DOWNLOAD Panasonic SA-BFT800EE / SA-BFT800EEK Service Manual ↓ Size: 15.52 MB | Pages: 127 in PDF or view online for FREE

109

Step 3 Remove 1 screw from the Regulator Diode (D5803).
Step 4 Remove the Heatsink Unit A together with Regulator
Diode (D5802).
Step 5 Remove 1 screw from the Regulator Diode (D5802).
Step 6 Remove the Regulator Diode (D5802) from the Heatsink
Unit B.
Caution: Avoid touching the Heatsink Unit A due to its high 
temperature after prolonged use. Touching it may lead to 
injuries.
Note: Refer to the diagrams of SMPS P.C.B. (Item 18.4) for
location of the electrical components.

Step 1 Apply grease to the Heatsink Unit A.
Step 2 Fix and screw the Regulator Diode (D5802) to the Heat-

sink Unit A.
Caution: Ensure the Regulator Diode (D5802) is tightly 
screwed to the Heatsink Unit A.
Step 3 Fix the Heatsink Unit B with Regulator Diode (D5802)
onto SMPS P.C.B..
Caution: Ensure the Heatsink Unit A with Regulator Diode 
(D5802) are properly seated on SMPS P.C.B..
Step 4 Fix and screw the Regulator Diode (D5803) to the Heat-
sink Unit A.

Step 5 Solder pins of the Rectifier Diode (D5802) on the solder
side of SMPS P.C.B..
Step 6 Solder pins of the Heatsink Unit A on the solder side of
SMPS P.C.B..
Caution: Ensure pins of the Regulator Diode (D5802) are 
properly seated before soldered onto SMPS P.C.B..

110

• Refer to “Disassembly of Back Cabinet Assembly”.
• Refer to “Disassembly of SMPS Shield Unit”.
• Refer to “Disassembly of Digital Shield”.
• Refer to “Disassembly of Power P.C.B.”.
• Refer to “Disassembly of SMPS P.C.B.”.

Step 1 Desolder pins of the Regulator Diode (D5803) on the
solder side of SMPS P.C.B..
Step 2 Desolder pins of the Heatsink Unit A.

Step 3 Remove 1 screw from the Regulator Diode (D5802).
Step 4 Remove the Heatsink Unit A together with Regulator
Diode (D5803).
Step 5 Remove 1 screw from the Regulator Diode (D5803).
Step 6 Remove the Regulator Diode (D5803) from the Heatsink
Unit B.
Caution: Avoid touching the Heatsink Unit A due to its high 
temperature after prolonged use. Touching it may lead to 
injuries.
Note: Refer to the diagrams of SMPS P.C.B. (Item 18.4) for
location of the electrical components.

Step 1 Apply grease to the Heatsink Unit A.
Step 2 Fix and screw the Regulator Diode (D5803) to the Heat-
sink Unit A.
Caution: Ensure the Regulator Diode (D5803) is tightly 
screwed to the Heatsink Unit A.
Step 3 Fix the Heatsink Unit A with Regulator Diode (D5803)
onto SMPS P.C.B..
Caution: Ensure the Heatsink Unit A with Regulator Diode 
(D5802) are properly seated on SMPS P.C.B..
Step 4 Fix and screw the Regulator Diode (D5802) to the Heat-
sink Unit A.

Step 5 Solder pins of the Regulator Diode (D5803) on the sol-
der side of SMPS P.C.B..
Step 6 Solder pins of the Heatsink Unit A on the solder side of
SMPS P.C.B..

111

Step 1  Remove 1 screw.

Step 1  Press the push lever to release it.

Step 2  Release catch to remove push lever.
Caution: Apply gentle force during disassembling.

Step 3  Peel off Himelon N & Gasket F.
Caution: Replace Himelon N & Gasket if torn.
Step 4  Detach 15P FFC at the connector (CN1002) on iPod
P.C.B..

112

Step 5  Remove 3 screws.

Step 6  Remove iPod Spring Plate.
Caution: Keep the iPod Spring Plate in safe place, place it 
back during assembling.
Step 7  Remove 1 screw.
Step 8  Remove iPod Switch P.C.B..

Step 9  Press and hold the docking holder with gentle force as
arrow shown.

Step 10  Remove the docking holder.