DOWNLOAD Panasonic CF-W5LWEZZBM Service Manual ↓ Size: 32.07 MB | Pages: 127 in PDF or view online for FREE

Model
CF-W5LWEZZBM
Pages
127
Size
32.07 MB
Type
PDF
Document
Service Manual
Brand
Device
PC / NOTEBOOK COMPUTER
File
cf-w5lwezzbm.pdf
Date
PREV: Panasonic CF-W5 (serv.man2) Service Manual / Parts change notice

Panasonic CF-W5LWEZZBM Service Manual ▷ View online

33
9.2.19.  Removing the Hinge Cover
Preparation : perform the section 9.2.1. to 9.2.4.
and 9.2.18. first.
1. Remove the 2 screws (Y) and then remove the hinge
cover (L, R).
Screw (Y) : DRHM0108ZA (N19)
2. The LCD front case and the combination parts of
LCD rear case are separated.
(Combination parts are 6 the top and bottom places
for each, 4 right and left places for each)
3. Remove the Hinge (L, R).
9.2.20. Removing the LCD Unit and the
LCD Rear
Preparation : perform the section 9.2.1. to 9.2.4.
and 9.2.18. to 9.2.19. first.
1. Remove the 2 screws (Z).
Screw (Z) : DXHM0076ZA (N18)
9.2.18.  Removing the LCD Unit
Preparation : perform the section 9.2.1. to 9.2.4.
first.
1. Remove the 2 screws (X).
Screw (X) : DXQT26+D5FNL (N15)
2. Remove the LCD cable from the connector (CN10),
(CN11), (CN28) of the main board.
CN10
CN11
CN28
Screw (X)
Screw (X)
LCD Cable
Bottom Case
Hinge Cover (R)
Hinge Cover (L)
Screw (Y)
Screw (Y)
LCD Unit
Screw (Z)
Screw (Z)
LCD Unit
Hook Position
HInge (L)
Hinge (R)
LCD Front
LCD Ruber
LCD Rear
LCD Unit
Screw (T)
Screw (T)
34
9.2.22. Removing the WWAN Antenna
Board (MAIN), (SUB)
Preparation : perform the section 9.2.1., 9.2.2.,1
9.2.4. and 9.2.13. to 9.2.18. to 9.2.20. and 9.2.22.
first.
1. Open the SIMM cover and then remove the 2
screws (a).
Screw (a) : DXHM0057ZA (N7)
2. Remove the antenna cover.
3. Peel off the LCD hold sheet.
LCD Hold Sheet : DFHR3E92ZA (K1013)
4. Peel off the 2 cable fixed sheets and cable blind
sheet.
Cable Fixed Sheet : DFHR8526ZA (K1023)
Cable Blind Sheet : DFGX0475ZA (K1016)
5. Remove the each 2 screws (b) and then remove the
antenna board (MAIN), (SUB).
Screw (b) : DFHE5025XA (N1)
9.2.21. Removing the Inverter Board
Preparation : perform the section 9.2.1., 9.2.2.,1
9.2.4. and 9.2.13. to 9.2.18. to 9.2.20.  first.
1. Remove the LCD Cable from the Inverter.
2. Peel off the Tape for fixation from Inverter Case.
3. Remove the Inverter with the Inverter Case.
LCD Hook
Gasket Cloth
Inverter Box
Tape
LCD Cable
LCD High voltage
2pin Wire Rod
LCD Front Case
LCD Rear
SIMM Cover
Screw (a)
Antenna Cover
Cable Fixed Sheet
Cable Blind Sheet
LCD Rear
LCD Hold Sheet
WWAN Antenna 
Board (MAIN)
WWAN Antenna 
Board (SUB)
Antenna 
Cable
Antenna 
Cable
Screw (V)
35
9.2.23. Removing the WWAN Board
Preparation : perform the section 9.2.1., 9.2.2.,1
9.2.4. and 9.2.13. to 9.2.18. to 9.2.20.  first.
1. Disconnect the WM cable from the connector
(CN1501).
2. Remove the 6 screws (c) and then remove the
WWAN board.
Screw (c) : DFHE5025XA (N1)
LCD Rear
CN1501
WM Cable
WWAN Board
LCD Rear
Screw (W)
Screw (W)
WWAN Board
36
9.3. Reassenbly instructions
9.3.1. Attention when CF-W5L series is repaired
- Please execute writing BIOS ID when you exchange the main board.
- Parts (sheet and rubber) etc.related various the conductive cloth and heat spreader cannot be recycled.Use
new parts.
9.3.2. Assembly knowhow of the LCD
9.3.2.1.  Assembly of the LCD Front
LCD rubber
Affixation of LCD rubber / LCD BATT rubber / LCD BATT rubber
Paste side
Affixes between ribs
Put in the 
length wall
LCD front
LCD front panel
LCD front Wan
Be parallel after Affixes
Width:Largeness
Width:Smallness
LCD side rubber
LCD rubber
Running aground do not be in a surrounding rib
LCD side rubber
Running aground do not be in a surrounding rib
The above drawing
The above drawing
Drawing in the under
Drawing in the under
  The LCD rubber must not come in succession mutually.
  Running aground do not be in a surrounding rib
The space among is 0.4-0.6mm.
LCD BATT rubber
Page of 127
Display

Click on the first or last page to see other CF-W5LWEZZBM service manuals if exist.

RANDOM: