Panasonic TX-P65VT60Y / TX-PR65VT60 Service Manual ▷ View online
25
9 Disassembly and Assembly Instructions
9.1.
Disassembly Flow Chart for the Unit
This is a disassembly chart.
When assembling, perform this chart conversely.
When assembling, perform this chart conversely.
26
9.2.
Disassembly Procedure for the Unit
9.2.1.
Remove the Pedestal stand
1. Remove the Plasma panel section from the servicing
stand and lay on a flat surface such as a table (covered
by a soft cloth) with the Plasma panel surface facing
downward.
by a soft cloth) with the Plasma panel surface facing
downward.
2. Remove the screws (
×4 )
3. Slide the Pedestal stand to the downside and remove the
Pedestal stand.
9.2.2.
Remove the Bottom cover
1. Remove the screws (
×4
) and remove the Bottom
cover.
9.2.3.
Remove the AC cord clamper B
1. Remove the screws (
×2
) and remove the AC cord
clamper B.
9.2.4.
Remove the Wi-Fi module
1. Remove the screw (
×1
) and remove the Wi-Fi
module.
9.2.5.
Remove the Bluetooth module
1. Remove the screw (
×1
) and remove the Dongle
cover.
2. Remove the Pin guides (
×2
) and disconnect the BT
connector.
3. Remove the Bluetooth module.
9.2.6.
Remove the Camera bracket cover
1. Remove the screws (
×2
) and remove the Camera
bracket cover.
27
9.2.7.
Remove the Rear cover
1. Remove the screws (
×33 ,
×2 ).
2. Remove the M8 caps (
×4 ).
3. Remove the Rear cover.
9.2.8.
Remove the AC inlet
Caution:
To remove AC inlet wait 1 minute after power was off for
discharge from electrolysis capacitors.
discharge from electrolysis capacitors.
1. Disconnect the connector (P9).
2. Remove the screws (
2. Remove the screws (
×1 ,
×1
) and remove the AC
inlet.
9.2.9.
Remove the P(MAIN)-Board
Caution:
To remove P.C.B. wait 1 minute after power was off for
discharge from electrolysis capacitors.
discharge from electrolysis capacitors.
1. Unlock the cable clampers and the tapes to free the
cables
2. Disconnect the connectors (P2, P6, P11, P35, P52, P56
and P58).
3. Remove the screws (
×6
) and remove the P(MAIN)-
Board.
9.2.10. Remove the P(SUB)-Board
Caution:
To remove P.C.B. wait 1 minute after power was off for
discharge from electrolysis capacitors.
discharge from electrolysis capacitors.
1. Unlock the cable clampers and the tapes to free the
cables
2. Disconnect the connectors (P51, P55 and P57).
3. Remove the screws (
3. Remove the screws (
×4
) and remove the P(SUB)-
Board.
28
9.2.11. Remove the A-Board
1. Unlock the hooks and the tapes to free the cables.
2. Disconnect the connectors (A1, A6, A8A and A12).
3. Disconnect the USB cables (JK8605 and JK8607).
4. Disconnect the flexible cables (A20, A31, A32 and A33).
5. Remove the screws (
2. Disconnect the connectors (A1, A6, A8A and A12).
3. Disconnect the USB cables (JK8605 and JK8607).
4. Disconnect the flexible cables (A20, A31, A32 and A33).
5. Remove the screws (
×4 ).
6. Remove the Side shield metal and the Bottom shield
metal.
7. Remove the A-Board.
8. Remove the screws (
×5 ).
9. Remove the Heatsinks (bottom-1, -2), the Thermal
conductive sheets and the Heat rubber.
9.2.12. Remove the Control unit assy
1. Unlock the tape to free the cables.
2. Disconnect the connector (C14).
3. Remove the claws (
2. Disconnect the connector (C14).
3. Remove the claws (
×2
) and remove the Control unit
assy.
9.2.13. Remove the Speaker SQs
1. Unlock the hooks and the tapes to free the cables.
2. Remove the screws (
2. Remove the screws (
×6
each) and remove the
Speaker covers (L, R).
3. Disconnect the Relay connector.
4. Remove the screws (
4. Remove the screws (
×2
each) and remove the
Speaker SQs (L, R).
Click on the first or last page to see other TX-P65VT60Y / TX-PR65VT60 service manuals if exist.