX-FNX2 (serv.man10) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-FNX2 (serv.man10) Copying Equipment. Information contained in Sharp MX-FNX2 (serv.man10) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.