DOWNLOAD Harman Kardon HS 100 EU (serv.man14) Service Manual ↓ Size: 3.81 MB | Pages: 52 in PDF or view online for FREE

 

 

page 4 of  51 

Ref. No. : JSH05090075-001 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

3 GENERAL 

REQUIREMENTS 

Pass 

 

Safety class of the apparatus ................................. : ClassII Pass 

 

 

 

4 

GENERAL CONDITIONS OF TESTS 

 

4.1.4 Ventilation 

instructions 

require the use of the test 

box 

Yes  

Noted 

 

 

 

5 MARKING 

Pass 

 

Comprehensible and easily discernible 

Printed on the rear enclosure 

Pass 

 

Permanent durability against water and petroleum 
spirit 

 Pass 

5.1 Identification, 

maker, model ................................... : harman/kardon Pass 

 

Class II symbol if applicable 

 

Pass 

 

Rated supply voltage and symbol .......................... : 100-240V ~ 

Pass 

 

Frequency if safety dependant 

50/60Hz Pass 

 

Rated current or power consumption .................... : 380W Pass 

5.2 Earth 

terminal 

Class II 

N/A 

 

Hazardous live terminals 

 N/A 

 

Supply output terminals (other than mains) 

 N/A 

5.3 

Use of triangle with exclamation mark 

On PCB  

Pass 

5.4 

Instructions for use 

 

Pass 

5.4.1 

Mains powered equipment not exposed to dripping 
or splashing. Warning concerning objects filled 
with liquid, etc. 

 Pass 

 

Hazardous live terminals, instructions for wiring 

No such terminals 

N/A 

 

Instructions for replacing lithium battery 

No lithium battery 

N/A 

 

Instructions for modem if fitted 

No modem fitted 

N/A 

 

Class I earth connection warning 

 

N/A 

 

Instructions for multimedia system connection 

 

Pass 

 

Special stability warning for fixed installation 

 

N/A 

5.4.2 

Disconnect device: plug/coupler or all-pole mains 
switch location, accessibility and markings 

 Pass 

 

Instructions for permanently connected equipment   

N/A 

 
 

 

 

page 5 of  51 

Ref. No. : JSH05090075-001 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

6 HAZARDOUS 

RADIATION 

Pass 

6.1 

Ionizing radiation < 36 pA/kg (0,5 mR/h) 

No ionizing radiation 

N/A 

6.1 

EN 60065 

European Council Directive 96/29/Euratom of 13 
May 1996 10cm from outer surface of apparatus 
<1µSv/h (0,1mR/h) 

No ionizing radiation 

N/A 

6.2 

Laser radiation, emission limits to IEC 60825-1  .... :  Class 1 

Pass 

 

Emission limits under fault conditions .................... :  Laser Optical Pickup:Class 1 

Pass 

 

 

 

7 

HEATING UNDER NORMAL OPERATING CONDITIONS 

Pass 

7.1 

Temperature rises not exceeding specified values, 
no operation of fuse links 

(see appended table) 

Pass 

7.1.1 

Temperature rise of accessible parts 

(see appended table) 

Pass 

7.1.2 

Temperature rise of parts providing electrical 
insulation 

(see appended table) 

Pass 

7.1.3 

Temperature rise of parts acting as a support or as a 
mechanical barrier 

(see appended table) 

Pass 

7.1.4 

Temperature rise of windings 

(see appended table) 

Pass 

7.1.5 

Parts not subject to a limit under 7.1.1 to 7.1.4 

(see appended table) 

Pass 

7.2 

Softening temperature of insulating material 
supporting parts conductively connected to the 
mains carrying a current > 0,2 A at least 150

 o

C 

No such supporting parts 

N/A 

 

 

 

8 

CONSTRUCTIONAL REQUIREMENTS WITH REGARD TO THE PROTECTION 
AGAINST ELECTRIC SHOCK 

Pass 

8.1 

Conductive parts covered by lacquer, paper, 
untreated textile oxide films and beads etc. 
considered to be bare 

PCB, windings 

Pass 

8.2 

No shock hazard when changing voltage setting 
device, fuse-links or handling drawers etc. 

Tools are required 

Pass 

8.3 

Insulation of hazardous live parts not provided by 
hygroscopic material 

No hygroscopic material used 

Pass 

8.4 

No risk of electric shock following the removal of a 
cover which can be removed by hand 

Tools are required 

Pass 

8.5 

Class I equipment 

 

N/A 

 

Basic insulation between hazardous live parts and 
earthed accessible parts 

 N/A 

 

Resistors bridging basic insulation complying with 
14.2.1 a) 

 N/A 

 

 

page 6 of  51 

Ref. No. : JSH05090075-001 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

8.6 

Class II equipment and Class II constructions within 
Class I equipment 

 Pass 

 

Reinforced or double insulation between hazardous 
live parts and accessible parts 

 Pass 

 

Components bridging reinforced or double insulation 
complying with 14.1 a) or 14.3 

TR1, TR2 

Pass 

 

Basic and supplementary insulation each being 
bridged by a capacitor complying with 14.2.1 a) 

 N/A 

 

Reinforced or double insulation being bridged with 2 
capacitors in series complying with 14.2.1 a) 

 N/A 

 

Reinforced or double insulation being bridged with a 
single capacitor complying with 14.2.1 b) 

CY1, CY2, CY3, CY4, CY5, 
CY6 

Pass 

 

Basic insulation bridged by components complying 
with 14.3.4.3 

 N/A 

8.7 

Basic insulation between parts at 35 V to 71 V 
(peak) a.c. or 60 V to 120 V d.c. and accessible 
parts 

No such voltage 

N/A 

 

Reinforced or double insulation between circuits 
operating at voltages between 35 V and 71 V (peak) 
a.c. or between 60 V and 120 V d.c. and hazardous 
live parts at higher voltage 

 N/A 

 

Separation by Class II isolating transformer 

 

N/A 

 

Separation by Class I transformer 

 

N/A 

 

Separation by earthed conductive part 

 

N/A 

8.8 

Basic or supplementary insulation > 0,4 mm (mm) :   

N/A 

 

Reinforced insulation > 0,4 mm (mm) .................... :  TR1, TR2 bobbin: 0.8mm 

Optocoupler PH1, PH2: 
0.45mm 

Enclosure: >1.1mm 

Separation sheet on internal 
enclosure under power board: 
0.5mm. 

Pass 

 

Thin sheet insulation 

Inside TR1, TR2 

Pass 

 

Basic or supplementary insulation, at least two 
layers, each meeting 10.3 

 N/A 

 

Basic or supplementary insulation, three layers any 
two of which meet 10.3 

 N/A 

 

Reinforced insulation, two layers each of which meet 
10.3 

 N/A 

 

 

page 7 of  51 

Ref. No. : JSH05090075-001 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

 

Reinforced insulation, three layers any two which 
meet 10.3 

Withstand 4240Vp test. 

Pass 

8.9 

Adequate insulation between internal hazardous live 
conductors and accessible parts 

           

N/A 

 

Adequate insulation between internal hazardous live 
parts and conductors connected to accessible parts 

           

N/A 

8.10 

Double insulation between conductors connected to 
the mains and accessible parts 

Live wires are double 
insulated, no secondary wire 
can come closer to live parts 

Pass 

8.11 

Detaching of wires 

      

N/A 

 

No undue reduction of creepages or clearance 
distances if wires become detached 

Mating lock connector used for 
mains. No risk of detached. 

N/A 

 Vibration 

test carried out  ........................................ :  No, see above 

N/A 

8.12 

Adequate cross-sectional area of internal wiring to 
mains socket-outlets 

 N/A 

8.13 

Adequate fastening of windows, lenses, lamp covers 
etc. (pull test 20 N for 10 s) 

 Pass 

8.14 

Adequate fastening of covers (pull test 50 N for 10 s)  Pass 

8.15 

No risk of damage to the insulation of internal wiring 
due to hot parts or sharp edges 

Internal wires secured and 
keep enough distance from 
sharp or hot parts. 

Pass 

8.16 

Only special supply equipment can be used 

 N/A 

8.17 

Insulated winding wire without additional interleaved 
insulation 

 N/A 

8.18 

Endurance test as required by 8.17 

 

N/A 

8.19 

Disconnection from the mains 

 

Pass 

8.19.1 

Disconnect device 

Mains plug, power inlet 

Pass 

 

All-pole switch or circuit breaker with >3mm contact 
separation 

Not used as a disconnect 
device 

N/A 

8.19.2 

Mains switch ON indication 

Not used as a disconnect 
device 

N/A 

8.20 

Switch not fitted in the mains cord 

 

Pass 

8.21 

Bridging components comply with clause 14 

 

N/A