Panasonic KV-S7075C (serv.man2) Service Manual ▷ View online
97
9.3.3.
Scanner Information
This function provides various types of scanner information to the user or service-person. The main contents are as follows:
1. Model
2. Firmware Version
3. Board and Gate Array (LSI) versions
4. Memory size for front and back
5. Interface
6. Pre-imprinter condition
2. Firmware Version
3. Board and Gate Array (LSI) versions
4. Memory size for front and back
5. Interface
6. Pre-imprinter condition
9.3.4.
Scanner Counter
Item
Operation
Default
Remarks
Update All
Counters
Counters
1. Click “Update All Counters” to update the counters’ values.
2. Confirm the value of the “System”, “Flatbed”,
“After Clean Roller”, and “After Replace Roller” are also
updated on the main menu (Service Utility).
2. Confirm the value of the “System”, “Flatbed”,
“After Clean Roller”, and “After Replace Roller” are also
updated on the main menu (Service Utility).
—
Clear Counter
(After Clean
Roller)
(After Clean
Roller)
1. Click “Clear Counter” for “After Clean Roller” on the main
menu.
2. According to the message on the display, click “OK” to clear
the cleaning roller counter.
3. Confirm that the counter value is zero on the main menu.
menu.
2. According to the message on the display, click “OK” to clear
the cleaning roller counter.
3. Confirm that the counter value is zero on the main menu.
—
After cleaning rollers (Paper
Feed, Separation, and DFP
Rollers), execute this item.
Feed, Separation, and DFP
Rollers), execute this item.
Clear Counter
(After Replace
Roller)
(After Replace
Roller)
1. Click “Clear Counter” for “After Replace Roller” on the
main menu.
2. According to the message on the display, click “OK” to clear
the roller replacement counter.
3. Confirm that the counter value is zero on the main menu.
main menu.
2. According to the message on the display, click “OK” to clear
the roller replacement counter.
3. Confirm that the counter value is zero on the main menu.
—
After replacing rollers (Paper
Feed, Separation, and DFP
Rollers), execute this item.
Feed, Separation, and DFP
Rollers), execute this item.
98
9.3.5.
Scanner Condition
Item
Operation
Default
Remarks
Sleep Mode
1. Click “Sleep Mode” on the main menu (Service Utility).
2. Set “Waiting Time” (Unit: minutes) to specify the amount of
time until the scanner enters the sleep mode.
3. Click “OK” to renew the setting.
2. Set “Waiting Time” (Unit: minutes) to specify the amount of
time until the scanner enters the sleep mode.
3. Click “OK” to renew the setting.
15 minutes When returning back to the
Ready Mode from the Sleep
Mode, execute “Sleep
Mode” for Test (9.3.6) on the
main menu, and then click
“STOP” on the “Sleep
Mode” dialog box.
Mode, execute “Sleep
Mode” for Test (9.3.6) on the
main menu, and then click
“STOP” on the “Sleep
Mode” dialog box.
Clean Imprinter
1. Click “Clean Imprinter” on the main menu to clean the
imprinter’s print head.
imprinter’s print head.
—
This item is available only if
the optional Pre-imprinter is
installed to the scanner.
the optional Pre-imprinter is
installed to the scanner.
Buzzer Setting
1. Click “Buzzer Setting” on the main menu.
2. Set “Buzzer Setting (ON or OFF)” on the “Buzzer Setting”
dialog box.
3. Click “OK” to renew the setting.
2. Set “Buzzer Setting (ON or OFF)” on the “Buzzer Setting”
dialog box.
3. Click “OK” to renew the setting.
—
User Shading
1. Click “User Shading” on the main menu.
2. Click “Start Shading” or “Restore Default” on the “User
Shading” dialog box.
Note:
2. Click “Start Shading” or “Restore Default” on the “User
Shading” dialog box.
Note:
a. When selecting “Restore Default”, the factory-setting
data will be overwritten in stead of the current
shading data.
b. The following procedures from “3.” onwards are
available only for selecting “Start Shading”.
data will be overwritten in stead of the current
shading data.
b. The following procedures from “3.” onwards are
available only for selecting “Start Shading”.
3. Clean the conveyor, rollers, and ADF Glasses
according to the message on the display.
And click “OK”.
4. Switch Reference Plates to white according to the message
on the display.
And click “OK”.
5. Set the included Shading Paper or Shading Paper
(Part No.: See 14.7.) on the Hopper Tray in landscape
orientation.
6. And click “OK” to scan the Shading Paper.
7. Switch the Reference Plates to black according to the
message on the display. And click “OK”
8. Click “OK” to finish the shading correction.
9. Click “Close” to return to the main menu.
according to the message on the display.
And click “OK”.
4. Switch Reference Plates to white according to the message
on the display.
And click “OK”.
5. Set the included Shading Paper or Shading Paper
(Part No.: See 14.7.) on the Hopper Tray in landscape
orientation.
6. And click “OK” to scan the Shading Paper.
7. Switch the Reference Plates to black according to the
message on the display. And click “OK”
8. Click “OK” to finish the shading correction.
9. Click “Close” to return to the main menu.
—
1. Before executing the
shading function, be sure to
clean the ADF Glasses,
rollers, and conveyors
related to
shading function, be sure to
clean the ADF Glasses,
rollers, and conveyors
related to
conveying
documents
.
2. Until this process is
completed, don’t stop the
process by opening any
doors or turning off the
scanner.
completed, don’t stop the
process by opening any
doors or turning off the
scanner.
Caution Setting
1. Click “Caution Setting” on the main menu.
2. Change the parameter value on the “Caution Setting”
dialog box.
3. Click “OK” to renew the setting.
2. Change the parameter value on the “Caution Setting”
dialog box.
3. Click “OK” to renew the setting.
Clean:
20000
Replace:
300000
Set Default
1. Click “Set Default” on the main menu.
2. Click “Set Default” on the “Set Default” dialog box to set
the default values for “Sleep Mode”, “Caution Setting”,
and “Feed Speed”.
3. Click “Close” to return to the main menu.
2. Click “Set Default” on the “Set Default” dialog box to set
the default values for “Sleep Mode”, “Caution Setting”,
and “Feed Speed”.
3. Click “Close” to return to the main menu.
—
99
9.3.6.
Test
Item
Operation
Default
Remarks
LED
1. Click “LED” on the main menu.
2. Click “START” on “LED” dialog box to start LED Test
continuously until clicking “STOP”.
3. Click “Close” to return to the main menu.
2. Click “START” on “LED” dialog box to start LED Test
continuously until clicking “STOP”.
3. Click “Close” to return to the main menu.
—
The indicator turns on or off
in a constant period.
Green
in a constant period.
Green
→ Orange → Red
→ Green → Orange ......
Key / Sensor
1. Click “Key / Sensor” on the main menu.
2. Check the key and sensor status on the “Key / Sensor”
dialog box.
2. Check the key and sensor status on the “Key / Sensor”
dialog box.
3. Click “Close” to return to the main menu.
—
Size Detector 1 is for
detecting the Document
Guide located on the left
side as seen from the right of
the unit.
detecting the Document
Guide located on the left
side as seen from the right of
the unit.
Size Detector 2 is for
detecting the Document
Guide located on the right
side as seen from the right of
the unit.
detecting the Document
Guide located on the right
side as seen from the right of
the unit.
As the Document Guides are
slid to approach the front
panel, Size Detector 1
and Size Detector 2 will turn
OFF.
Conversely, as the
Document Guides are slid to
be away from the front panel,
Size Detector 1 and Size
Detector 2 will turn ON.
slid to approach the front
panel, Size Detector 1
and Size Detector 2 will turn
OFF.
Conversely, as the
Document Guides are slid to
be away from the front panel,
Size Detector 1 and Size
Detector 2 will turn ON.
Sensor Sensitive
Level
Level
1. Click “Sensor Sensitive Level” on the main menu.
2. Check each sensor’s sensitive level (Offset, Slice) on the
Sensor Sensitive Level dialog box.
3. Click “Close” to return to the main menu.
2. Check each sensor’s sensitive level (Offset, Slice) on the
Sensor Sensitive Level dialog box.
3. Click “Close” to return to the main menu.
—
Feed Motor
1. Click “Feed Motor” on the main menu.
2. Click “START” on the “Feed Motor” dialog box to start to
rotate the Paper Feed Motor continuously until clicking
“STOP”.
3. Click “Close” to return to the main menu.
2. Click “START” on the “Feed Motor” dialog box to start to
rotate the Paper Feed Motor continuously until clicking
“STOP”.
3. Click “Close” to return to the main menu.
—
Conveyor Motor
1. Click “Conveyor Motor” on the main menu.
2. Click “START” on the “Conveyor Motor” dialog box to start
to rotate the Conveyor Motor continuously until clicking
“STOP”.
3. Click “Close” to return to the main menu.
2. Click “START” on the “Conveyor Motor” dialog box to start
to rotate the Conveyor Motor continuously until clicking
“STOP”.
3. Click “Close” to return to the main menu.
—
Hopper Drive
1. Click “Hopper Drive” on the main menu.
2. Click “START” on the “Hopper Drive” dialog box to start
to execute the Hopper’s Up/Down movement continuously
until clicking “STOP”.
3. Click “Close” to return to the main menu.
2. Click “START” on the “Hopper Drive” dialog box to start
to execute the Hopper’s Up/Down movement continuously
until clicking “STOP”.
3. Click “Close” to return to the main menu.
—
100
Feed
1. Set documents on the Hopper Tray.
2. Click “Feed” on the main menu.
2. Click “Feed” on the main menu.
3. Set “Test Mode” and “Test Condition” depending on each
scanning condition.
Note:
scanning condition.
Note:
“Imprinter” is available only when the
optional Imprinter is installed.
optional Imprinter is installed.
4. Click “START” on the “Feed” dialog box to start feeding
documents.
Note:
When “Flatbed” on the “Test Mode” is selected, check
the CIS Carriage’s sliding from one end to the other
repeatedly is tested.
5. Click “STOP” on the “Feed” dialog box to stop the test.
6. Click “Close” to return to the main menu.
documents.
Note:
When “Flatbed” on the “Test Mode” is selected, check
the CIS Carriage’s sliding from one end to the other
repeatedly is tested.
5. Click “STOP” on the “Feed” dialog box to stop the test.
6. Click “Close” to return to the main menu.
—
Sleep Mode
1. Click “Sleep Mode” on the main menu.
2. Click “START” on the “Sleep Mode” dialog box to enter the
sleep mode.
3. Click “STOP” to return from the sleep mode.
4. Click “Close” to return to the main menu.
2. Click “START” on the “Sleep Mode” dialog box to enter the
sleep mode.
3. Click “STOP” to return from the sleep mode.
4. Click “Close” to return to the main menu.
—
CIS Level
1. Click “CIS Level” on the main menu.
2. Switch the Reference Plate (F) and Reference Plate (B) to
white.
3. Set “Gain” for the Front and Back sides on the “CIS Level”
dialog box.
4. Click “START” on the “CIS Level” dialog box to start
the CIS Level Test.
5. Check whether the peak level is within specifications.
(See Remarks.)
6. Click “STOP” to finish this test.
7. Click “Close” to return to the main menu.
2. Switch the Reference Plate (F) and Reference Plate (B) to
white.
3. Set “Gain” for the Front and Back sides on the “CIS Level”
dialog box.
4. Click “START” on the “CIS Level” dialog box to start
the CIS Level Test.
5. Check whether the peak level is within specifications.
(See Remarks.)
6. Click “STOP” to finish this test.
7. Click “Close” to return to the main menu.
—
Item
Operation
Default
Remarks
Click on the first or last page to see other KV-S7075C (serv.man2) service manuals if exist.