Sharp UP-V5500 (serv.man6) Service Manual ▷ View online
UP-V5500 S/M V1.1 – 2010-06-24 -*- Page
20 of 77
6. Hard-Disk Replacement
HDD Cover disassembly
3 screws of HDD cover in the bottom of the system like below picture.
DD - Disk disassembly
R
ve 4 screws like below picture, and disconnect HDD from the connector toward the direction of arrow.
DD - Disk replacement
emove 4 screws of A) in the both sides of HDD like below picture, disconnect bracket, replace HDD, and assembly
DD in the opposite order of disconnect.
Disassembly HDD cover by unbinding
H
emo
H
R
H
A) Remove screw
UP-V5500 S/M V1.1 – 2010-06-24 -*- Page
21 of 77
SYSTEM TURN POWER ON/OFF
After completing system installation, please turn on the system following next steps.
Press the power button located in the lower left side of system body.
el on the system front side is turned on.
ll be executed. These consecutive
tial
is firstly operated after
Please close all the application programs you are using.
ows, select "Shut down".
When user clicks "exit" button in the screen of "exit system", system will be closed.
1. Turning-on System
Turn on the power of the peripheral devices connected to the system.
The lamp of power display located in the lower right side of LCD pan
After checking memory capacity of the system, self diagnostic test wi
processes are to check that all the functions of the system are operated normally.
After checking memory capacity of the system, self diagnostic test wi
processes are to check that all the functions of the system are operated normally.
After self diagnostic test is complete, the initial screen of Windows will be displayed. Manufacturing ini
image (DriveClone Snapshot) will be automatically created in case that the system
manufacturing, and this process will take about 3 minutes. Rebooting will be executed once during image
creation and user input will not be necessary.
image (DriveClone Snapshot) will be automatically created in case that the system
manufacturing, and this process will take about 3 minutes. Rebooting will be executed once during image
creation and user input will not be necessary.
2. Turning Power-off System
After clicking "Start" button in the initial screen of Wind
ote!
Please press power button for 4 seconds in case that the system is shut down due to the sudden power supply
r system failure.
N
failure o
UP-V5500 S/M V1.1 – 2010-06-24 -*- Page
22 of 77
System Restoration (DriveClone)
This guide briefly shows the system restoration method using DriveClone that is the restoration solution
installed on UP-V5500. User can refer the DriveClone manual for the detailed information.
installed on UP-V5500. User can refer the DriveClone manual for the detailed information.
Restoration into manufacturing initial mode
1. Snapshot Restoration(Return to a system Snapshot)
1-3.
Pre-OS booting
This is the function for restoring system by booting as Pre-OS in case that Windows OS has been damaged.
If user presses F4 key on the keyboard while booting, system will be operated as Pre-OS provided from
DriveClon
DriveClon
Click "Return to a system Snapshot" of system after selecting "restore". The first system snapshot listed is
the newly created snapshot.
the newly created snapshot.
Click the date user wants to restore in the calendar on the left side, and click "next" after selecting the system
snapshot of the date user wants to restore on the right side.
snapshot of the date user wants to restore on the right side.
Click "next" in order to select "Entire Hard Drive" or "C:Drive Only" and start saving.
Click "OK" after reading warning message carefully.
(However, if there is no snapshot in the list, pre-OS would not be implemented by pressing F4 key.)
(However, if there is no snapshot in the list, pre-OS would not be implemented by pressing F4 key.)
UP-V5500 S/M V1.1 – 2010-06-24 -*- Page
23 of 77
1-2.
Windows
booting
If user
Execute DriveClone Pro 6.0 of wallpaper after system booting.
-OS status.
ry
Set up CD/DVD/USB Flash Memory is first priority after entering into CMOS setup by pressing "Del" key
when booting.
when booting.
Save changes by pressing F10 after setup and reboot the computer.
Main console will be executed while booting with the pre-OS of DriveClone.
Select "Restore – Restore Your Computer" in the main console.
Click "next" after selecting the restore point (file) in the CD/DVD/USB Flash Memory. If you can not find
the point to be restored in the "Select a Complete Backup Image", click "click here" in the lower of Details
and select the point to be restored.
the point to be restored in the "Select a Complete Backup Image", click "click here" in the lower of Details
and select the point to be restored.
Click "next" after selecting "Do not use Universal Restore".
Click "next" after selecting single partition or entire hard drive to be restored.
Click "next" in order to start restoration after checking source and target.
Click "OK" for automatic and complete restoration process.
Computer will restart for complete restoration, and then the system will be rebooted automatically.
** Create Bootable Rescue disk **
To create a USB bootable disk to recover from a system crash or hard drive failure, there should use FAT (16) formatted and
less than 2GB USB. And there should create booting image without any other data. CD/DVD is regardless of t
format,
can make a bootable rescue disk. However you will need a CD/DVD Rewritalbe Driver with USB interface.
Click "Return to a system Snapshot" after clicking "restore" in the main console.
The following processes are the same with snapshot restoration function operation under the pre
2. Restoration using CD/DVD/USB Flash Memo
he FAT
Click on the first or last page to see other UP-V5500 (serv.man6) service manuals if exist.