DOWNLOAD Sharp LL-T15S1 (serv.man11) Service Manual ↓ Size: 1.41 MB | Pages: 113 in PDF or view online for FREE

Dimensions (Units: mm)

LCD display

38 cm (diagonal)  TFT LCD module

Resolution (max.)

XGA 1024 x 768

Displayable colors (max.)

16.19 million colors (6bit + FRC2bit)

Dot pitch

0.297(H) x 0.297(V) mm

Brightness (max.)

200cd/m

2

Contrast ratio

300 : 1

Angle of visibility

Left-right 120°, Up-down 95°

Screen display size

Horizontal 304.1 mm x Vertical 228.1 mm

Video signal

Analog RGB (0.7Vp-p) [75

Ω

]

Sync signal

H-Sync (TTL level: +/-), V-Sync (TTL level: +/-)

Computer signal input terminal

15 pin mini D-sub connector

Plug & Play

VESA DDC1/DDC2B

Power management

VESA DPMS based

Microphone terminal

Mini stereo jack

Headphone terminal

Mini stereo jack

Audio input terminal

Mini stereo jack

Microphone output terminal

Mini stereo jack

Screen tilt

Upward 0-25°, Downward 0-3°

Temperature of operating environment

5 – 35°C

Power supply

AC100-240V 50/60Hz (use special AC adapter, tipe
NL-A53J of Sharp Corporation.)

Power consumption

31W max. (5W when in power-saving mode)

(use special AC adapter)

Dimensions (W x D x H)

368 mm X 170 mm x 355mm

Weight

Approx. 4.1 kg (excluding AC adapter)

130

368

45

313

355

200

170

RGB signal cable length: approx. 1.8 m

AC adapter

Approx. H 120 mm x D 60 mm x H 37 mm
Weight : Approx.350g

Approx.

1.8 m

All are compliant only with non-interlaced.

Frequencies for Power Macintosh are reference values.

If the monitor is receiving timing signals that are not compatible, [OUT OF TIMING] will appear. Follow your
computer's instruction manual to set the timing to be compatible with the monitor.

If the monitor is not receiving any signal (synch signal), [NO SIGNAL] will appear.

31.5kHz

60Hz

25.175MHz

640x480

37.9kHz

72Hz

31.5MHz

37.5kHz

75Hz

31.5MHz

VESA

35.1kHz

56Hz

36.0MHz

800x600

37.9kHz

60Hz

40.0MHz

48.1kHz

72Hz

50.0MHz

46.9kHz

75Hz

49.5MHz

48.4kHz

60Hz

65.0MHz

1024x768

56.5kHz

70Hz

75.0MHz

60.0kHz

75Hz

78.75MHz

US text

720x400

31.5kHz

70Hz

28.3MHz

Power Macintosh

640x480

35.0kHz

66.7Hz

30.5MHz

series

832x624

49.7kHz

74.6Hz

57.3MHz

1024x768

60.2kHz

75Hz

80.0MHz

Mini D-sub connector with 15 pins

Number

Function

1

Red video signal input

2

Green video signal input

3

Blue video signal input

4

N.C.

5

N.C.

6

For red video signal GND

7

For green video signal GND

8

For blue video signal GND

9

DDC + 5V

10

N.C.

11

GND

12

DDC data

13

For H-sync signal input

14

For V-sync signal input

15

DDC clock

The monitor is based on VESA DPMS (Display Power
Management Signaling).
To activate the monitor's Power Management function,
both the video card and the computer must conform to
the VESA DPMS standard.

This monitor supports the VESA DDC (Display Data
Channel) standard.
DDC is a signal standard for carrying out Plug & Play
functions on the monitor or PC. It transfers information
such as degree of resolution between the monitor and
PC. You can use this function if your PC is DDC compli-
ant and if it is set so that it can detect the Plug & Play
monitor.
There are many varieties of DDC due to the differences
between systems. This monitor works with DDC1 and
DDC2B.

DPMS mode

Screen

Power

H-sync V-sync

consumption

ON

Display on

31W

Yes

Yes

STANDBY

No

Yes

SUSPEND Display off

5W

Yes

No

OFF

No

No

 4. Remove the four screws and then remove the stand

from the monitor.

5. Attach the arm to the monitor with four screws.

6. Connect the AC adapter to the monitor's power

terminal.

Information
The stand is specially made for use with this
monitor. Once having removed the stand,
never attempt to attach it to another device.
Once having removed the screws, store
them together with the stand and if the stand
is ever re-attached be sure to use the
original screws.
Using different screws could lead to mal-
function

An arm based on the VESA standard can be attached to
the monitor. The arm must be purchased separately.

When choosing the arm to be installed please take note
of the following points.
-

The arm should be compatible with the VESA
standard, and there must be a gap of 75 mm x 75
mm between the screw holes on the section to be
attached.

The arm must not fall off or break off after being
attached to the monitor.

Do not bend the RGB signal cable or the AC adapter
cable nor place weight on them. Doing so could lead
to damage.

1. Turn off the power switch and remove the AC adapter

from the monitor's power terminal.

2. Remove the stand cover.

Pull the lower section of the stand cover upward.

3. Being careful not to damage the monitor, spread out

a soft cloth and lay the monitor on it display-side
down.

Information
The screws used to
attach the arm should
be M4 screws with a
length of 4 mm ~ 6 mm
protruding from the
surface to be attached.
Using different screws
could lead to malfunc-
tion or may lead to the
monitor falling off,
internal damaged,
personal injuly.

4 ~ 6 mm

Screw used to
attach arm

Arm

Part of monitor to
which arm is
attached

Stand cover