Panasonic UB-T780 Service Manual ▷ View online
13
UB-T780
3.3.
Included Accessories
Confirm that the following items are included with the elite Panaboard.
Note
• Screws (8 count) for wall mounting are not included. Please purchase screws with a size of M6, appropriate for type of wall.
(Refer to section 3.4.3 Wall Types and Installation Procedures.)
14
UB-T780
3.4.
Wall Mounting Construction
3.4.1.
Checking the Wall
When mounting on a wall, consult with your building's owner,
caretaker or construction manager to determine if the wall
strength is sufficient to install the elite Panaboard. For safety,
install the elite Panaboard only after thoroughly understanding
the type of walls, the appropriate types of screws and the con-
struction method.
Caution
caretaker or construction manager to determine if the wall
strength is sufficient to install the elite Panaboard. For safety,
install the elite Panaboard only after thoroughly understanding
the type of walls, the appropriate types of screws and the con-
struction method.
Caution
Do not attach the electronic board to mortared walls. Acci-
dental electric leakage from the wall mounting plate bolts to
metal laths or wire laths can cause heat, smoke or a fire.
dental electric leakage from the wall mounting plate bolts to
metal laths or wire laths can cause heat, smoke or a fire.
I. Necessary Tools and Parts
(not included with the elite Panaboard)
Drill, Screwdriver, Measuring tape, Level,
8 screws (M6 size)
8 screws (M6 size)
II. Before Starting
1. Make sure that the wall is strong enough to support the
elite Panaboard.
greater than 1324 N (135 Kgf)
Notice
greater than 1324 N (135 Kgf)
Notice
• If necessary, reinforce the wall so that it is strong enough
to support the elite Panaboard.
2. Make sure that the location is large enough to accommo-
date the elite Panaboard.
Height: greater than 2000 mm (6 ft 7 in)
Width: greater than 1850 mm (6 ft 1 in)
Height: greater than 2000 mm (6 ft 7 in)
Width: greater than 1850 mm (6 ft 1 in)
3. Make sure that the AC outlet is within 3 m (9 ft 10
3
/
8
in) of
where the elite Panaboard will be mounted and that it will
not be behind the elite Panaboard.
not be behind the elite Panaboard.
3.4.2.
Installing the Wall Mounting Plates
1. Ensure that the wall is strong enough to support the elite
Panaboard.
Rated strength: greater than 1324 N (135 Kgf)
Rated strength: greater than 1324 N (135 Kgf)
2. Using the measuring tape and level, mark the 8 locations
to insert the screws.
Note
• The dotted line in the illustration represents the outer
edge of the elite Panaboard.
3. Drill 8 holes for the wall mounting plates.
• Drill holes appropriate for the screws you are using.
4. Install the wall mounting plates using the 4 screws.
• 2 screws are used for each wall mounting plate.
The remaining 4 screws are used after installing the elite
Panaboard on the wall.
Panaboard on the wall.
• Screws (8 count) are not included with the elite Pana-
board. Please prepare screws with a size of M6, appro-
priate for type of wall.
priate for type of wall.
• Tighten the bolt so that it will not become loose.
• When drilling the holes and installing the wall mounting
• When drilling the holes and installing the wall mounting
plates, follow the procedure in the section 3.4.3 “Wall
Types and Installation Procedures”
Types and Installation Procedures”
5. Mount the elite Panaboard on the wall.
Refer to the section 3.6 “Assembling the elite Pana-
board”.
board”.
15
UB-T780
3.4.3.
Wall Types and Installation Procedures
The method for attaching the wall mounting plates to the wall will vary depending on the wall's structure.
Three available options are listed below.
Other methods may be necessary depending on the wall.
<Metal or Concrete walls>
Three available options are listed below.
Other methods may be necessary depending on the wall.
<Metal or Concrete walls>
Stud plug (not included) are needed.
<Plasterboard walls>
Split-wing toggles (not included) are needed.
<Wooden walls>
Wood screws (not included) are needed.
Drill eight holes in the wall.
For the correct hole size, refer to the instructions for the particular stud plugs used.
For the correct hole size, refer to the instructions for the particular stud plugs used.
Insert the bolt through the hole in the wall mounting plate and tighten until the wall
mounting plate is securely fixed to the wall.
mounting plate is securely fixed to the wall.
Insert the bolt through the hole in the wall mounting plate and into the hole in the wall
so that the arms of the split-wing toggle are horizontal.
For the correct hole size, refer to the instructions for the particular split-wing toggles
used.
so that the arms of the split-wing toggle are horizontal.
For the correct hole size, refer to the instructions for the particular split-wing toggles
used.
After the arms expand, pull the wall mounting plate out until the arms of the split-wing
toggle grip firmly into the wall.
toggle grip firmly into the wall.
Tighten the bolt until the wall mounting plate is securely fixed into the wall.
Insert the wood screws through the hole in the wall mounting plate and tighten until
the wall mounting plate is securely fixed to the wall.
For the correct hole size, refer to the instructions for the particular wood screws used.
the wall mounting plate is securely fixed to the wall.
For the correct hole size, refer to the instructions for the particular wood screws used.
16
UB-T780
3.5.
Preparing for Removing the elite Panaboard from Its Packaging
Open the box, remove the accessory box, and open the plastic cover of the elite Panaboard.
Note:
•
When handling the screen board, hold it by the edge frame and not the screen board itself. (Holding the screen board can result in damage.)
•
The packing materials in the shipping box are necessary for repackaging, so keep them in a safe place.
Click on the first or last page to see other UB-T780 service manuals if exist.