DOWNLOAD Panasonic TX-P65VT60Y / TX-PR65VT60 Service Manual ↓ Size: 2.79 MB | Pages: 46 in PDF or view online for FREE

9

1. NAND Flash (IC8900) for spare parts has the seed of KEY for each DTCP-IP for DLNA, WMDRM for Netflix and Widevine for 

CinemaNow.

2. The final KEY data will be generated by Main IC (IC8000) when SELF CHECK was done and are stored in both Main IC 

(IC8000) and NAND Flash (IC8900).

When Main IC (IC8000) is replaced, NAND Flash (IC8900) should be also replaced with new one the same time.
When NAND Flash (IC8900) is replaced, Main IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for 
more than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK.

Digital TV programmes can be recorded in USB HDD.
A One-to-One key generated in A-board by SELF CHECK binds TV and USB-HDD for communication.
That key is only one key for them. If the key is difference, TV can not access USB-HDD.

Model No.

Keys

One-to-One

(For USB Rec.)

CI Plus

DTCP-IP

WIDEVINE

Netflix

TX-P65VT60Y

Yes

Yes

Yes

Yes

Yes

TX-PR65VT60

Yes

Yes

Yes

Yes

Yes

10

The Service port (M3 mini Jack) on the following TVs can use as the RS232C terminal which is a standard computer SERIAL 
interface.
 *This operation system should be used by the certified professional dealer.

• The TV can be controlled by a personal computer when connected through an RS232C/ M3 mini jack conversion cable (not 

supplied).

• The computer will require software which allows sending and receiving of control data through its SERIAL port.

Please see required parameters and commands below.

The transmission of control data from the PC starts with a STX signal, followed by the command, the parameters, and lastly an 
EXT signal in that order. If there are no parameters, then the parameter signal does not need to be sent.
*Please see other side regarding Commands and Parameters.

• With standby mode, this TV responds to "PON" and "QPW" commands only.
• Wait for the response of the first command to come from this unit before sending the next command.
• If multiple commands are transmitted, be sure to keep intervals of 250 m sec.

Send the command again when the call back command is unusual.

• If an incorrect command is sent by mistake, this TV will send an "ER401" or "ER402" command back to the computer.
• This TV does not respond for 15 seconds when "PON" or "POF" commands are transmitted.
• Send "EXT" commands before sending "IMS:**" commands.
• MUTE commands ("AMT: 0" and "AMT: 1") and "AVL: ***" command are invalid in case of HDMI (CEC) cooperation.

However AMT, AUU, AUD commands is effective. (MUTE rotation (toggle), VOLUME UP and VOLUME DOWN controls are 
possible.)

Signal level 

RS-232C compliant

Synchronization method 

Asynchronous

Baud rate 

9600 bps

Parity None

Character length 

8 bits

Stop bit 

1 bit

Flow control 

-

11

Control 

Command

Inquiry 

Command

Call back 

Command

Parameter

note

STANDARD 

CONTROL

POWER ON

PON

QPW

QPW : *

"0"(OFF)/ "1"(ON)

POWER OFF

POF

VOL

(level)

AVL: ***

QAV

QAV : ***

"000" - "100"

(up)

AUU

(down)

AUD

MUTE

AMT (Toggle)

QAM

QAM : *

"0"(NO MUTED)

/ "1"(MUTED)

AMT: *

ASPECT

DAM: ****

QAS

QAS : **** "FULL" / "JUST" / 

"NORM"(4:3) / 
"ZOOM" / "HFIL" / 
"SJST" / "SZOM"
"SELF" (Auto)
"14:9" 

(480i/480p)
Option : Full 

→ Just → 4:3 → Zoom

(1080i/720p/1080p)
Option : Full 

→ Just → 4:3 → Zoom → H-Fill  → 

Sidecut Just 

→ Sidecut Zoom

DAM 

(Toggle)

INPUT 

SELECT

CH UP

CHU

--

--

--

CH DOWN

CHD

--

--

--

TV

IMS : TV

QMI

QMI : **

"TV"

Analogue TV

IMS : TVA

"TVA"

DVB-T

IMS : TVD

"TVD"

DVB-S/Other Sat

IMS : BS1

"BS1"

Freesat

IMS : BS2

"BS2"

DVB-C

IMS : CAB

"CAB"

Video 1

IMS : V1

"V1"

Video 2

IMS : V2

"V2"

Component 1

IMS : C1

"C1"

HDMI 1

IMS : H1

"H1"

HDMI 2

IMS : H2

"H2"

HDMI 3

IMS : H3

"H3"

SD/USB

IMS : SDU

"SDU"

VIEWING 

MODE

Dynamic

VPC : VVT

QPC

QPC : ***

"VVT"

Normal

VPC : STD

"STD"

THX Cinema / 
THX 3D Cinema

VPC : THX

"THX"

THX : Except  PHOTO(JPEG), MUSIC, VIErA 
Connect & MEDIA SERVER(DLNA/RUI)

THX Bright Room

VPC : THB

"THB"

True Cinema

VPC : CNM

"CNM"

Cinema

VPC : THR

"THR"

Custom

VPC : CST

"CST"

EBU default

VPC : EBU

"EBU"

Only for ZT60 series

Professional 1 (isf day)

VPC : PR1

"PR1"

When Advance(isfccc) menu is On.

Professional 2 (isf night)

VPC : PR2

"PR2"

12

Control 

Command

Inquiry 

Command

Call back 

Command

Parameter

note

LAST VIEW

LCH

Information

INF

--

QIF

QIF : *****

480i

480p

576i

576p
720p

1080i

1080p

DIRECT CH 

INPUT

0

ICH : 0

-

-

-

1

ICH : 1

-

-

-

2

ICH : 2

-

-

-

3

ICH : 3

-

-

-

4

ICH : 4

-

-

-

5

ICH : 5

-

-

-

6

ICH : 6

-

-

-

7

ICH : 7

-

-

-

8

ICH : 8

-

-

-

9

ICH : 9

-

-

-

MENU 

FUNCTION

MENU

MEN

-

-

-

SELECT

SEL

-

-

-

RETURN

RTN

-

-

-

EXIT

EXT

-

-

-

ARROW LEFT

ARL

-

-

-

ARROW RIGHT

ARR

-

-

-

ARROW UP

ARU

-

-

-

ARROW DOWN

ARD

-

-

-

OPTION

OSM

-

-

-

RED

RED

-

-

-

GREEN

GRN

-

-

-

YELLOW

YEL

-

-

-

BLUE

BLU

-

-

-

APPS

APS

-

-

-

HOME

HOM

-

-

-

3D

O3D

-

-

-