DOWNLOAD Harman Kardon HS 100 EU (serv.man14) Service Manual ↓ Size: 3.81 MB | Pages: 52 in PDF or view online for FREE

 

 

page 20 of  51 

Ref. No. : JSH05090075-001 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

 

 

 

18 

MECHANICAL STRENGTH OF PICTURE TUBES AND PROTECTION AGAINST 
THE EFFECTS OF IMPLOSION 

N/A 

 

Picture tube separately approved to IEC 61965: 

No picture tube 

N/A 

 

Picture tube separately approved to 18.1 ............... No 

N/A 

18.1 

Picture tubes > 16 cm intrinsically protected 

           

N/A 

 

Non-intrinsically protected tubes > 16 cm used with 
protective screen 

           

N/A 

18.2 

Intrinsically protected tubes: tests on 12 samples 

           

N/A 

18.2.1 

Samples subject to ageing: 6 

      

N/A 

18.2.2 

Samples subject to implosion test: 6 

           

N/A 

18.2.3 

Samples subject to mechanical strength test (steel 
ball): 6 

           

N/A 

18.3 

Non-intrinsically protected tubes tested to 18.3 

           

N/A 

 

 

 

19 

STABILITY AND MECHANICAL HAZARDS 

Pass 

 

Mass of the equipment exceeding 7 kg  ................. : 4.6kg 

N/A 

 

Apparatus intended to be fastened in place – 
suitable instructions 

No 

N/A 

19.1 

Test on a plane, inclined at 10

o

 to the horizontal 

 

N/A 

19.2 

100 N force applied vertically downwards 

 

N/A 

19.3 

Apparatus mass > 25 kg or height > 1 M or 
supplied with cart or stand 

 N/A 

19.4 

Edges or corners not hazardous 

 

Pass 

19.5 

Glass surfaces with an area exceeding 0,1 m² or 
maximum dimension > 450 mm, pass the test of 
19.5.1 

No glass surface 

N/A 

19.6 

Wall or ceiling mountings adequate 

Not for wall or ceiling mounting 

N/A 

 

 

 

20 

RESISTANCE TO FIRE 

Pass 

20.1 

Electrical components and mechanical parts 

Pass 

 

a) Exemption for components contained in an 
enclosure of material V-0 to IEC 60707 with 
openings not exceeding 1 mm in width 

 N/A 

 

b) Exemption for small components as defined in 
20.1 

 Pass 

 

 

page 21 of  51 

Ref. No. : JSH05090075-001 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

20.1.1 Electrical 

components 

meet the requirements of 

Clause 14 or 20.1.4 

See components list 

Pass 

20.1.2 

Insulation of internal wiring working at voltages 
> 4 Kv or leaving an internal fire enclosure, not 
contributing to the spread of fire 

 N/A 

20.1.3 

Material of printed circuit boards on which the 
available power exceeds 15 W at a voltage 
between 50 V and 400 V (peak) a.c. or d.c. meets 
V-1 or better to IEC60707, unless used in a fire 
enclosure 

See components list 

Pass 

 

Material of printed circuit boards on which the 
available power exceeds 15 W at a voltage >400 V 
(peak) a.c. or d.c. meets V-0 to IEC 60707 

 Pass 

20.1.4 

Components and parts not covered by 20.1.1, 
20.1.2 and 20.1.3 (other than fire enclosures) 
mounted nearer to a potential ignition source than 
the distances in Table 21 comply with the relevant 
flammability category in Table 21 

See components list 

Pass 

 

Components and parts as above but shielded from 
a potential ignition source, with the barrier area in 
accordance with Table 21 and fig. 13 

 

N/A 

20.2 Fire 

enclosure 

 

N/A 

20.2.1 

Potential ignition sources with open circuit voltage 
> 4 kV (peak) a.c. or d.c. contained in a fire 
enclosure to V-1 

 

N/A 

20.2.2 

Internal fire enclosures with openings not 
exceeding 1 mm in width and with openings for 
wires completely filled 

 N/A 

20.2.3 

Requirements of 20.2.1 and 20.2.2 met by an 
internal fire enclosure 

 N/A 

 

 

 

 

A 

APPENDIX A, ADDITIONAL REQUIREMENTS FOR APPARATUS WITH 
PROTECTION AGAINST SPLASHING WATER 

N/A 

A.5.1 

j) Marked with IPX4 (IEC 60529), 5.4.1 a) does not 
apply 

IP20 

N/A 

A.10.2.1 

Enclosure provides protection against splashing 
water 

 

N/A 

A.10.2.2 Humidity 

treatment carried out for 7 days 

 

N/A 

 

 

page 22 of  51 

Ref. No. : JSH05090075-001 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 
 

B 

APPENDIX B, APPARATUS TO BE CONNECTED TO THE 
TELECOMMUNICATION NETWORKS 

N/A 

 

Complies with IEC 62151 clause 1 

Not to be connected to the 
telecommunication networks 

N/A 

 

Complies with IEC 62151 clause 2 

 

N/A 

 

Complies with IEC 62151 clause 3 but with 3.5.4 
modified to 2.4.10 of this standard 

 

N/A 

 

Complies with IEC 62151 clause 4 but with 4.1.2, 
4.1.3 and 4.2.1.2 modified in accordance with 
annex B of this standard 

 

N/A 

 

Complies with IEC 62151 cause 5 but with 5.3.1 
modified in accordance with annex B of this 
standard 

 

N/A 

 

Complies with IEC 62151 clause 6  

 

N/A 

 

Complies with IEC 62151 clause 7  

 

N/A 

 

Complies with IEC 62151 annex A, B and C 

 

N/A 

 
 
 

 

 

page 23 of  51 

Ref. No. : JSH05090075-001 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065D 

 

     TRF originator BEAB 

7.1 

TABLE: temperature rise measurements 

Pass 

 

Power consumption in the OFF/Stand-by 

Stand-by: <1.3W  

Pass 

 

Position of the functional switch (W) ...................... : -- 

— 

 

Operating conditions 

Normal DVD playing, with 1/8 non-clipped 1kHz sinusoidal output power to the speaker, operates 4 hours until 
steady condition reached. Ambient 23.5

o

C. 

Un (V) 

In (A) 

Pn (W) 

Pout (W) 

90 0.78 44.4 N.A. 

100 0.71 44.0 N.A. 

240 0.38 45.0 N.A. 

264 0.35 45.0 N.A. 

 

      

Loudspeaker impedance (Ω) ................................. : 6 Ω X 5 

— 

      

Several loudspeaker systems 

5 channel speakers 

Pass 

           

Marking of loudspeaker terminals 

Printed on rear enclosure 

Pass 

Monitored point: 

dT (K)              

264V / 90V 

Limit dT (K) 

Power cord 

26.2/ 27.1 

60 

Winding of LF1 

31.4 / 43.8 

65* 

Y capacitor: CY1 

23.6 / 30.1 

50 (85-35) 

X capacitor: CX1 

28.3 / 37.4 

65 (100-35) 

Winding of LF1 

31.8 / 51.8 

65* 

Electrolytic capacitor: EC16 

33.1 / 37.3 

70 (105-35) 

X capacitor: CX2 

29.0 / 36.4 

65 (100-35) 

PCB near BG1 

33.7/ 43.9 

75 

Winding of TR1 

46.2 / 41.0 

65* 

Bobbin of TR1 

45.8 / 40.5 

115 (150-35) 

PCB near TR1 

39.2 / 37.0 

75 

Optocoupler: PH1 

31.1 / 30.3 

-- 

Winding of TR2 

44.4 / 38.4 

65* 

Bobbin of TR2 

46.4 / 39.9 

115 (150-35) 

PCB near TR2 

40.3 / 37.1 

75 

Y capacitor: CY5 

37.4 / 34.1 

50 (85-35)