Panasonic KV-SS905C / KV-SS905CCN Service Manual / Supplement ▷ View online
Section No.
(Original Service
Manual)
Title on this Supplement
Main Contents
Remarks
11
9.2 “Section 11.3 Explanation of Connector“ (Modification)
Modify the description for the signal.
SPD Interrupt
SPD Interrupt
SPC Interrupt
C
14
10 “SECTION 14 PARTS LOCATION AND
MECHANICAL PARTS LIST“
MECHANICAL PARTS LIST“
(Addition & Modification)
Add the Power Cord for China, and others.
Add the Power Cord for China, and others.
B
15
11 “SECTION 15 REPLACEMENT PARTS
LIST“
LIST“
(Modification)
Modify Part No. on MAIN and I/F(SCSI) Boards.
Modify Part No. on MAIN and I/F(SCSI) Boards.
B
5
KV-SS905C / KV-SS905CCN
2 "SECTION 1 GENERAL PRECAUTION"
2.1.
"Section 1.2 Electrical Tests"
1. Unplug the power cord and check for continuity between the earth ground connection on the plug and the Interface Board
Cover. There should be zero ohm resistance.
2. With the unit unplugged, short the AC live-neutral of the plug with a jumper wire.
3. Turn ON the power switch.
4. Measure the resistance value with an ohmmeter between the jumpered AC plug and an exposed metal cabinet part, such as
screwheads, etc. (Refer to Fig.2)
Note
Some exposed parts may be isolated from the chassis by design. They read infinity.
5. If the measurement is less than 1M
, a possibility for electric shock may exit.
Note
This hazardous condition must be corrected before the unit is returned to the end user.
Fig. 1
Fig. 2
6
KV-SS905C / KV-SS905CCN
3 "SECTION 4 INSTALLATION"
3.1.
"Section 4.6.5 Color (Simplex / Duplex)"
Size
Resolution (dpi)
100
200
300
400
A3
0 / 0
0 / 0
0 / 64
64 / 128
A4
0 / 0
0 / 0
0 / 0
0 / 64
A5
0 / 0
0 / 0
0 / 0
0 / 0
A6
0 / 0
0 / 0
0 / 0
0 / 0
B4 (JIS)
0 / 0
0 / 0
0 / 64
64 / 128
B5 (JIS)
0 / 0
0 / 0
0 / 0
0 / 64
B6 (JIS)
0 / 0
0 / 0
0 / 0
0 / 0
Ledger
0 / 0
0 / 0
0 / 64
64 / 128
Legal
0 / 0
0 / 0
0 / 0
0 / 64
Letter
0 / 0
0 / 0
0 / 0
0 / 64
3.2.
"Section 4.10 Connecting the Unit to a Personal Computer"
Note
*AC cord shown on the figure is for AC100-120V.
Be sure to use a SCSI Cable as short as possible, covered with shield.
Caution
Set the Power Switch on the scanner and on the personal computer to OFF before connecting the interface cable. Use
only the AC Cord that is supplied by manufacturer.
only the AC Cord that is supplied by manufacturer.
3.3.
"Section 4.11 System Requirements"
When using the scanner, the required personal computer conditions are as follows.
CPU
Pentium 266MHz or higher (Pentium
, 1GHz processor or higher is recommended.)
Memory
64 MB or higher (256 MB or higher is recommended.)
OS
Windows
®
95 / Windows
®
98 / Windows NT
®
/ Windows
®
2000 / Windows
®
Me / Windows
®
XP
I/F Board (SCSI Board)
Adaptec Board SCSI card AHA2940UW / 29160 / 39160 Series are recommended.
*The scanning speed differs depending on the personal computer’s operating environment or application.
7
KV-SS905C / KV-SS905CCN
3.4.
"Section 4.13.2 Setting the ADF Selector"
(1)
When scanning normal paper [64 to 75 g/m
2
(17 to 20 lbs.)],
set the ADF selector to "3".
(2)
When scanning thick paper or smooth sided paper, set the
ADF selector to "4" or "5" .
ADF selector to "4" or "5" .
(3)
When scanning thin paper or rough face paper, set the ADF
selector to "1" or "2" .
selector to "1" or "2" .
8
KV-SS905C / KV-SS905CCN
Click on the first or last page to see other KV-SS905C / KV-SS905CCN service manuals if exist.