JBL ON BEAT MICRO (serv.man3) EMC - CB Certificate ▷ View online
Issue Date:
2012-10-23
Page 45 of 50
Report Reference #
E204594-A37-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
supplementary information:
Complies with 5.3.4 c.
2.10.5
TABLE: distance through insulation measurements
N/A
Distance through insulation (DTI) at/of:
U peak
(V)
Urms
(V)
Test
voltage
(V)
Required DTI
(mm)
DTI
(mm)
supplementary information:
4.3.8
TABLE: Batteries
N/A
The tests of 4.3.8 are applicable only when appropriate
battery data is not available.
battery data is not available.
Is it possible to install the battery in a reverse polarity
position?
position?
-
Non-rechargeable batteries
Rechargeable batteries
Discharging
Un-
intentional
charging
Charging
Discharging
Reversed
charging
Meas.
current
current
Manuf.
specs.
specs.
Meas. current
Manuf.
specs.
specs.
Meas.
current
current
Manuf.
specs.
specs.
Meas.
current
current
Manuf.
specs.
specs.
Max.
current
during
normal
operation
current
during
normal
operation
-
-
-
-
-
-
-
-
-
Max.
current
during fault
operation
current
during fault
operation
-
-
-
Issue Date:
2012-10-23
Page 46 of 50
Report Reference #
E204594-A37-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
Test results:
Verdict
- Chemical leaks
- Explosion of the battery
- Emission of flame or expulsion of molten metal
- Electric strength tests of equipment after completion of tests
supplementary information:
Optional, not provided with unit. Consumer grade, non-rechargeable carbon-zinc or alkaline batteries are
considered safe under short-circuiting conditions and therefore are not tested for discharge; nor are such
considered safe under short-circuiting conditions and therefore are not tested for discharge; nor are such
batteries tested for leakage under storage conditions.
4.3.8
TABLE: Batteries
N/A
Battery Category (Lithium, NiMh,
NiCad, Lithium ion,
etc.).......................................................:
NiCad, Lithium ion,
etc.).......................................................:
Manufacturer.........................................:
Type/Model...........................................:
Voltage.................................................:
Capacity (mAh)....................................:
Tested and Certified by (incl. Ref.
No.).......................................................:
No.).......................................................:
Circuit protection diagram (Refer
indicated supplement of Enclosure-
Miscellaneous)......................................:
indicated supplement of Enclosure-
Miscellaneous)......................................:
Issue Date:
2012-10-23
Page 47 of 50
Report Reference #
E204594-A37-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
MARKINGS AND INSTRUCTIONS (1.7.12, 1.7.15)
Location of replaceable battery.....:
Language(s)..........................................:
Close to the
battery..................................................:
battery..................................................:
In the servicing
instructions...........................................:
instructions...........................................:
In the operating
instructions...........................................:
instructions...........................................:
In the operating instructions
supplementary information:
Additional devices may be described in Enclosure - Miscellaneous
4.5 TABLE: Thermal requirements
Pass
Supply voltage (V) ........................................... :
6 Vdc
-
--
--
--
—
Ambient Tmin (°C ) ......................................... :
See
Below
Below
-
--
--
--
—
Ambient Tmax (°C ) ........................................ :
See
Below
Below
-
--
--
--
—
Maximum measured temperature T of part/at:
T (°C)
allowed
Tmax
(°C)
PWB adjacent to U301
90.4
-
--
--
--
105
PWB adjacent to U302
80.4
-
--
--
--
105
PWB adjacent to U303
98.9
-
--
--
--
105
PWB adjacent to D304
93.3
-
--
--
--
105
PWB adjacent to L302
46.4
-
--
--
--
105
Enclosure Hot spot Top
42.4
-
-
-
-
95
Enclosure Hot spot Bottom
38.3
-
-
-
-
95
Ambient
24.7
-
-
-
-
-
temperature T of winding:
t
1
(°C) R
1
(
) t
2
(°C) R
2
(
)
T (°C) allowed
T
max
(°C)
insulation
class
-
-
-
-
-
-
-
-
supplementary information:
Tma=25°C. Maximum Normal Load: Unit on and USB and IPhone 5 ports loaded to their maximum. USB =
1.24A; IPhone 5 = 1.24A
1.24A; IPhone 5 = 1.24A
Issue Date:
2012-10-23
Page 48 of 50
Report Reference #
E204594-A37-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
4.5.5
TABLE: Ball pressure test of thermoplastic parts
N/A
allowed impression diameter (mm) ........................ : less than or equal to 2.0
—
part
test temperature ( °C) impression diameter
(mm)
supplementary information:
4.7
TABLE: resistance to fire
Pass
part
manufacturer of
material
type of material
thickness
(mm)
flammability
class
Evidence
supplementary information:
See appended Critical Components Table.
5.1
TABLE: touch current measurement
N/A
Measured between:
Measured
(mA)
Limit
(mA)
Comments/Conditions
supplementary information:
5.2
TABLE: electric strength tests, impulse tests and voltage surge tests
N/A
Test voltage applied between:
Voltage shape
(AC, DC,
impulse, surge)
Test voltage
(V)
Breakdown
Yes / No
Functional:
Test voltage applied between:
Voltage shape
(AC, DC,
impulse, surge)
Test voltage
(V)
Breakdown
Yes / No
Click on the first or last page to see other ON BEAT MICRO (serv.man3) service manuals if exist.