JBL PULSE (serv.man6) EMC - CB Certificate ▷ View online
Page 9 of 51
Report No. 241619
TRF No. IEC60950_1C
Test item particulars
................................................... :
Equipment mobility..................................................... : [] movable [] hand-held [X] transportable
[] stationary [] for building-in [] direct plug-in
Connection to the mains ............................................ : [] pluggable equipment [] type A [] type B
[] permanent connection
[] detachable power supply cord
[] non-detachable power supply cord
[X] not directly connected to the mains
[] detachable power supply cord
[] non-detachable power supply cord
[X] not directly connected to the mains
Operating condition .................................................... : [X] continuous
[] rated operating / resting time:
Access location ......................................................... : [X] operator accessible
[] restricted access location
Over voltage category (OVC) ................................... : [X] OVC I [] OVC II [] OVC III [] OVC IV
[] other:
Mains supply tolerance (%) or absolute mains
supply values ............................................................ : N/A
Tested for IT power systems .................................... : N/A
IT testing, phase-phase voltage (V) .......................... : N/A
Class of equipment ................................................... : [] Class I [] Class II [X] Class III
supply values ............................................................ : N/A
Tested for IT power systems .................................... : N/A
IT testing, phase-phase voltage (V) .......................... : N/A
Class of equipment ................................................... : [] Class I [] Class II [X] Class III
[] Not classified
Considered current rating of protective device as
part of the building installation (A) ............................ : 16A (20A for Canada and US)
Pollution degree (PD) ............................................... : [] PD 1 [X] PD 2 [] PD 3
IP protection class .................................................... : IPX0
Altitude during operation (m) .................................... : Up to 2000m:
Altitude of test laboratory (m) .................................... : Up to 2000m:
Mass of equipment (kg) ............................................ : Weight Approx.: 520g
part of the building installation (A) ............................ : 16A (20A for Canada and US)
Pollution degree (PD) ............................................... : [] PD 1 [X] PD 2 [] PD 3
IP protection class .................................................... : IPX0
Altitude during operation (m) .................................... : Up to 2000m:
Altitude of test laboratory (m) .................................... : Up to 2000m:
Mass of equipment (kg) ............................................ : Weight Approx.: 520g
Dimension (Diameter x High): 79mm x 182mm
Possible test case verdicts:
- test case does not apply to the test object ................. : N/A
- test object does meet the requirement....................... : P (Pass)
- test object does not meet the requirement ................ : F (Fail)
Testing
.......................................................................... :
Date of receipt of test item ............................................ : August 2013
Date(s) of performance of tests .................................... : August 2013
Page 10 of 51
Report No. 241619
TRF No. IEC60950_1C
General remarks:
”This report is not valid as a CB Test Report unless appended by an approved CB Testing
Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with
IECEE 02”.
Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with
IECEE 02”.
The test result presented in this report relate only to the object(s) tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
”(see attachment #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
Manufacturer’s Declaration per sub-clause 6.2.5 of IECEE 02:
The application for obtaining a CB Test Certificate
includes more than one factory location and a
declaration from the Manufacturer stating that the
sample(s) submitted for evaluation is (are)
representative of the products from each factory has
been provided ................................................................:
includes more than one factory location and a
declaration from the Manufacturer stating that the
sample(s) submitted for evaluation is (are)
representative of the products from each factory has
been provided ................................................................:
Yes
Not applicable
When differences exist; they shall be identified in the General product information section.
Name and address of factory (ies) .......................... :
Dong Guan Tai Sing Audio Technology Ltd
Tai Sing Industrial Road, Bai Zhou Bian Village,
Dong Cheng, Dongguan City, Guangdong
Tai Sing Industrial Road, Bai Zhou Bian Village,
Dong Cheng, Dongguan City, Guangdong
Page 11 of 51
Report No. 241619
TRF No. IEC60950_1C
General product information:
The EUT is a Class III portable wireless speaker with rechargeable battery and light effects. The unit will
be connected to a certified power adapter, refer to list of critical components on table 1.5.1. Internal
enclosure is plastic material of V-0 grade and totally enclosed with screws. The top and bottom ring
covers are enclosed to internal enclosure with screws.
I/O ports: one Aux-in jack and one USB port used for charging battery pack within EUTonly
Load condition:
The EUT is a Class III portable wireless speaker with rechargeable battery and light effects. The unit will
be connected to a certified power adapter, refer to list of critical components on table 1.5.1. Internal
enclosure is plastic material of V-0 grade and totally enclosed with screws. The top and bottom ring
covers are enclosed to internal enclosure with screws.
I/O ports: one Aux-in jack and one USB port used for charging battery pack within EUTonly
Load condition:
By using 1kHz sine wave input through to measuring Max. and 1/8 Max. non-clipped level.
Normal operation with 1/8 non-clipped output power on speaker with 1kHz sine wave, LED module is
normal operated.
Normal operation with 1/8 non-clipped output power on speaker with 1kHz sine wave, LED module is
normal operated.
If not specified, Aux-in mode
used for test and the data in the report represent the worst case.
Maximum recommended ambient (Tmra): 35°C
Circuit characteristics: Secondary (SELV) circuit.
1.1.2 - Additional requirements:
1.1.2 - Additional requirements:
Exposure to extreme temperatures, excessive dust, moisture or vibration; to flammable gases; to
corrosive or explosive atmospheres:
This equipment is intended to operate in a "normal" environment (Offices and homes).
Electromedical equipment connected to the patient:
This equipment is not an electromedical equipment intended to be physically connected to a patient.
Equipment used in vehicles, ships or aircrafts, in tropical countries, or at elevations > 2000m:
This equipment is intended to operate in a "normal" environment (Offices and homes).
corrosive or explosive atmospheres:
This equipment is intended to operate in a "normal" environment (Offices and homes).
Electromedical equipment connected to the patient:
This equipment is not an electromedical equipment intended to be physically connected to a patient.
Equipment used in vehicles, ships or aircrafts, in tropical countries, or at elevations > 2000m:
This equipment is intended to operate in a "normal" environment (Offices and homes).
Abbreviations used in the report:
-
normal
conditions
N.C.
- single fault conditions
S.F.C
-
functional
insulation OP
-
basic
insulation
BI
-
double
insulation
DI
-
supplementary
insulation
SI
- between parts of opposite
polarity
BOP
-
reinforced
insulation
RI
Indicate used abbreviations (if any)
Page 12 of 51
Report No. 241619
IEC
60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1C
1 GENERAL
—
1.5 Components
P
1.5.1
General
Refer to below.
P
Comply with IEC 60950-1 or relevant component
standard
standard
(see appended tables 1.5.1)
P
1.5.2
Evaluation and testing of components
Certified components are
used in accordance with their
ratings, certifications and they
comply with applicable parts
of this standard.
Components not certified are
used in accordance with their
ratings and they comply with
applicable parts of
IEC 60950-1 and the relevant
component standard.
Components, for which no
relevant IEC-standard exists,
have been tested under the
conditions occurring in the
equipment, using applicable
parts of IEC 60950-1.
used in accordance with their
ratings, certifications and they
comply with applicable parts
of this standard.
Components not certified are
used in accordance with their
ratings and they comply with
applicable parts of
IEC 60950-1 and the relevant
component standard.
Components, for which no
relevant IEC-standard exists,
have been tested under the
conditions occurring in the
equipment, using applicable
parts of IEC 60950-1.
P
1.5.3
Thermal controls
No thermal controls.
N/A
1.5.4
Transformers
No transformer used.
N/A
1.5.5
Interconnecting cables
The interconnecting cables
contain only SELV.
contain only SELV.
P
1.5.6
Capacitors bridging insulation
No primary circuits.
N/A
1.5.7
Resistors bridging insulation
No such resistor used.
N/A
1.5.7.1
Resistors bridging functional, basic or
supplementary insulation
supplementary insulation
N/A
1.5.7.2
Resistors bridging double or reinforced insulation
between a.c. mains and other circuits
between a.c. mains and other circuits
No resistors bridging double
or reinforced insulation
between a.c mains and other
circuits.
or reinforced insulation
between a.c mains and other
circuits.
N/A
1.5.7.3
Resistors bridging double or reinforced insulation
between a.c. mains and antenna or coaxial cable
between a.c. mains and antenna or coaxial cable
No resistors bridging double
or reinforced insulation
between a.c mains and
antenna or coaxial cable.
or reinforced insulation
between a.c mains and
antenna or coaxial cable.
N/A
1.5.8
Components in equipment for IT power systems
The equipment is regarded as
class III.
class III.
N/A
Click on the first or last page to see other PULSE (serv.man6) service manuals if exist.