Panasonic KX-TGK310RUB / KX-TGK320RUB / KX-TGKA31RUB Service Manual ▷ View online
57
KX-TGK310SP/KX-TGK310JT/KX-TGK320JT/KX-TGK310FR/KX-TGK310RU/KX-TGK320RU/KX-TGK310NE//KX-TGK310GR/KX-TGKA31EX/KX-TGKA31RU
11.6.1.2. Handset
First, operate the PC setting according to The Setting Method of JIG (P.50).
Then download the appropriate data according to the following procedures.
Then download the appropriate data according to the following procedures.
Note:
(*2) WW: country code, XXX_YYY: revision number
“XXX_YYY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting
Method of JIG (P.50).
“XXX_YYY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting
Method of JIG (P.50).
Items
How to download/Required adjustment
FLASH(IC4)
Adjusted parameter data is
stored in memory.
(country version batch file,
default batch file,ect)
stored in memory.
(country version batch file,
default batch file,ect)
1) Please be sure to execute the following steps if you have replaced the FLASH
IC(IC4).
IC(IC4).
1. Update BBIC. Refer How to update the BBIC.
2. Detach the JIG cable, then disconnect the battery.
3. Insert battery.
4. Connect the JIG cable again, and execute the command "getchk", then con-
2. Detach the JIG cable, then disconnect the battery.
3. Insert battery.
4. Connect the JIG cable again, and execute the command "getchk", then con-
firm the checksum value is correct.
• If the downloading failes, start again from step 1.
5. Check DECT ID written on Plastic bag of FLASH (IC4).
6. Execute the command "idw xx xx xx xx xx". xx xx xx xx xx: use DECT ID in
6. Execute the command "idw xx xx xx xx xx". xx xx xx xx xx: use DECT ID in
Step 5.
7. Execute the command "epw 00 01 01 AA".
8. Default bath file: Execute the command "default.bat"
9. Common batch file: Execute the command
8. Default bath file: Execute the command "default.bat"
9. Common batch file: Execute the command
"TGKA30_E_DEF_RevXXX_YYY.bat" (for SP, JT, FR, NE, GR) or
"TGKA30_RU_DEF_RevXXX_YYY.bat" (for RU)(*2).
"TGKA30_RU_DEF_RevXXX_YYY.bat" (for RU)(*2).
10. Country version batch file: Execute the command
"TGKA30_E_WW_RevXXX_YYY.bat" (for SP, JT, FR, NE, GR) or
"TGKA30_RU_WW_RevXXX_YYY.bat" (for RU)(*2).
"TGKA30_RU_WW_RevXXX_YYY.bat" (for RU)(*2).
11. Confirm DECT ID written in the label pated plastic bag of FLASH rom.
12. Write ID(PFPI): Write DECT ID.
• Execute the command "IDWRITE". Refer to 11.2.3 Commands (P.51)
2) Clock adjustment.
3) 2.35 V setting and battery low detection.
3) 2.35 V setting and battery low detection.
Battery Low Confirmation
-
1) Apply 2.40 V between BATT+ and BATT-.
2) Confirm that there is no flashing of Battery lcon.
3) Apply 2.25 V ± 0.08 V between BATT+ and BATT-.
4) Confirm that there is flashing of Battery lcon.
If need to adjust Battery low detection, please proceed as below.
5) Apply 2.25V between BATT+ and BATT-
Execute the command
sendchar PAD
sendchar LED 0
sendchar CRX 0 1
sendchar AD1
It assumes that the return value is XX*.
a) 6c XX 71: No need to adjust
b) XX: 6A ~ 6B: Need to adjust
Execute the command
wreeprom 00 09 01 XX
wreeprom 00 0A 01 ZZ
ZZ = XX-1D (hex)
Note:
* : If XX is “00” to “69” or “75” to “FF” it may not be able to adjust properly.
Please check power circuit.
2) Confirm that there is no flashing of Battery lcon.
3) Apply 2.25 V ± 0.08 V between BATT+ and BATT-.
4) Confirm that there is flashing of Battery lcon.
If need to adjust Battery low detection, please proceed as below.
5) Apply 2.25V between BATT+ and BATT-
Execute the command
sendchar PAD
sendchar LED 0
sendchar CRX 0 1
sendchar AD1
It assumes that the return value is XX*.
a) 6c XX 71: No need to adjust
b) XX: 6A ~ 6B: Need to adjust
Execute the command
wreeprom 00 09 01 XX
wreeprom 00 0A 01 ZZ
ZZ = XX-1D (hex)
Note:
* : If XX is “00” to “69” or “75” to “FF” it may not be able to adjust properly.
Please check power circuit.
Clock Adjustment (X1)
CLK
1) Apply 2.6 V between BATT+ and BATT- with DC power.
2) Input Command “sendchar sfr“, then you can confirm the current value.
3) Check X’tal Frequency. (10.368 MHz ± 100 Hz).
4) If the frequency is not 10.368 MHz ± 100 Hz, adjust the frequency of CLK
execute in the command “sendchar sfr xx xx (where xx is the value)“ so that the
reading of the frequency counter is 10.368000 MHz ± 5 Hz.
2) Input Command “sendchar sfr“, then you can confirm the current value.
3) Check X’tal Frequency. (10.368 MHz ± 100 Hz).
4) If the frequency is not 10.368 MHz ± 100 Hz, adjust the frequency of CLK
execute in the command “sendchar sfr xx xx (where xx is the value)“ so that the
reading of the frequency counter is 10.368000 MHz ± 5 Hz.
58
KX-TGK310SP/KX-TGK310JT/KX-TGK320JT/KX-TGK310FR/KX-TGK310RU/KX-TGK320RU/KX-TGK310NE//KX-TGK310GR/KX-TGKA31EX/KX-TGKA31RU
11.6.1.2.1. How to update the BBIC.
• Execute COM communicator.exe
1. Initialize COM port.(Only once at first.)
Select “Setting”
“Serial Port” “Initial Setting “OK”.
2.Select serial port COM number.
Select “Setting”
“Serial Port” “Initial Setting “OK”.
Fill up the “COM Option”
“OK”.
Note:
Once download is successful for a PC, this step is unnecessary next time to the PC.
Setting
Serial Port
Initial Setting
OK
Cancel
(1)
(2)
(3)
Setting
Serial Port
Initial Setting
OK
Cancel
59
KX-TGK310SP/KX-TGK310JT/KX-TGK320JT/KX-TGK310FR/KX-TGK310RU/KX-TGK320RU/KX-TGK310NE//KX-TGK310GR/KX-TGKA31EX/KX-TGKA31RU
• Execute COM communicator.exe again <<Write program>>
1. Select “ProgramLoader”.
2. Select "Setting"/"Config".
Fill up the “Config Settings”.
Note:
(2) Select Baud Rate as 57600. If write error happens, select slower Baud Rate (example: 19200).
3. Select download file.
(1)
(2)
(3)
(1)
(2)
60
KX-TGK310SP/KX-TGK310JT/KX-TGK320JT/KX-TGK310FR/KX-TGK310RU/KX-TGK320RU/KX-TGK310NE//KX-TGK310GR/KX-TGKA31EX/KX-TGKA31RU
4. Start download.
(1). Connect Unit and 3wire jig.
(2). Confirm "Turn on power to target and press download." display.
(3). Power off the unit, then power on.
(4). Press "Download" button again.
(2). Confirm "Turn on power to target and press download." display.
(3). Power off the unit, then power on.
(4). Press "Download" button again.
5. Finish download.
Completed dialog means "Download finished successfully!." It takes more than 20 minutes to download
( It depends on baud rate). If error message is displayed, proceed from step 3 again.
6. Continuous download.
Write next unit's software with proceeding from step 3 to Step 5.
(2)
(4)
Click on the first or last page to see other KX-TGK310RUB / KX-TGK320RUB / KX-TGKA31RUB service manuals if exist.