DOWNLOAD Panasonic CF-W5LWEZZBM Service Manual ↓ Size: 32.07 MB | Pages: 127 in PDF or view online for FREE

25

1. End the Windows.
2. Turn off the power and then remove the AC adaptor.
3. Slide the hooks (A) and then remove the battery

Pack.

4. Remove the screw (A) and then remove the DIMM

cover.
(Remove if the DIMM memory is equipped with)
Screw (A) : XSB2+4FNL (N17)

1. Remove the 4 screws (B).

Screw (B) : DXQT2+E12FNL (N11)

2. Remove the keyboard hook plates,and then remove

the hook of back side of keyboard with screwdriver.

6. Remove the heat spreader from buttom of the

keyboard.

7. Remove the keyboard FFC from the connector

(CN15), (CN26) and then remove the keyboard.

3. The LCD unit is opened up to about 90 °by operating

the LCD knob.

4. Remove the 6 hooks (B).
5. Open the keyboard from LCD side and then turn it

inside out on the top case.

Screw (A)

DIMM cover

Battery Pack

Hook (A)

LCD Knob

Hook (B)

LCD unit

Hook (B)

Heat Spreader

CN26

Keyboard

CN15

Screw (B)

Screw (B)

Screw (B)

Keyboard Hook Plate

26

1. Insert a small screwdriver into the hole and slide the

look in the direction shown by arrow (C) to open the
disc cover.

2. The anttena cover (R) is rotated from the bottom

case side in the direction of arrow (A) and the
antenna cover (R) removed in the direction of arrow
(B).

3. Remove the 3 screws (D), 2 screws (E) and 3

screws (F) from the bottom case.
Screw (D) : DRHM0092ZA (N4)
Screw (E) : DXHM0057ZA (N7)
Screw (F) : DXHM0039ZA (N6)

1. Remove the 2 screws (C).

Screw (C) : DFHE5025XA (N1)

2. The slide is done in the direction of the arrow and

the HDD cover is removed.

3. Lift up the HDD unit and remove FFC connector and

then remove the HDD unit.

4. HDD is taken out of the HDD case.

Please do not bend pins of the HDD connector, at the
time of removing HDD and FFCconnector.

Screw (C)

HDD Cover

HDD

FFC Connector

HDD Unit

HDD FFC

HDD Case

LCD unit

Antenna cover (R)

A

B

C

Small 
screwdriver

Hole

Back Side

Screw (F)

Screw (E)

Screw (F)

Screw (D)

Screw (F)

Screw (D)

Screw (D)

Screw (E)

27

1. Peel off the tape.
2. Remove the solenoid cable.
3. Remove the 1 screw (M) and then remove the SW

board.
Screw (M) : DXHM0057ZA (N7)

Note it that the disc eject knob comes off at the same
time.

4. Remove the 3 screws (G), 2 screws (H), 2 screws

(I), 2 screws (J), 2 screws (K) and 1 screw (L) from
the top case.
Screw (G) : DXQT2+E6FNL (N13)
Screw (H) : DXQT26+D8FCL (N16)
Screw (I) : DXQT2+E6FCL (N12)
Screw (J) : DFHE5025XA (N1)
Screw (K) : DXQT2+E12FNL (N11)
Screw (L) : DXQT2+E6FNL (N13)

5. Lift up the top case, remove the pad FFC and then

remove the top case.

Screw (H)

Screw
(H)

Screw (G)

Screw (G)

Screw
 (K)

Screw (K)

Screw (J)

Screw (I)

Screw (I)

Screw
(G)

Disc Cover

Screw 
(S)

Screw (J)

FFC (SW) 

Top Case

FFC (PAD)

Top Case

Screw (Q)

Disc Eject Knob

Switch Board

Solenoid Cable

Tape

28

1. Remove the 1 screw (N) of the disk angle.

Screw (N) : DXHM0057(N7)

2. Slide the disc cover to the disc cover shaft and

remove the cover.

3. The disk cover shaft is pulled out while sliding and

removed it from the disk angle in the direction of the
touch pad.

1. Peel off the tape.
2. The 5 hooks of the pad cover are depressed in the

direction of the center of the touch pad by using the
small screwdriver.

3. Remove the hooks of the toutch pad and the Pad

button, and remove the touch pad.

Disc Cover

Disk Cover Shaft

Top Case

Disc Cover Spring

Disk Angle

Screw (N)

Tape

Hook

Hook

Hook

Hook

PAD FFC

Top Case

Hook

PAD Cover

Touch Pad

PAD Button