DOWNLOAD JBL ES 150PW (serv.man5) Service Manual ↓ Size: 6.22 MB | Pages: 84 in PDF or view online for FREE

 

Page 10 of 58 

Report No.: 1009950 

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

8.22 

Non-separable thin sheet material  

 

N/A 

 

9.1 

Testing on the outside 

P 

9.1.1 

For voltages >1000 V ac or >1500 V dc complies 
with clause 13.3.1 for basic insulation  

 P 

9.1.1.1 

a) Open circuit voltages  

 

P 

 

b) Touch current measured from terminal devices 
using the network in 
annex D …………………………: 

Voltage U1: 0.056V pk 
Voltage U2: 0.056V pk 
Alternatively – Measured 
Current 

P 

 

c) Discharge not exceeding 45 μC  

 

N/A 

 

d) Energy of discharge not exceeding 350 mJ  

 

N/A 

9.1.1.2 

Test with test finger and test probe  

 

P 

9.1.2 

No hazardous live shafts of knobs, handles or levers   

P 

9.1.3 

Ventilation holes and other holes tested by means of 
4 mm x 100 mm test pin  

 N/A 

9.1.4 

Terminal devices tested with 1 mm x 20 mm test pin 
(10 N); test probe D of IEC 61032  

 P 

 

Terminal devices tested with 1 mm x 100 mm 
straight wire (1 N); test probe D of IEC 61032  

 P 

9.1.5 

Pre-set controls tested with 2.5 mm x 100 mm test 
pin (10 N); test probe C of IEC 61032  

 N/A 

9.1.6 

No shock hazard due to stored charge on withdrawal 
of the mains plug; voltage (V) after 2 s ………………:

0V<2s P 

 

If C is not greater than 0,1 μF no test needed  

 

N/A 

9.1.7 

Resistance to external forces 

 

P 

 

a) Test probe 11 of IEC 61032 for 10 s (50 N)  

 

P 

 

b) Test hook of fig. 4 for 10 s (20 N)  

 

P 

 

c) 30 mm diameter test tool for 5 s (100 or 250 N)  

250N 

P 

9.2 

No hazard after removing a cover by hand  

 

N/A 

 

10.1 

Insulation resistance (MΩ) at least 2 MΩ min. after 
surge test for basic and 4 MΩ min. for reinforced 
insulation .................................................................: 

 N/A 

10.2 

Humidity treatment 48 h or 120 h ...........................: 

48 h and 120 h 

P 

10.3 

Insulation resistance and dielectric strength between 
mains terminals  

(see appended table) 

P 

 

Page 11 of 58 

Report No.: 1009950 

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

 

Insulation Resistance and dielectric strength across 
BASIC or SUPPLEMENTARY insulation (Class 1)  

 P 

 

Insulation resistance and dielectric strength across 
REINFORCED insulation (Class II)  

 P 

 

11.1 

No shock hazard under fault condition  

 

P 

11.2 

Heating under fault condition  

 

P 

 

Flames extinguish within 10 seconds  

 

P 

 

No hazard from softening solder  

 

P 

 

Soldered terminations not used  as protective 
mechanism  

 P 

11.2.1 

Measurement of temperature rises  

(see appended table) 

P 

11.2.2 

Temperature rise of accessible parts  

(see appended table) 

P 

11.2.3 

Temperature rise of parts, other than windings, 
providing electrical insulation  

(see appended table) 

P 

 

Temperature rise of printed circuit boards (PCB) 
exceeding the limits of table 3 by max. 100 K for 
max. 5 min  

 N/A 

 

a) Temperature rise of printed circuit boards (PCB) 
to 20.1.3, exceeding the limits of table 3 by not more 
than 100 K for an area not greater than 2 cm² 
………: 

 N/A 

 

b) Temperature rise of printed circuit boards (PCB) 
to 20.1.3 up to 300 K for an area not greater than 
2 cm² for a maximum of 5 min  

 N/A 

 

Meets all the special conditions if conductors on 
printed circuit boards are interrupted  

 N/A 

 

Class I protective earthing maintained  

 

N/A 

11.2.4 

Temperature rise of parts acting as a support or  
mechanical barrier  

 P 

11.2.5 

Temperature rise of windings  

(see appended table) 

P 

11.2.6 

Temperature rise of parts not subject to the limits of 
11.2.1 to 11.2.5  

(see appended table) 

P 

 

12.1.1 

Bump test where mass >7 kg  

15.5kg 

P 

12.1.2 

Vibration test  

No connection or part that might 
impair safety can become loose 

P 

12.1.3 

Impact hammer test  

 

P 

 

Page 12 of 58 

Report No.: 1009950 

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

 

Steel ball test  

 

P 

12.1.4 

Drop test for portable apparatus where mass ≤ 7 kg    

N/A 

12.1.5 

Thermoplastic enclosures stress relief test  

 

P 

12.2 

Fixing of knobs, push buttons, keys and levers  

 

P 

12.3 

Remote controls with hazardous live parts  

 

N/A 

12.4 

Drawers (pull test 50 N, 10 s)  

 

N/A 

12.5 

Antenna coaxial sockets providing isolation  

 

N/A 

12.6 

Telescoping or rod antennas construction  

ES150PW/230:  
Antenna ball end Ø=7.5mm 

P 

12.6.1 

Telescoping or rod antennas securement  

20N 

P 

 

13.1 

Clearances in accordance with 13.3  

 

P 

 

Creepage distances in accordance with 13.4  

 

P 

13.2 

Determination of operating voltage  

 

P 

13.3 Clearances 

 

 

P 

13.3.1 General 

 

 

P 

13.3.2 

Circuits conductively connected to the mains comply 
with table 8 and, where applicable, table 9  ............: 

 P 

13.3.3 

Circuits not conductively connected to the mains 
comply with table 10  

Circuits not conductively 
connected to the mains cannot 
cause any shock hazard 

N/A 

13.3.4 

Measurement of transient voltages  

 

N/A 

13.4 

Creepage distances  

 

P 

 

Creepage distances greater than table 11 minimum 
values  

 P 

13.5 

Printed boards  

 

P 

13.5.1 

Clearances and creepage distances between 
conductors on printed circuit boards, one of which 
may be conductively connected to the mains, as in 
fig. 10  

 N/A 

13.5.2 

Type B coated printed circuit boards complying with 
IEC 60664-3 (basic insulation only)  

 N/A 

13.6 

Conductive parts along uncemented joints 
clearances and creepage distances comply with 13.3 
and 13.4  

 N/A 

 

Conductive parts along reliably cemented joints 
comply with 8.8  

 N/A 

 

Temperature cycle test and dielectric strength test  

 

N/A 

 

Page 13 of 58 

Report No.: 1009950 

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

13.7 

Enclosed, enveloped or hermetically sealed parts not 
conductively connected to the mains, clearances and 
creepage distances as in table 12  

 N/A 

13.8 

Parts filled with insulating compound, meeting the 
requirements of 8.8  

 N/A 

 

14.1 Resistors 

 

 

N/A 

 

a) Resistors between hazardous live parts and 
accessible metal parts  

 N/A 

 

b) Resistors, other than between hazardous live 
parts and accessible parts  

 N/A 

 

Resistors separately approved ……………………….:  

N/A 

14.2 

Capacitors and RC units  

 

P 

 

Capacitors separately approved ……………………:  Yes 

P 

14.2.1 

Y capacitors tested to IEC 60384-14, 2

nd

 edition ...: 

Y1: C03 

P 

14.2.2 

X capacitors tested to IEC 60384-14, 2

nd

 edition ...: 

X2: C19, C06 

P 

14.2.3 

Capacitors operating at mains frequency but not 
connected to the mains: tests for X2 ......................: 

 N/A 

14.2.5 

Capacitors with volume exceeding 1750 mm³, where 
short-circuit current exceeds 0,2 A: compliance with 
IEC60384-1, 4.38 category B or better  ..................: 

 N/A 

 

Capacitors with volume exceeding 1750 mm³, 
mounted closer to a potential ignition source than 
table 5 permits: compliance with IEC 60 384-1, 4.38 
category B or better  ................................................: 

 N/A 

 

Shielded by a barrier acc. to 20.1.4/ table 21 or 
metal ........................................................................: 

 N/A 

14.3 

Inductors and windings  

 

P 

 

Comply with IEC 61558-1, IEC 61558-2 
(as relevant) and clause 20.1.4  

 P 

14.3.1 

Transformers and inductors marked with 
manufacturer's name and type ...............................: 

Transtec 

TT0900901830-E 

Huizhou GP Wiring Technology

 

TD-230-0300A+C 
TD-230-0300A+A 

Standby transformer TR1: 
 DW KB1157-11486 

P 

 

Transformers and inductors separately approved .: 

No 

N/A 

14.3.2 General 

 

 

P 

 

Insulation material complies with clause 20.1.4  

 

P