DOWNLOAD Panasonic CF-18NHHZXBM Service Manual ↓ Size: 6.14 MB | Pages: 95 in PDF or view online for FREE

7-2

3. Remove the KBD Plate.

4. Lift the far side of the Keyboard and slide it to backward,

and then turn the Keyboard over frontward.

5. Remove the three Screws <C>.
6. Remove the KBD Connector Cover.

7. Disconnect the Cable from Connector (CN18).
8. Remove the Keyboard.

9. Remove the TP Tape.

10. Disconnect the Cable from Connector (CN800).

11. Remove the Touch Pad and Click Button Plate.

Screws <B>:DRSB2+5FKL
Screws <C>:DFHE5025XA

1. Remove the four Screws <D>.
2. Disconnect the Cable from Connector (CN37).
3. Remove the DIMM Lid.
4. Remove the two Screws <E>.
5. Remove the Speaker Angle.

Screws <D>: DRQT2+D2FKL
Screws <E>: DRHM5025YA

1. Remove the thirteen Screws <F>.
2. Open the LID Rubbers.
3. Remove the Rear Cabinet.

Screws <F>:DRHM0061ZA

1

2

Keyboard

<C>

KBD

Connector

Cover

Keyboard

Keyboard 

FPC

Connector

 (CN18)

Connector

(CN800)

TP Tape

Touch Pad

Click Button

Plate

<D>

DIMM LID Sheet

DIMM Lid

Speaker Unit

Speaker

Waterproof

Sheet

Speaker Washer

Speaker Angle

Connector (CN37)

Speaker Cable

Tube

<E> <D>

<D>

<E><D>

<F>

<F>

<F>

<F>

<F>

<F>

<F>

<F>

<F>

<F>

<F>

<F>

<F>

7-3

1. Remove the five Screws <G>.
2. Remove the DU Lid Angle and DU Lid.

Screws <G>:DRHM5025YA

1. Remove the two Screws <H>.
2. Disconnect the Cable from a Connector (CN901).
3. Remove the Audio PCB.

Screws <H>:DRSB2+5FKL

This procedure is not necessary if the computer is not
equipped with Wireless Module or Modem PCB.

1. Disconnect the two Antenna Cables from two Connectors

(J5, J6).

2. Remove the Wireless Module.
3. Remove the three Screws <I>.
4. Remove the Port PCB.
5. Remove the two Screws <J>.
6. Remove the Modem.
7. Disconnect the Modem cable from the connector.
8. Remove the two Screws <K>.
9. Remove the BAT CON angle.

Screws <I>:DRSB2+5FKL
Screws <J>:XSB2+4FNL
Screws <K>:DRSB2+5FKL

1. Disconnect the Cable from Connector(CN21).
2. Remove the three Screws <h>
3. Remove the SD PCB.

Screws <h>:DXQN2+A22FNL

<G>

<G>

<G>

<G>

<G>

DU LID

DU LID Angle

Connector (CN901)

Audio PCB

<H>

<K>

<J>

<K>

<I>

<I>

Bat Con Angle

Connector (J5)

Connector (J6)

Modem

Port PCB

Wireless Module

<I>

<J>

<h>

<h>

<h>

SD PCB

Connector (CN21)

7-4

1. Disconnect the Cable from Connector(CN3).
2. Remove the Lithium Battery.
3. Disconnect the seven Cables from seven Connectors

(CN9, CN12, CN14, CN23, CN30, CN35, CN36).

4. Remove the Screw <L>.
5. Remove the two Screws <M>.
6. Disconnect the two Cables from two Connectors (CN8,

CN17).

7. Remove the four Screws <N>.
8. Remove the Main PCB.
9. Remove the PCMCIA Unit.

Screw <L>:DRSB2+5FKL
Screws <M>:DXYN2+J12FNL
Screws <N>:DXYN2+J18FNL

1. Disconnect the Cable from Connector (CN801).
2. Remove the three Screws <O>.
3. Remove the PAD PCB.
4. Remove the four Screws <P>.

5. Remove the two Screws <Q>.
6. Remove the I/O PCB.

Screws <O>:DFHE5025XA
Screws <P>:DFHE5058ZB
Screws <Q>:DRSB2+5FKL

1. Remove the LED Waterproof Sheet.
2. Remove the LED PCB.
3. Remove the Switch PCB.
4. Remove the Power Switch.

1. Remove the three Screws <R>.
2. Remove the CPU Heat Plate.

Screws <R>:DFHE5025XA

<L>

<M><M>

<N>

<N>

<N>

<N>

HDD Guid Plate

Connector (CN36)

Connector (CN35)

Connector (CN30)

PCMCIA Unit

to Connector (CN17)

Connector (CN3)

Connector (CN17)

Connector (CN8)

Connector (CN9)

Connector (CN14)

Connector (CN12)

LAN Cable

Main PCB

to Connector (CN8)

Connector

(CN23)

Lithium Battery

<O><O>

<O>

<Q>

<P>

<Q>

I/O PCB

PAD PCB

Connector 

(CN801)

LED Waterproof Sheet

LED PCB

Power 

Switch 

Knob

Operation Sheet

Switch PCB

<R>

<R>

<R>

CPU Heat Plate

7-5

1. Remove the four Screws <S>.
2. Remove the LCD Hinge Cover.

3. Display unit is half-rotated and removes the two Screws

<T>.

4. Remove the four Screws <U>.

5. Turn the computer over.
6. Remove the Display Unit.

Screws <S> : DFHE5025XA
Screws <T> : DRSB2+5FKL
Screws <U> : DXYN4+J8FNL

1. Remove the eight Screws <V> on the front side of Display

unit.

2. Remove the eight Screws <V> on the back side of Dis-

play unit.

3. Remove Antenna Cover and Tablet Latch Cover.
4. Remove the two Screws <W>.
5. Remove the ten Screws <X>.
6. Remove the LCD Rear Case.

Screws <V> : DRQT26+E5FKL
Screws <W> : DXYN3+J10FNL
Screws <X> : DXYN2+J6FNL

1. Remove the Cable Holder.
2. Remove the two Screws <Y>.
3. Remove the Cable Holder Plate and LCD Hinge.

Screws <Y> : DXYN3+J8FNL

<S>

<S>

LCD Hinge Cover

<S>

<S>

<T>

<T>

Hinge Cover

<U> <U>

<U>

<U>

<X>

<X>

<X>

<X>

<X>

<W>

<W>

<X>

<X>

<X>

<X>

<X>

<V>

<V>

<V>

<V>

<V>

<V>

<V>

<V>

Antenna Cover

Tablet Latch Cover

LCD Rear Case

Antenna Cover

<V>

<V>

<V>

<V>

<V>

<V>

<V>

<V>

<Y>

<Y>

LCD Cable

Holder

Sheet

Cable

Holder

Cable

Holder

Cable

Holder

Plate

Cable Holder

Plate

Cable

Holder

Plate

LCD

Hinge