DOWNLOAD Panasonic DP-2310 / DP-3010 / DP-2330 / DP-3030 (serv.man2) Service Manual ↓ Size: 47.79 MB | Pages: 127 in PDF or view online for FREE

Model
DP-2310 DP-3010 DP-2330 DP-3030 (serv.man2)
Pages
127
Size
47.79 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / DIGITAL IMAGING SYSTEMS
File
dp-2310-dp-3010-dp-2330-dp-3030-sm2.pdf
Date
PREV: Panasonic DP-2310 / DP-3010 / DP-2330 / DP-3030 Service Manual / Other

Panasonic DP-2310 / DP-3010 / DP-2330 / DP-3030 (serv.man2) Service Manual ▷ View online

85
DP-2330/3030
MAR 2005
Ver. 2.1
DP-2310/3010
Part No.
Figure
Remark
Ref. No.
Screw
DZPA000086
S6
Screw
FFPFA0152
P7
Screw
XTN3+8G
P5
Snap Ring
DZJM000171
S9
Silver Screw
XTW3+10LFN
V4
Screw
DZPA000087
T2
Screw
XTB3+12J
P2
XTB3+12JFJ
Tumb Screw
DZPA000064
M2
Screw
B3x6TTS-RP
P1
XTB3+6FFJ-RP
Red Screw
XTB3+12F
S8
XTB4+10F
N3
XYN3+F5FY
T4
XTN3+6FR-C
T5
XTB3+12FFJ
XTB4+10FFJ
XYN3+F5FJ
XTN3+6FFJR
Screw
Screw
Screw
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Screw (For DP-2310/3010 only)
Red Screw (For DP-2310/3010 only)
86
DP-2330/3030
MAR 2005
Ver.2.1
DP-2310/3010
3 Maintenance, Adjustments and Check Points
3.1.
Preventive Maintenance
Preventive maintenance is performed at specific intervals and consists of machine
cleaning and parts replacement.
It is essential to perform these service activities properly and at the specified intervals
for customer satisfaction.
The purpose of this service is to maintain machine performance and image quality.
- You should prepare the necessary PM kits, replacement parts, and tools for
cleaning beforehand.
- After completing the preventive maintenance service, you should discard the
used parts and packaging, in accordance with local regulations and clean
the surrounding area.
- Before servicing the equipment disconnect the power cord from the wall outlet.
- Before using solvents such as IPA (Isopropyl alcohol), put on rubber gloves
and eye protection.
1
Timing
- Perform the preventive maintenance in accordance with the Preventive
Maintenance Check List (refer to 3.4) in the service manual.
2
Cleaning of Rollers
- Rollers should be cleaned with water and cloth.
- Use of IPA (Isopropyl alcohol) should be used sparingly.
3
Disassembly and Adjustment Precautions
Turn the Power Switch on the Left Side and the Main Power Switch on 
the Back of the machine to the OFF position, and then unplug the AC Power 
Cord from the wall outlet before disassembling the machine.
CAUTION!
- After taking the unit apart, do not attempt to operate the machine.
- When operating the machine with covers removed, be careful to avoid clothing
being caught by moving components.
- While electricity is applied, the connectors of any PC Board must not be 
connected or disconnected.
- Use of a vacuum cleaner for the cleaning of the TDC sensor could cause
electrostatic damage, therefore, use a blower brush or cotton swab for the
cleaning of these parts.  Before vacuuming the developer unit remove the TDC
sensor.
- When handling the drum, the precautions listed in section 3.3. 
 
 
should be followed.
- Make sure to use the correct screw sizes.
- Use toothed lock washers for the installation of ground wires to ensure electrical
continuity.
- To re-assemble, reverse the sequence of disassembly, unless otherwise specified.
- Blown fuses should only be replaced with fuses of the same specified rating.
87
DP-2330/3030
MAR 2005
Ver. 2.1
DP-2310/3010
4
Laser Handling Precautions 
The optical laser system employed by this photocopier is completely sealed by
a protective housing and an external cover. Therefore, the laser beam will not
stray or leak during photocopying operation. 
However, when servicing the photocopier, take the following precautions:
1. Do not insert any screwdrivers or other tools that have high reflective
properties into the laser's path.
.
2. Before servicing the machine, remove watches, rings, or other metallic
objects that you may be wearing. (This is to avoid the danger of the laser
striking the eye by reflecting off the metallic objects being worn.)
Since the laser beam cannot be seen with the naked eye, for maximum
safety, please follow the above precautions.
88
DP-2330/3030
MAR 2005
Ver.2.1
DP-2310/3010
3.2.
Required Tools
3.2.1.
Preventive Maintenance Method
No.
Tools
No.
Tools
1
Soft Cloth
7
Pliers
2
Isopropyl Alcohol
8
Cotton Swab
3
Phillips Screwdriver (#2)
9
Brush
4
Stubby Phillips Screwdriver (#2)
10
KS-660 - Conductive Grease
(Available from Shin-Etsu Silicones of America, Inc.  
URL: 
http://www.shinetsusilicones.com
) 
5
Slotted Screwdriver (3/32 in)
11
Molykote EM-50L Grease 
(Available from Dow Corning, 
URL: 
http://www.dowcorning.com
)
6
Tweezer
No.
Part Description
Important 
Action
Comments
1
Memory Data
Check
1. Print the RAM DATA for reference and as a pre-caution.
2. After completing the task(s), print and compare the RAM 
DATA with the previously printed one.
2
Auto Document 
Feeder (ADF)
Check & 
Clean
1. Clean the Rollers and Separation Rubber with Isopropyl 
Alcohol when required.
3
Scanner Unit
Check & 
Clean
1. Clean the Scanning Glass or White Seal Guide with 
Isopropyl Alcohol when required.
4
Transmitter Unit
Check & 
Clean
1. Remove any foreign obstacles.
2. Clean the Rollers with Isopropyl Alcohol when required.
5
Mirrors
Check & 
Clean
1. Do not touch the surface of the Mirrors with your hands.
Clean any dirt or fingerprints with a soft cloth, saturated with 
Isopropyl Alcohol.
6
Inspection Items
Check
1. Check the Harnesses.
2. Check the Connectors.
3. Check the Screws. If required, replace consumable parts.
7
Gears, Rollers Shafts Check & 
Grease
1. Check and grease the required Gears and Shafts.
8
Timing Belts
Check & 
Clean
1. Check the belts for looseness or abrasion.
2. Adjust the Idle Pulley.
Page of 127
Display

Click on the first or last page to see other DP-2310 / DP-3010 / DP-2330 / DP-3030 (serv.man2) service manuals if exist.

RANDOM: