Harman Kardon HS 2X0 EMC - CB Certificate ▷ View online
Page 55 of 62 Report No. SH10011244-001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
APPENDIX National differences United Kingdom
(These differences are taken from IEC 60065(2001) + Amendment 1 (2005).)
15.1.1 Apparatus which is fitted with a flexible cable
or cord and is designed to be connected to a mains
socket conforming to BS 1363 by means of that
flexible cable or cord and plug shall be fitted with
a ”standard plug” in accordance with Statutory
Instrument 1768: 1994: The Plugs and Sockets etc.
(Safety) Regulations 1994, unless exempted by
those Regulations.
NOTE ”Standard plug” is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved conversion
plug.
Justification:
SI 1768: 1994
or cord and is designed to be connected to a mains
socket conforming to BS 1363 by means of that
flexible cable or cord and plug shall be fitted with
a ”standard plug” in accordance with Statutory
Instrument 1768: 1994: The Plugs and Sockets etc.
(Safety) Regulations 1994, unless exempted by
those Regulations.
NOTE ”Standard plug” is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved conversion
plug.
Justification:
SI 1768: 1994
Pass
APPENDIX National differences for CHINA
(These differences are taken from IEC60065:1998 and adopted to IEC
60065:2001.)
60065:2001.)
4.2.1 first sentence replaced by:
The apparatus is connected to a supply voltage of
0.9 times or 1.1 times of any RATED SUPPLY
VOLTAGE for which the apparatus is designed.
The apparatus is connected to a supply voltage of
0.9 times or 1.1 times of any RATED SUPPLY
VOLTAGE for which the apparatus is designed.
Pass
5.1f） Second paragraph replaced by:
………When single rated voltage is given, it should
be marked 220 V, For a rating range, it should
cover 220 V; when multiple RATED
VOLTAGES are given, one of them must be 220V
and also factory default setting should be 220 V.
………When single rated voltage is given, it should
be marked 220 V, For a rating range, it should
cover 220 V; when multiple RATED
VOLTAGES are given, one of them must be 220V
and also factory default setting should be 220 V.
Pass
5.4 replaced by：
When information with regard to safety is required
according to this standard, this information shall be
given in an instruction for installation or use and
supplied with the apparatus. This information shall
be given in simplify Chinese where the apparatus is
intended to be used.
When information with regard to safety is required
according to this standard, this information shall be
given in an instruction for installation or use and
supplied with the apparatus. This information shall
be given in simplify Chinese where the apparatus is
intended to be used.
Pass
15.1.1 first sentence replaced by:
Plugs and appliance couplers for the connection of
the apparatus to the MAINS and socket-outlets and
interconnection couplers for providing MAINS
power to other apparatus shall comply with the
Chinese National standards, Industrial standards or
relevant IEC standards for plugs and socket-
outlets, appliance couplers or interconnection
couplers.
Plugs and appliance couplers for the connection of
the apparatus to the MAINS and socket-outlets and
interconnection couplers for providing MAINS
power to other apparatus shall comply with the
Chinese National standards, Industrial standards or
relevant IEC standards for plugs and socket-
outlets, appliance couplers or interconnection
couplers.
Pass
Page 56 of 62 Report No. SH10011244-001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
APPENDIX National differences for KOREA
(These differences are taken from IEC 60065(2001) + Amendment 1 (2005).)
5.101
Other marking ; Wording "
“ or an
information regulated in IEC Publication 417 giving
high voltage warning to layman shall
be marked, if an apparatus contains a part more
than 600volts.
high voltage warning to layman shall
be marked, if an apparatus contains a part more
than 600volts.
N/A
15.1.1
Plugs for the connection of the apparatus to the
supply mains and socket outlets for providing
mains power to other apparatus shall
comply with the Korean requirements (KSC8300
and 8305).
supply mains and socket outlets for providing
mains power to other apparatus shall
comply with the Korean requirements (KSC8300
and 8305).
Pass
31
Radio frequency interference
The apparatus shall comply with the relevant
CISPR requirements.(EMC = EMI + EMS)
The apparatus shall comply with the relevant
CISPR requirements.(EMC = EMI + EMS)
Pass
APPENDIX National differences for SINGAPORE
(These differences are taken from IEC60065:1992 and adopted to IEC
60065:2001.)
60065:2001.)
Throughout the standard,
whenever the words “white pine board” appear, insert the
words “or plywood board” to it.
Pass
SS 143 Amendment No.1 and No. 2
Pass
4.1.3
Delete “45 % to 75 %” and insert “65 _ 5 %”.
75% maximum in IEC
60065:2001
60065:2001
Pass
7.1
Resistance to heat without external forces
Adopt the temperature specified for the tropical
conditions.
conditions.
Pass
9.3.4
Delete the note “A Quality Assessment System for
capacitors complying with Subclause 14.2 is under
consideration in the IEC”.
capacitors complying with Subclause 14.2 is under
consideration in the IEC”.
This is not in IEC 60065:2001.
Pass
10.2 Humidity
treatment
Adopt the testing conditions designed for tropical
conditions.
conditions.
120h at a relative humidity of
93%, ambient temperature
40oC
93%, ambient temperature
40oC
Pass
Page 57 of 62 Report No. SH10011244-001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
16
External flexible cords
Delete “IEC Publication 227: Polyvinyl Cloride
Insulated Cables of Rated Voltages up to and
Including 450/750 V and IEC Publication 245:
Rubber Insulated Cables of Rated Voltage up to
and including 450/750V” and insert “Singapore
Standard 236: Flexible Cords”, whenever they
appear in this clause.
Insulated Cables of Rated Voltages up to and
Including 450/750 V and IEC Publication 245:
Rubber Insulated Cables of Rated Voltage up to
and including 450/750V” and insert “Singapore
Standard 236: Flexible Cords”, whenever they
appear in this clause.
Delete “CEE Publication 13, CEE Publication 2 and
IEC Publication 173: Colours of the Cores of
Flexible Cables and Cords” whenever they appear
in this clause.
IEC Publication 173: Colours of the Cores of
Flexible Cables and Cords” whenever they appear
in this clause.
Pass
16.2
Delete the notes in small print and insert “A
nominal cross-sectional area of 0.75 mm2 will
satisfy this requirement”.
nominal cross-sectional area of 0.75 mm2 will
satisfy this requirement”.
Pass
Page 58 of 62 Report No. SH10011244-001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
16.4b
Delete “Subclause 3.1 of IEC Publication 227-2:
Part 2: Test Methods” and insert “Subclause 9.1 of
SS 236”:
Part 2: Test Methods” and insert “Subclause 9.1 of
SS 236”:
9.1 Flexing Test (except for tinsel cords, twisted
twin and single core cords).
twin and single core cords).
The test shall be carried out by mieans of the
apparatus shown in Figure 5. This apparatus has a
carrier C supporting two pulleys A and B arranged
so that the cord is horizontal between the pulleys.
The carrier moves backward and forward over a
distance of 1 m at an approximately constant speed
of 0.33 m/s.
apparatus shown in Figure 5. This apparatus has a
carrier C supporting two pulleys A and B arranged
so that the cord is horizontal between the pulleys.
The carrier moves backward and forward over a
distance of 1 m at an approximately constant speed
of 0.33 m/s.
A sample of flexible cord fabout 5 m long shall be
stretched over the pulleys as shown in the figure,
each end being loaded with a weight. The weight
and the diameter of the pulleys A and B shall be as
given in Table 1.
stretched over the pulleys as shown in the figure,
each end being loaded with a weight. The weight
and the diameter of the pulleys A and B shall be as
given in Table 1.
Screene cords in accordance with Table 7 shall be
tested before application of the screen and outer
sheath.
tested before application of the screen and outer
sheath.
The pulleys shall have a semi-circular shaped
groove for circular cords and a flat groove for
parallel twin cords. The
groove for circular cords and a flat groove for
parallel twin cords. The
restraining clamps D shall be fixed so that the pull
is always applied by the weight from which the
carrier is mowing away. The carrier shall make 30
000 backward and forward movements (60 000
single strokes). Each conductor of the sample shall
be loaded with the current specified in Table 2.
is always applied by the weight from which the
carrier is mowing away. The carrier shall make 30
000 backward and forward movements (60 000
single strokes). Each conductor of the sample shall
be loaded with the current specified in Table 2.
For twin cords and for light PVC-sheated 3-core
cords, the voltage between the conductors shall be
approximately 230 V a.c. For all other cords having
three or more cores a three-phase a.c. voltage of
about 400 V shall be applied to three conductors,
any additional conductors being connected to the
neutral.
cords, the voltage between the conductors shall be
approximately 230 V a.c. For all other cords having
three or more cores a three-phase a.c. voltage of
about 400 V shall be applied to three conductors,
any additional conductors being connected to the
neutral.
During the test no open-circuit in any core or short-
circuit between cores shall occur.
circuit between cores shall occur.
After the test, any sheath on cords having three or
more cores shall be removed. The cord, or the laid
up cores, shall then withstand the voltage test
specified in Subclause 8.2. or 8.3 as appropriate,
but with a test voltage not exceeding 2000 V.
more cores shall be removed. The cord, or the laid
up cores, shall then withstand the voltage test
specified in Subclause 8.2. or 8.3 as appropriate,
but with a test voltage not exceeding 2000 V.
TABLE 1, TABLE 2, FIGURES 4 and 5, see the CB
bulletin.
bulletin.
Pass
*In parenthesis: clauses according to IEC60065:1992.
Click on the first or last page to see other HS 2X0 service manuals if exist.