Panasonic CF-T5LWETZBM Service Manual ▷ View online
29
9.2.14. Removing the Hinge Cover
Preparation : perform the section 9.2.1., 9.2.2.,
9.2.4. and 9.2.13. first.
9.2.4. and 9.2.13. first.
1. Remove the 2 screws (R) and then remove the
hinge cover (L, R).
Screw (R) : DRHM0108ZA (N1002)
Screw (R) : DRHM0108ZA (N1002)
Hinge Cover (R)
Hinge Cover (L)
Screw (R)
Screw (R)
LCD Unit
Screw (S)
Screw (S)
LCD Unit
Hook Position
HInge (L)
Hinge (R)
LCD Front
LCD Ruber
LCD Rear
LCD Unit
Screw (T)
Screw (T)
2. Remove the 2 screws (S).
Screw (S) : DRHM0076ZA (N1001)
9.2.15. Removing the LCD Unit and the
LCD Rear
Preparation : perform the section 9.2.1., 9.2.2.,
9.2.4. and 9.2.13. to 9.2.14. first.
9.2.4. and 9.2.13. to 9.2.14. first.
1. Remove the 2 LCD Ruber and then remove the 2
screws (T).
Screw (T) : DXHM0039ZA (N5)
Screw (T) : DXHM0039ZA (N5)
2. Separate the LCD front and the LCD rear.
3. Remove the hinge (L), (R).
3. Remove the hinge (L), (R).
LCD Hook
Inverter Box
Inverter Tape
LCD Cable
LCD High voltage
2pin Wire Rod
2pin Wire Rod
LCD Front
Conductive Cloth
(LCD Cable)
(LCD Cable)
9.2.16. Removing the Inverter
Preparation : perform the section 9.2.1., 9.2.2.,
9.2.4. and 9.2.13. to 9.2.15. first.
9.2.4. and 9.2.13. to 9.2.15. first.
1. Remove the LCD cable from the inverter.
2. Peel off the conductive cloth (LCD cable) from the
2. Peel off the conductive cloth (LCD cable) from the
inverter.
3. Peel off the inverter tape from the inverter.
Inverter tape : DFHR3A95ZA (K49)
3. Remove the inverter with inverter box.
30
9.2.17. Removing the WWAN Antenna
Board (MAIN), (SUB)
Board (MAIN), (SUB)
Preparation : perform the section 9.2.1., 9.2.2.,
9.2.4. and 9.2.13. to 9.2.15. first.
9.2.4. and 9.2.13. to 9.2.15. first.
1. Open the SIMM cover and then remove the 2
screws (U).
Screw (U) : DXHM0057ZA (N7)
Screw (U) : DXHM0057ZA (N7)
2. Remove the antenna cover.
3. Peel off the LCD hold sheet.
LCD Hold Sheet : DFHR3E92ZA (K1028)
4. Peel off the 2 cable fixed sheets and cable blind
sheet.
Cable Fixed Sheet : DFHR8526ZA (K1030)
Cable Blind Sheet : DFGX0475ZA (K1003)
Cable Fixed Sheet : DFHR8526ZA (K1030)
Cable Blind Sheet : DFGX0475ZA (K1003)
5. Remove the each 2 screws (V) and then remove
the antenna board (MAIN), (SUB).
Screw (V) : DFHE5025XA (N1)
Screw (V) : DFHE5025XA (N1)
9.2.18. Removing the WWAN Board / LCD
Hook WAN
Preparation : perform the section 9.2.1., 9.2.2.,
9.2.4. and 9.2.13. to 9.2.15., 9.2.17. first.
9.2.4. and 9.2.13. to 9.2.15., 9.2.17. first.
1. Disconnect the WM cable from the connector
(CN1501).
2. Remove the 6 screws (W) and then remove the
WWAN board.
Screw (W) : DFHE5025XA (N1)
Screw (W) : DFHE5025XA (N1)
LCD Rear
SIMM Cover
Screw (U)
Antenna Cover
Cable Fixed Sheet
Cable Blind Sheet
LCD Rear
LCD Hold Sheet
WWAN Antenna
Board (MAIN)
Board (MAIN)
WWAN Antenna
Board (SUB)
Board (SUB)
Antenna
Cable
Cable
Antenna
Cable
Cable
Screw (V)
LCD Rear
CN1501
WM Cable
WWAN Board
LCD Rear
Screw (W)
Screw (W)
WWAN Board
31
9.3. Reassenbly instructions
9.3.1. Attention when CF-T5L series is repaired
- Please execute writing BIOS ID when you exchange the main board.
- Parts (sheet and rubber) etc.related various the conductive cloth and heat spreader cannot be recycled.Use
- Parts (sheet and rubber) etc.related various the conductive cloth and heat spreader cannot be recycled.Use
new parts.
9.3.2. Assembly knowhow of the LCD
9.3.2.1. Assembly of the LCD Front
5mm
5mm
5mm
Table (reception desk cabinet side) respect
FRONT TP CUSHION A
FRONT TP CUSHION B
TOUCHPANEL
TOUCHPANEL
FRONT TP CUSHION C
FRONT TP CUSHION D
FRONT TP CUSHION D
FRONT TP CUSHION D
FRONT TP CUSHION D
FRONT TP CUSHION D
FRONT TP CUSHION D
Back (LCD side) respect
The glass
switching off
lack part
switching off
lack part
The glass
switching off
lack part
switching off
lack part
In a two sided tape, long one is a
Flexible cable side.
Flexible cable side.
Affixation of LCD Front TP CUSHION/A/B/C/Tape
9.3.2.2. Putting Front TP Cushion
Does not run aground
in a surrounding rib.
in a surrounding rib.
Does not run aground
in a surrounding rib.
in a surrounding rib.
-LCD Batt Rubber does not overlap.
-Does not run aground in a surrounding rib.
-Does not run aground in a surrounding rib.
draw on
draw to the under
Space between LCD
Batt Rubber
Batt Rubber
LCD Side Rubber
LCD Batt Rubber
LCD Batt Rubber
LCD Front WAN
Affixes between ribs.
Paste side
LCD Magnet
When affixing, the tool is used.
Puts in the length wall.
Puts in the length wall.
-LCD Side Rubber, LCD Batt Rubber and LCD Magnet are not put out from the concave part.
-It is noted that the finger does not touch the paste side when there are put.
-It is noted that the finger does not touch the paste side when there are put.
32
9.3.2.4. Putting LCD Side Dumpers
9.3.2.3. Putting TP Flexible Protection Tape
LCD
Side Dumper
LCD
LCD insulator
LCD insulator
Put the Side Dumper
There is a possibility to destroy the prism lens
when pressurizing too much when the both sides
tape is affixed
when pressurizing too much when the both sides
tape is affixed
The rib match of thick one.
The edge side match of a thick part.
Overflow NG to the rear side in front of overflow OK
Substrate externals
standard
standard
Frame externals
standard
standard
LCD
Side Dumper
TP Flexible cable
protection tape
protection tape
Sub-materials tape 30mm
The tape is turned inside out.because
the tape of the sub-materials begins to
see from Flexible cable is turned as
shown,sticking side is lost.
the tape of the sub-materials begins to
see from Flexible cable is turned as
shown,sticking side is lost.
Upper : The tape is matched to the edge
of the glass. It does not overflow.
Right and left :
The tape is matched to Flexible cable’s
right edge.It does not overflow.
of the glass. It does not overflow.
Right and left :
The tape is matched to Flexible cable’s
right edge.It does not overflow.
Upper :
Near in the under putting of
tape.
Do not get on and do not go up.
Right and left :
It is matched to Flexible cable right edge.
it does not overflow.
Do not get on and do not go up.
Right and left :
It is matched to Flexible cable right edge.
it does not overflow.
Click on the first or last page to see other CF-T5LWETZBM service manuals if exist.