Panasonic UB-5838C / UB-5338C Service Manual ▷ View online
21
3.4.
Operation Check and Settings before using Panaboard
3.4.1.
Before Operation Check
Note:
1. Do not wipe the screen film surface with paint thinner,
benzene, or cleaners that contain abrasives. Doing so
may cause discoloration.
may cause discoloration.
2. Do not wipe the screen film surface with a dry cloth.
Doing so may create static electricity.
3.4.2.
Setting the time
1.
Wipe the screen film surface.
• Soak a soft cloth with water, wring well, and wipe the screen
film surface.
2.
Attach the Power Cord.
• Securely fit the included Power Cord in the AC inlet of the
control box.
3.
Remove the battery protection sheet.
1.
Turn the power switch on.
• The time set-up screen is displayed automatically when the
power switch is turned on for the first time.
If the time set-up screen is not displayed even when the power
switch is turned on, push the Set-up Key on the Control Panel
If the time set-up screen is not displayed even when the power
switch is turned on, push the Set-up Key on the Control Panel
to enter the setting mode, then push the Set-up Key (
)
repeatedly to select the time set-up mode, and then push the
Advance Key (
).
2.
Set the current time.
• The value can be changed by pushing the Set-up Key (
),
and select the setting by pushing the Advance Key (
).
3.
Push the Mode Key (
) to set the time.
22
3.4.3.
Operation Check Procedure
After assembling the unit and setting the time, perform the procedures presented in the following table to make sure it functions
properly.
properly.
23
3.5.
Repacking
Perform the above Assembly Steps Sec.3.3.1 to Sec3.3.5 in reverse order to repack the unit and accessories.
Note:
Note:
When handling the screen unit, grasp the side cover on either side of screen. Do not grasp the screen film surface, as this may
scratch it.
scratch it.
24
3.6.
Wall Mounting Construction
3.6.1.
Checking the wall
When mounting on a wall, consult with your building’s owner, caretaker or construction manager to determine if the wall strength is
sufficient to install this unit. For safety, install this unit only after thoroughly understanding the type of walls, the appropriate types of
screws and the construction method.
Caution:
sufficient to install this unit. For safety, install this unit only after thoroughly understanding the type of walls, the appropriate types of
screws and the construction method.
Caution:
Do not attach the electronic board to mortared walls. Accidental electric leakage from the Wall-mounting Fixture screws to metal
laths or wire laths can cause heat, smoke or fire.
laths or wire laths can cause heat, smoke or fire.
3.6.1.1.
Necessary Tools and Parts (not included with the product)
(1) Drill
(2) Screwdriver
(3) Measuring tape
(4) Level
(5) 8 screws (M6 size)
(2) Screwdriver
(3) Measuring tape
(4) Level
(5) 8 screws (M6 size)
3.6.1.2.
Before Starting
1. Make sure that the wall is strong enough to support the following weight.
For UB-5838C: 1,373 N [140 kgf (309 lbf)]
For UB-5338C: 1,275 N [130 kgf (287 lbf)]
Note:
For UB-5338C: 1,275 N [130 kgf (287 lbf)]
Note:
If necessary, reinforce the wall so that it is strong enough to support the unit.
2. Make sure that the location is large enough to accommodate the unit.
For UB-5838C: 1,125 mm (H)
×
1,998 mm (W) [3' 8 19/64" (H)
×
6' 6 43/64" (W)]
For UB-5338C: 1,125 mm (H)
×
1,636 mm (W) [3' 8 19/64" (H)
×
5' 4 27/64" (W)]
3. Make sure that the AC outlet is within 3 m (9' 10 1/8") of where the unit will be mounted and that it will not be behind the unit.
Click on the first or last page to see other UB-5838C / UB-5338C service manuals if exist.