Sharp CD-C491H User Manual / Operation Manual ▷ View online
(Continued)
PTY.TI
SEARCH
SEARCH
Jog dial
EON
1
2
3
4
5
■
EON-TI
1
Tune in the desired RDS station, then the PS name will
be displayed.
be displayed.
2
Press the EON button when "EON" appears.
●
"PTY.TI" and "SELECT" will appear alternately for about
4 seconds.
4 seconds.
3
Whilst they are being displayed, select the TI (Traffic In-
formation) turning the jog dial.
formation) turning the jog dial.
●
The selected "TI" will flash.
4
Within 4 seconds, press the PTY.TI SEARCH button.
●
"TI" and "WAITING" will appear for 2 seconds each.
●
"TI" will appear, and the unit will enter the EON-TI stand-by
mode.
mode.
5
When a TA specifed starts on a other network station,
the unit will automatically switch to that station, and "TI"
will flash.
the unit will automatically switch to that station, and "TI"
will flash.
6
When the traffic announcement is over, the unit will au-
tomatically return to the original station you were tuned
to.
tomatically return to the original station you were tuned
to.
Note:
●
If the EON button is pressed when "EON" is not displayed,
"NO EON" will appear for 4 seconds to indicate that the
unit cannot enter the EON stand-by mode.
"NO EON" will appear for 4 seconds to indicate that the
unit cannot enter the EON stand-by mode.
Checking the stand-by mode setting:
When in the EON stand-by mode, press the EON button.
("TI"
("TI"
→
"WAITING")
To cancel the EON stand-by mode:
When in the EON stand-by mode, press the EON button.
Within 4 seconds, press it again. The EON stand-by mode
will be cancelled.
Within 4 seconds, press it again. The EON stand-by mode
will be cancelled.
●
"TI" will go out.
Note:
●
If neither "TP" nor "TA" appear, then even if "EON" ap-
pears the unit cannot enter the EON-TI stand-by mode.
In this condition, even if the EON button is pressed, "NO
TI" will flash for 4 seconds.
pears the unit cannot enter the EON-TI stand-by mode.
In this condition, even if the EON button is pressed, "NO
TI" will flash for 4 seconds.
Notes:
●
During the same programme as the specified PTY (or TA)
is being broadcast on the station you are receiving, the
unit will not switch to other network station.
is being broadcast on the station you are receiving, the
unit will not switch to other network station.
●
If there are more than two other network stations you want
to listen to, compare the strength of each station’s signal
and tune in the station with the strongest signal. (EON-AF)
However, if the frequency of other network station has
been stored in the preset channel memory, the unit will
switch to that preset channel.
to listen to, compare the strength of each station’s signal
and tune in the station with the strongest signal. (EON-AF)
However, if the frequency of other network station has
been stored in the preset channel memory, the unit will
switch to that preset channel.
●
If you want to cancel the reception of an ON (other net-
work) station which was tuned in by the EON system and
return to the original station you were receiving, press the
EON button.
work) station which was tuned in by the EON system and
return to the original station you were receiving, press the
EON button.
●
After the unit returns to the original station, the stand-by
mode will still be active. (The "TI" or "PTY" will remain lit.)
mode will still be active. (The "TI" or "PTY" will remain lit.)
●
The unit will not switch from the ON station to another
network station. The unit returns to the original station.
network station. The unit returns to the original station.
●
When the unit switches automatically to "other network"
station, if there is any problem with this station or the
station cannot be received properly, "NO READY" will ap-
pear and the unit will return to the original station.
station, if there is any problem with this station or the
station cannot be received properly, "NO READY" will ap-
pear and the unit will return to the original station.
CD-C491H(SUK) TINSE0229AWZZ
24
CASSETTE OPERATION
TAPE
(1 2)
ON/
STAND-BY
STAND-BY
ON/STAND-BY
TAPE 1
TAPE
(1 2)
4
3
ON/
STAND-BY
STAND-BY
ON/
STAND-BY
STAND-BY
TAPE 2
TAPE
(1 2)
REVERSE
MODE
MODE
TAPE
(1 2)
Reverse mode indicator
4
3
■
TAPE 1 playback
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TAPE (1
V
2) button to select TAPE 1.
3
Open the cassette door by pushing the area marked
"PUSH EJECT".
"PUSH EJECT".
4
Load a cassette into the TAPE 1 cassette compartment.
5
Press the
0
/
R
(
0
) button to start playback.
To stop playback:
Press the
■
(TAPE
■
) button.
■
TAPE 2 playback
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TAPE (1
V
2) button to select TAPE 2.
3
Open the cassette door by pushing the area marked
"PUSH EJECT".
"PUSH EJECT".
4
Load a cassette into the TAPE 2 cassette compartment.
5
Press the REVERSE MODE button.
... To listen to one side of the tape.
... To listen to both sides of the tape.
... For endless repeat play of both sides of the tape.
... To listen to both sides of the tape.
... For endless repeat play of both sides of the tape.
( )
( )
( )
( )
6
Press the
0
/
R
(
0
) button to listen to side A (1), or
the
1
button for side B (2).
●
To play both sides of the tape ( ), start from side A
(1). When the tape starts playback from side B (2), side
A (1) will not be played after side B (2) finishes.
(1). When the tape starts playback from side B (2), side
A (1) will not be played after side B (2) finishes.
To stop playback:
Press the
■
(TAPE
■
) button.
Fast forward/rewind:
➀
Press the
■
(TAPE
■
) button, then the TAPE (1
V
2) button
to select TAPE 2.
➁
To advance the tape, press the
2
button. To rewind it,
press the
3
button.
Caution:
●
To remove the cassette tape, press the
■
(TAPE
■
) but-
ton, and then open the cassette compartment.
●
Before changing from one tape operation to another, press
the
the
■
(TAPE
■
) button.
●
If a power failure occurs during tape operation, the tape
head will remain engaged with the tape and the cassette
door will not open. In this case, wait until the power is
restored.
head will remain engaged with the tape and the cassette
door will not open. In this case, wait until the power is
restored.
CD-C491H(SUK) TINSE0229AWZZ
25
RECORDING
●
When recording important selections, be sure to make a
preliminary test to ensure that the desired material is being
properly recorded.
preliminary test to ensure that the desired material is being
properly recorded.
●
The ALC (Automatic Record Level Control) circuit auto-
matically controls the level of the input signal used for
recording.
matically controls the level of the input signal used for
recording.
ON/
STAND-BY
STAND-BY
TAPE
(1 2)
REVERSE
MODE
MODE
CD
NORMAL
TAPE 2
1
CD
A
B
2
3
4
5
1
TAPE
2
3
4
5
●
The volume and sound quality may be adjusted without
affecting the signal being recorded at the same time.
(Variable Sound Monitor)
affecting the signal being recorded at the same time.
(Variable Sound Monitor)
●
Metal tape should not be used for recording or dubbing.
■
Recording from the built-in CD player
(CD Synchronised Recording System)
(CD Synchronised Recording System)
(Main unit operation)
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TAPE (1
V
2) button to select TAPE 2.
3
Load a cassette into the TAPE 2 cassette compartment.
●
Wind past the tape leader, on which a recording can not
be performed.
be performed.
4
Press the REVERSE MODE button.
... To record on only one side.
... To record on both sides.
... To record on both sides.
5
Press the CD button and load the desired disc.
●
Use the APMS function to store the tracks you want to
record in memory. (See page 16.)
record in memory. (See page 16.)
6
Press the NORMAL EDIT button.
●
At this point, the HIGH EDIT button will not work.
●
CD playback will start approximately 2 seconds after the
side A (1) tape starts.
side A (1) tape starts.
Note:
●
Do not open the disc tray whilst recording the CD.
To stop recording:
Press the
■
button.
●
The CD and tape will stop.
Auto restart function:
●
When recording continuously on both sides of the
tape:
tape:
Even if the last track of side A (1) is not finished recording,
side B (2) will automatically start recording from the beginning
of that track.
The recording will be made without cutting the beginning of
the track on side B (2).
side B (2) will automatically start recording from the beginning
of that track.
The recording will be made without cutting the beginning of
the track on side B (2).
CD-C491H(SUK) TINSE0229AWZZ
26
(Continued)
BEAT
CANCEL
CANCEL
REVERSE
MODE
MODE
TAPE
(1 2)
2
NORMAL
HIGH
TAPE
(1 2)
REVERSE
MODE
MODE
ON/
STAND-BY
STAND-BY
3
■
Recording from the built-in radio
1
Press the TAPE (1
V
2) button to select TAPE 2.
2
Load a cassette into the TAPE 2 cassette compartment.
●
Load the tape with the side to be recorded facing you.
●
Wind past the tape leader, on which a recording can not
be performed.
be performed.
3
Press the REVERSE MODE button.
... To record on only one side.
... To record on both sides.
... To record on both sides.
4
Tune in to the desired station. (See pages 17-18.)
5
Press the REC PAUSE
●
6
(
●
6
) button.
●
"REC" will flash.
6
Press the
0
/
R
button to record side A (1), or the
1
button to record side B (2).
Beat cancel button:
If a whistling noise is heard when recording an MW or LW station,
you can choose the level which gives the best reception by pressing
the BEAT CANCEL button on the main unit.
If a whistling noise is heard when recording an MW or LW station,
you can choose the level which gives the best reception by pressing
the BEAT CANCEL button on the main unit.
To stop recording:
Press the
■
button.
■
Dubbing from tape to tape
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TAPE (1
V
2) button to select TAPE 1.
3
Load a prerecorded cassette into the TAPE 1 cassette
compartment. Insert a blank tape into the TAPE 2 cas-
sette compartment.
compartment. Insert a blank tape into the TAPE 2 cas-
sette compartment.
●
It is recommended that the recording tape be the same
length as the master tape.
length as the master tape.
4
Press the NORMAL EDIT button to enter the normal
speed dubbing mode. Press the HIGH EDIT button to
enter the high speed dubbing mode.
speed dubbing mode. Press the HIGH EDIT button to
enter the high speed dubbing mode.
●
The reverse mode will be set to .
To stop dubbing:
Press the
■
button.
●
TAPE 1 and TAPE 2 will simultaneously stop.
■
Erasing recorded tapes
●
Make sure that TAPE 1 is not in use.
1
Load the tape to be erased into the TAPE 2 cassette
compartment.
compartment.
2
Press the TAPE (1
V
2) button to select TAPE 2.
3
Set the REVERSE MODE button to to erase only one
side and to to erase both sides.
side and to to erase both sides.
4
Press the REC PAUSE
●
6
(
●
6
) button.
●
"REC" will flash.
5
Press the
0
/
R
button to erase side A (1), or the
1
button to erase side B (2).
●
To erase on both sides, begin on side A (1). [If erasing
is started from side B (2), the tape will not switch over to
side A (1).]
is started from side B (2), the tape will not switch over to
side A (1).]
CD-C491H(SUK) TINSE0229AWZZ
27
Click on the first or last page to see other CD-C491H service manuals if exist.