Panasonic CF-19FHGAXxM Simplified Service Manual ▷ View online
■ Assembly of Inverter PCB (Applicable Model : Touch Screen Model)
Inverter
Ass'y
Inverter
Ass'y
0
4mm
0
0.5mm
A
0
3mm
Connector
PWB
FPC
12
Confirm
the direction of the Inverter board when attaching.
30
35mm
Inverter
Ass'y
LCD
Back Dumper
LCD
Ass'y
Inverter
Mil Sheet
The
gap side is front.
0
1mm
Attach
coming over the end of steel plate by 1 to 2 mm.
Avoid
any stress on the Tab part of the
LCD
Module because the line comes off.
Wrap
of Antenna Cable
Cushion
E
Conductive
Tape
Wrap
over the Antenna Cable
Cushion
and the Cable.
6
2mm from the
branch
point
Connect
Fix
the two Cables
and
connector.
Insulation
Parts
Insulation
Parts
Insulation
Parts
Insulation
Parts
Note
for attaching Conductive Tape
Conductive
Tape
Tape
Connect
the Cable to the
left
and right Connectors.
LCD
Cable TS
Attach
the Inverter Ass'y in the
middle
of right and left.
Attach
the surplus of the right and left sides on the
Back
Dumper as shown below and overlap on the
CCFL
Cable. Attach the Pet Sheet over the Core.
LCD
Side Cushion E
LCD
Side Cushion E
LCD
Side Cushion F
Insert
it between the ribs.
(Fit
to the Cabinet.)
Insert
it between the ribs.
(Fit
to the Cabinet.)
Insert
it between the ribs.
(Fit
to the Cabinet.)
Cushion
High
Voltage
Label
TS
PWB
Connect
Attach
it to the Connector and FPC.
Avoid
getting under the Sheet.
Sield
Sheet
Wind
round the LCD Cable
a
few times and attach it.
Avoid
any stress on the Cable
when
connecting it.
Hold
the Connector part when
connecting/disconnecting.
Sub
material: Pet Tape 1
Ensure
the edge of the
conductive
fabric is not
frayed.
Details
of "A"
1
2
mm
Avoid
any stress on the Cable when
connecting
the CCFL Cable.
Hold
the Connector part when
connecting/disconnecting.
Inverter
Ass'y
S2
Details
of cable
Avoid
running over the rib
CAUTION
S1:Insulation
S2:Pinching Cables S3:Sharp Edge
S4:Part
No. Check S5:Others
Safety
Working
S5
33 / 90
■ Assembly of Inverter PCB (Application Model : Digitizer Model)
Inverter
Ass'y
LCD
Back Dumper
Conductive
Tape
0
1mm
Attach
coming over the end of steel plate by 1 to 2 mm.
S2
Details
of cable
Avoid
running over the rib
0
0
CAUTION
S1:Insulation
S2:Pinching Cables S3:Sharp Edge
S4:Part
No. Check S5:Others
Safety
Working
S5
34 / 90
■ Assembly of Touch Screen (Applicable Model : Touch Screen Model)
Avoid
running over.
Attach
the surface to the LCD Front.
Apply
the load 20 to 30N (2.0 to 3.0 Kgf) to the Cushions.
(Note)
OK
NG
T/S
T/S
Touch
Screen Ass'y
Attach
it to the front side.
(Using
the jig)
Dimensional
tolerance: 0.2
Details
of "A"
6
0.5mm
0
0.5mm
0
1mm
0
1mm
0
1mm
0
1mm
Back
Side
Match
to the wall of the
Cabinet.
0 to 0.5 mm
Match
to the marking line.
0.5 mm
Match
to the marking line.
0.5 mm
Ensure
4 and 5 do not run over the display side.
Touch
Screen Ass'y
Touch
Screen
Protect
Sheet
TS
FPC
Spacer
TS
Spacer A
TS
Spacer A
TS
Spacer B
TS
Spacer B
LCD
Side Cushion B
A
Laminate
Laminate
35 / 90
■ Assembly of Glass (Applicable Model : Digitizer Model)
9.2.3.
Assembling
the WWAN Main Antenna PCB, LAN-Main BT Antenna PCB, LAN AUX
Antenna
PCB, WWAN AUX Antenna PCB and Pen holder
1. Fix
the Pen Holder using the 2 Screws. <K10-1-13>
2. Attach
the Pen.
3. Fix
the WWAN AUX Antenna PCB using the 2 Screws.
<N1>
4. Fix
the LAN AUX Antenna PCB using the 2 Screws. <N1>
5. Fix
the LAN-Main BT Antenna PCB using the 2 Screws.
<N1>
6. Fix
the WWAN Main Antenna PCB using the 2 Screws.
<N1>
Screws
<N1> : DFHE5025XA
Screws
<K10-1-13> : DRHM5025YAT
<K10-1-13>
<N1>
<N1>
<N1>
<N1>
<K10-1-13>
Pen
Holder
LAN
Aux
Antenna
PCB
WWAN
Main
Antenna
PCB
Pen
WWAN
Aux
Antenna
PCB
<N1>
<N1>
<N1>
<N1>
LAN-Main
BT
BT
Antenna PCB
36 / 90
Click on the first or last page to see other CF-19FHGAXxM service manuals if exist.