Panasonic WV-CS320 / WV-CS324E Service Manual ▷ View online
– 1-1 –
CONSTRUCTIONS
(WV-CS320)
(WV-CS324E)
Q
Y
U
I
R
T
W
E
∗
Q
Video Output Connector
W
Power Cable for WV-CS320
E
∗
Power Cable for WV-CS324E
R
Camera Mounting Base
T
Panning Starting Point
Y
Fall Prevention Wire
U
Decoration Cover
I
Dome Cover
– 2-1 –
LIST OF CONSUMPTION PARTS
MO1
Tilt Motor
REF. NO.
PART NAME
LIFE
MO2
Pan Motor
MO3
Cooling Fan
* This is working all the time.
Equal to power on time.
* Lens Motor itself is not supplied, but only
supplied as assembly.
M9
Lens (Focus Motor, Zoom Motor)
M13
Slip Ring
8
Those figures are just for a reference under 35 ˚C environmental temperature and not for a guarantee.
It changes depending on the actual environment/operating condition.
8
Part numbers of these consumption parts are described in Replacement Parts List on page 7-1.
2.16 million PRESET actions
2.16 million AUTOPAN revolutions
(19,200 hours as 32 sec per a turn)
2.16 million AUTOPAN revolutions
(19,200 hours as 32 sec per a turn)
50,000 hours
Each 3.7 million actions
10 million PRESET actions
10 million AUTOPAN revolutions
(88,888 hours as 32 sec per a turn)
10 million AUTOPAN revolutions
(88,888 hours as 32 sec per a turn)
1. Test Equipments Required
The following Test Equipments are required for adjustment
of the Colour CCTV Camera WV-CS320/WV-CS324E.
8
Underscanned Colour Video Monitor
8
Frequency Counter
8
Oscilloscope
8
Vectorscope
8
Lux Meter
8
Lighting (140 footcandles (1 400 lx), Colour Temperature
3 200 ˚K)
8
Logarithmic Gray Scale Chart (Part No. : YWV2310RB99).
8
Colour Chip Chart (Part No.: YWV2100RB98).
8
White Chart or White Paper
8
Radiation Chart
8
Colour Temperature Conversion Filters
Recommended manufacturer and part numbers are
shown in Table 1-1.
Table 1-1
8
Electric Variable Resistor (E.V.R.) kit (Part No. :
YWV0EA1174AN) as shown in Fig. 1-1.
Fig. 1-1
8
12 V DC Power Supply Unit
8
Personal Computer (IBM PC/AT type or equivalent)
8
Standard Straight RS-232C Cable
8
System Controller such as WV-CU151 or WV-CU161
8
Extension Cable A (Part No. : V0EA1409AN) between
CN201 of the Main Board and Lens as shown in Fig. 1-2
Fig. 1-2
– 2-2 –
ADJUSTMENT PROCEDURE
8
Extension Cable B (Part No. : K9ZZ00000963) between
CN204 of the Main Board and CN600 of the Servo Board
as shown in Fig. 1-3
Fig. 1-3
8
Extension Cable C (Part No. : V0EA1266AN) between the
Power Board and the AC Power Line as shown in Fig. 1-4
Fig. 1-4
8
CCD Mounting Adjustment Jig (Part No. : V0MA1120AN)
as shown in Fig. 1-5
Fig. 1-5
8
Lens Adaptor for CCD Mounting Adjustment (Part No. :
V0MA1207AN) as shown in Fig. 1-6
To
Power Board E5, E6
Power Board E5, E6
To
AC Power Line
AC Power Line
UP
A
B
C
UP
A
B
C
D
To
Main Board CN204
Main Board CN204
To
Servo Board CN600
Servo Board CN600
Conversion
KENKO KODAK
3 200 ˚K
B
5 100 ˚K
C12
80B
3 200 ˚K
B
6 500 ˚K
C4 and C12
80B and 80C
To
Lens
Lens
To
Main Board
CN201
Main Board
CN201
E
Referring to Fig. 2-1-3, disconnect the connector of the
Slip Ring.
Fig. 2-1-3
Note) When mounting the camera head on the power supply
unit, insert the projection of the power supply unit to
the notch of the Camera Mounting Plate as shown in
Fig. 2-1-4.
Fig. 2-1-4
R
Referring to Fig. 2-1-5, remove one screw that secures
the Inner Dome and remove the Inner Dome Cover.
Fig. 2-1-5
– 2-3 –
Fig. 1-6
2. Disassembling Procedure
2.1. Disassembling Procedure for Camera
Head
Q
Referring to Fig. 2-1-1, remove the Dome Cover while
turning it to counterclockwise direction.
Fig. 2-1-1
W
Referring to Fig. 2-1-2, remove four screws that secure
the Main Chassis and remove the Main Chassis.
Fig. 2-1-2
Dome
Cover
Cover
Remove
four screws.
four screws.
Main
Chassis
Chassis
Disconnect.
Power
Supply
Chassis
Supply
Chassis
Projection
Notch
Camera
Mounting
Plate
Mounting
Plate
Remove
one screw.
one screw.
Inner Dome Cover
Click on the first or last page to see other WV-CS320 / WV-CS324E service manuals if exist.