JBL FLIP II (serv.man6) EMC - CB Certificate ▷ View online
Page 11 of 88 Report No. EFSN13070129E-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1C
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
Supplied by approved adapter
which provides SELV output
only, and no hazards live part
in operator access areas.
which provides SELV output
only, and no hazards live part
in operator access areas.
P
2.1.1.1
Access to energized parts
N/A
Test by inspection ................................................. :
N/A
Test with test finger (Figure 2A) ............................ :
N/A
Test with test pin (Figure 2B) ................................ :
N/A
Test with test probe (Figure 2C) ........................... : No TNV circuits within the
equipment.
N/A
2.1.1.2
Battery compartments
TNV circuits within the
equipment
equipment
N/A
2.1.1.3
Access to ELV wiring
No internal wiring at ELV
accessible to the operator.
accessible to the operator.
N/A
Working voltage (Vpeak or Vrms); minimum
distance through insulation (mm)
distance through insulation (mm)
2.1.1.4
Access to hazardous voltage circuit wiring
No internal wiring at ELV
accessible to the operator.
accessible to the operator.
N/A
2.1.1.5
Energy hazards ..................................................... :
N/A
2.1.1.6
Manual controls
No conductive shafts of
operating knobs, handles,
levers and the like
operating knobs, handles,
levers and the like
N/A
2.1.1.7
Discharge of capacitors in equipment
N/A
Measured voltage (V); time-constant (s) ................ :
2.1.1.8
Energy hazards
– d.c. mains supply
Not connected to DC mains
supply.
supply.
N/A
a) Capacitor connected to the d.c. mains supply .. :
N/A
N/A
2.1.1.9
Audio amplifiers ..................................................... :
P
2.1.2
Protection in service access areas
No bare parts operating at
hazardous voltage in a
service access area
hazardous voltage in a
service access area
N/A
2.1.3
Protection in restricted access locations
The equipment is not limited
to be used in restricted
access locations.
to be used in restricted
access locations.
N/A
2.2
SELV circuits
P
2.2.1
General requirements
P
2.2.2
Voltages under normal conditions (V) ................... : Between any conductor of the
SELV circuits, 42.4Vpeak or
60Vd.c. is not exceeded.
60Vd.c. is not exceeded.
P
Page 12 of 88 Report No. EFSN13070129E-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1C
2.2.3
Voltages under fault conditions (V) ....................... : Under fault conditions
voltages never exceed 71Vpk
and 120Vdc and do not
exceed 42.4Vpk or 60Vdc for
more than 0.2 second
and 120Vdc and do not
exceed 42.4Vpk or 60Vdc for
more than 0.2 second
P
2.2.4
Connection of SELV circuits to other circuits ...... :
SELV circuits are only
connected to other secondary
circuits. SELV circuit and all
interconnected circuits
separated from primary by
double/reinforced insulation
connected to other secondary
circuits. SELV circuit and all
interconnected circuits
separated from primary by
double/reinforced insulation
P
2.3
TNV circuits
N/A
2.3.1
Limits
No TNV circuits within the
equipment.
equipment.
N/A
Type of TNV circuits ............................................... :
2.3.2
Separation from other circuits and from accessible
parts
parts
N/A
2.3.2.1
General requirements
N/A
2.3.2.2
Protection by basic insulation
N/A
2.3.2.3
Protection by earthing
N/A
2.3.2.4
Protection by other constructions ......................... :
N/A
2.3.3
Separation from hazardous voltages
N/A
Insulation employed ............................................... :
2.3.4
Connection of TNV circuits to other circuits
N/A
Insulation employed ............................................... :
2.3.5
Test for operating voltages generated externally
N/A
2.4
Limited current circuits
N/A
2.4.1
General requirements
N/A
2.4.2
Limit values
N/A
Frequency (Hz) ...................................................... :
Measured current (mA) .......................................... :
Measured voltage (V) ............................................. :
Measured circuit capacitance (nF or µF) ............... :
2.4.3
Connection of limited current circuits to other
circuits
circuits
N/A
2.5
Limited power sources
Evaluated in approved adapter
N/A
Page 13 of 88 Report No. EFSN13070129E-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1C
a) Inherently limited output
N/A
b) Impedance limited output
N/A
c) Regulating network limited output under normal
operating and single fault condition
operating and single fault condition
N/A
d) Overcurrent protective device limited output
N/A
Max. output voltage (V), max. output current (A),
max. apparent power (VA) ..................................... :
max. apparent power (VA) ..................................... :
Current rating of overcurrent protective device (A) .:
Use of integrated circuit (IC) current limiters
2.6
Provisions for earthing and bonding
N/A
2.6.1
Protective earthing
N/A
2.6.2
Functional earthing
N/A
2.6.3
Protective earthing and protective bonding
conductors
conductors
N/A
2.6.3.1
General
N/A
2.6.3.2
Size of protective earthing conductors
N/A
Rated current (A), cross-sectional area (mm
2
),
AWG ....................................................................... :
2.6.3.3
Size of protective bonding conductors
N/A
Rated current (A), cross-sectional area (mm
2
),
AWG ....................................................................... :
Protective current rating (A), cross-sectional area
(mm
(mm
2
), AWG ........................................................... :
2.6.3.4
Resistance of earthing conductors and their
terminations; resistance (
terminations; resistance (
), voltage drop (V), test
current (A), duration (min) ...................................... :
N/A
2.6.3.5
Colour of insulation ................................................ :
N/A
2.6.4
Terminals
N/A
2.6.4.1
General
N/A
2.6.4.2
Protective earthing and bonding terminals
N/A
Rated current (A), type, nominal thread diameter
(mm) ....................................................................... :
(mm) ....................................................................... :
2.6.4.3
Separation of the protective earthing conductor
from protective bonding conductors
from protective bonding conductors
N/A
2.6.5
Integrity of protective earthing
N/A
2.6.5.1
Interconnection of equipment
N/A
2.6.5.2
Components in protective earthing conductors and
protective bonding conductors
protective bonding conductors
N/A
2.6.5.3
Disconnection of protective earth
N/A
Page 14 of 88 Report No. EFSN13070129E-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1C
2.6.5.4
Parts that can be removed by an operator
N/A
2.6.5.5
Parts removed during servicing
N/A
2.6.5.6
Corrosion resistance
N/A
2.6.5.7
Screws for protective bonding
N/A
2.6.5.8
Reliance on telecommunication network or cable
distribution system
distribution system
N/A
2.7
Overcurrent and earth fault protection in primary circuits
N/A
2.7.1
Basic requirements
N/A
Instructions when protection relies on building
installation
installation
N/A
2.7.2
Faults not simulated in 5.3.7
—
2.7.3
Short-circuit backup protection
N/A
2.7.4
Number and location of protective devices ........... :
N/A
2.7.5
Protection by several devices
N/A
2.7.6
Warning to service personnel ................................ :
N/A
2.8
Safety interlocks
N/A
2.8.1
General principles
No safety interlocks or similar
devices within the equipment
devices within the equipment
N/A
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
Protection against extreme hazard
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches, relays and their related circuits
N/A
2.8.7.1
Separation distances for contact gaps and their
related circuits (mm) ............................................. :
related circuits (mm) ............................................. :
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
2.9
Electrical insulation
P
Click on the first or last page to see other FLIP II (serv.man6) service manuals if exist.