Panasonic PT-RZ770 / PT-RW730 / PT-RZ660 / PT-RW620 (serv.man2) Service Manual ▷ View online
INF-13
SECTION 1 SERVICE INFORMATION
< RZ770/RW730/RZ660/RW620 >
(1) --- Projector type (Model No.)
(2) --- Projector serial number
(3) --- Main microprocessor firmware version
(4) --- Sub microprocessor firmware version
(5) --- DIGITAL LINK firmware version
(6) --- Formatter firmware version
(7) --- FPGA firmware version (FPGA1/FPGA2)
(8) --- LD driver firmware version
(9) --- LD sub microprocessor firmware version
(10) --- Status of EMULATE setting
(11) --- Intake air temperature (Celsius/Fahrenheit)
(12) --- DMD temperature (Celsius/Fahrenheit)
(13) --- Exhaust air temperature (Celsius/Fahrenheit)
(14) --- LD1 temperature (Celsius)
(15) --- LD2 temperature (Celsius)
(16) --- LD1 check (1: normal / 0:stop)
(17) --- LD2 check (1: normal / 0:stop)
(18) --- Fans control check (1: normal / 0: abnormal)
(19) --- Luminance sensor check (Detected value:Red/Green/Blue/Yellow)
(20) --- Atmospheric pressure sensor check (hPa/Celsius)
(21) --- Angle sensor check (Horizontal angle/Vertical angle)
f
The following information is available for Asian model only.
(22) --- Communication status of the WL-P.C.Board
- YES : Communication good
- NO : Communication error (faulty or disconnected)
(23) --- Firmware version of IC on the WL-P.C.Board
(24) --- Usage environment information
- Applicable country Information/Nonapplicable country Information
(25) --- Functional restriction setting status
- YES : Function restriction has been canceled
- NO : Function restriction has been enabled
(26) --- Function restriction countdown
- Count of communication error/Count of environmental error
- Count is decreased when an error is detected, and become restricted with counter " 0 ". (Maximum 30)
LD2 LD3 LD4
LD1
LD2 LD3 LD4
LD1
RADIA
TOR3
PW1
PW2
POWER
LD DRIVER
EXHAUST3
DMD
EXHAUST1
EXHAUST2
RADIA
TOR2
RADIA
TOR1
PUMP1
PUMP2
* RZ660/RW620 are not mounted with PW1/PW2 fans, but display will be "1".
INF-14
SECTION 1 SERVICE INFORMATION
< RZ770/RW730/RZ660/RW620 >
4. AUTO INDEX CALIBRATION
• When replaced the phosphor wheel or color wheel, perform automatic adjustment of each wheel rotational phase.
* Please refer to SECTION 3 (Adjustments) for the procedure.
5. PW1 INDEX
6. PW2 INDEX
6. PW2 INDEX
•
Make the rotation phase adjustment of the wheels individually.
7. CW INDEX
8. POWER OFF MESSAGE
• Operation setting of shutter at standby operation.
- SHUTTER KEEP: When pushing the standby key while the shutter mode is on, the projector keeps the shutter mode
on and sets into standby mode.
- SHUTTER OPEN: When pushing the standby key while the shutter mode is on, the projector opens the shutter and
displays the "Power OFF confirmation message". (Default setting)
9. ERROR OSD
• Enables to display the error information of the LIGHT indicators on the screen.
(It is useful when using the projector with rear projection mode)
- ON : "LD1\LD2 ERROR" is displayed on the screen if the lighting error occurs.
(It will disappear when any of the control buttons is pressed.)
- OFF : No message is displayed on the screen if the lighting error occurs. (Default setting)
10. MODEL
• This setting is necessary when the A-P.C. Board is replaced with new one.
* If you can copy EEPROM data from old A-P.C. Board, this setting is unnecessary.
* This model setting is effective after power restart.
11. LIGHT SELECT
• Select the LD units to turn on. Press the [ENTER] key to switch.
- ALL : All LD blocks will light. (Default)
- LIGHT1 : LD1 block will light.
- LIGHT2 : LD2 block will light.
• To return ALL When turn off the power.
12. MUTE TIME OFFSET
• Set the extension of black mute time.
It hides the input switching noise.
- DISABLE : Does not extend the mute time. (Default)
- 0.5s : Mute time will be extended 0.5 seconds.
- 5.0s : Mute time will be extended 5.0 seconds.
13. EDID 48HZ SETTING
• Add a [48Hz] in vertical scan frequency to user setting of EDID.
(When resolution is [1920x1080p] or [1920x1200p].)
- OFF : 48Hz vertical scanning frequency is not added. (Default)
- ON : Vertical scanning frequency 48Hz can be selected.
(Do not change the setting, usually.)
～
(0.5 second step)
INF-15
SECTION 1 SERVICE INFORMATION
< RZ770/RW730/RZ660/RW620 >
4. 3. 2. Additional function of each menu
1. [PICTURE] menu
• [AI WINDOW] is added to the setting of the sub menu [DYNAMIC CONTRAST].
- Sets up the APL detective area. (AUTO/MANUAL, further settings are available in MANUAL mode)
2. [POSITION] menu
• [DVI/HDMI EQUALIZER] is added to a sub menu.
- When noise contamination to DVI/HDMI input caused by long cable or external device, set this item so that the noise
decreases. (AUTO/LOW/MID/HIGH)
INF-16
SECTION 1 SERVICE INFORMATION
< RZ770/RW730/RZ660/RW620 >
3. [PROJECTOR SETUP] menu
(1) The following two items are added to the sub-menu.
1) [COOLING CONDITION]
- Fan control can be set manually. (Usually set to [AUTO].)
2) [HIGH ALTITUDE MODE]
- Altitude can be set manually. (Usually set to [AUTO].)
(2) In the [BRIGHTNESS CONTROL STATUS] sub menu, [DETAILED INFORMATION] is displayed by pressing the [ENTER]
key.
- The detailed information of brightness control can be checked.
Click on the first or last page to see other PT-RZ770 / PT-RW730 / PT-RZ660 / PT-RW620 (serv.man2) service manuals if exist.