Harman Kardon HK 970 (serv.man13) EMC - CB Certificate ▷ View online
Page 5 of 66
Report No.: HK-R04173361
IEC 60065 / EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN60065D
Intertek Testing Services Hong Kong Ltd.
2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong.
Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com
Instructions for multimedia system connection
N
Special stability warning for fixed installation
N
5.4.2
Disconnect device: plug/coupler or all-pole mains
switch location, accessibility and markings
switch location, accessibility and markings
Mains plug used as disconnect
device
device
P
Instructions for permanently connected equipment Not a permanently connected
equipment
N
6 HAZARDOUS
RADIATION
6.1 Ionizing
radiation
≤ 36 pA/kg (0,5 mR/h)
No such radiation
N
6.2
Laser radiation, emission limits to IEC 60825-1 .... : No such radiation
N
Emission limits under fault conditions ................... :
N
7
HEATING UNDER NORMAL OPERATING CONDITIONS
7.1
Temperature rises not exceeding specified values,
no operation of fuse links
no operation of fuse links
(see appended table)
P
7.1.1
Temperature rise of accessible parts
(see appended table)
P
7.1.2
Temperature rise of parts providing electrical
insulation
insulation
(see appended table)
P
7.1.3
Temperature rise of parts acting as a support or as
a mechanical barrier
a mechanical barrier
N
7.1.4 Temperature
rise
of
windings
(see appended table)
P
7.1.5
Parts not subject to a limit under 7.1.1 to 7.1.4
N
7.2
Softening temperature of insulating material
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150
o
C
N
Page 6 of 66
Report No.: HK-R04173361
IEC 60065 / EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN60065D
Intertek Testing Services Hong Kong Ltd.
2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong.
Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com
8
CONSTRUCTIONAL REQUIREMENTS WITH REGARD TO THE PROTECTION
AGAINST ELECTRIC SHOCK
AGAINST ELECTRIC SHOCK
8.1
Conductive parts covered by lacquer, paper,
untreated textile oxide films and beads etc.
considered to be bare
untreated textile oxide films and beads etc.
considered to be bare
Not used
P
8.2
No shock hazard when changing voltage setting
device, fuse-links or handling drawers etc.
device, fuse-links or handling drawers etc.
Tools are required
N
8.3
Insulation of hazardous live parts not provided by
hygroscopic material
hygroscopic material
No such material
P
8.4
No risk of electric shock following the removal of a
cover which can be removed by hand
cover which can be removed by hand
Clause 8.6 was complied
P
8.5
Class I equipment
Basic insulation between hazardous live parts and
earthed accessible parts
earthed accessible parts
Class II apparatus
N
Resistors bridging basic insulation complying with
14.2.1 a)
14.2.1 a)
N
8.6
Class II equipment and Class II constructions
within Class I equipment
within Class I equipment
N
Reinforced or double insulation between
hazardous live parts and accessible parts
hazardous live parts and accessible parts
Class II apparatus
P
Page 7 of 66
Report No.: HK-R04173361
IEC 60065 / EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN60065D
Intertek Testing Services Hong Kong Ltd.
2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong.
Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com
Components bridging reinforced or double
insulation complying with 14.1 a) or 14.3
insulation complying with 14.1 a) or 14.3
1. Creepage
distance
and
clearance measured on
power switch board which
between:
power switch board which
between:
− Primary and secondary of
relay (RL901): 6,7mm
− Soldering pad of power cord
wire (AC1) and metal
enclosure (through screw
post): 6,65mm
enclosure (through screw
post): 6,65mm
− Soldering pad of mains
fuse-link (FUSE) and metal
enclosure (through screw
post): 6,25mm
enclosure (through screw
post): 6,25mm
− Track of L901 and metal
enclosure (through screw
post): 6,25mm
post): 6,25mm
− Track of R901 and metal
enclosure (through screw
post): 6,35mm
post): 6,35mm
− Track of primary lead wire of
mains transformer and metal
enclosure (through screw
post): 7,85mm
enclosure (through screw
post): 7,85mm
(Limits: (Cr.)
≥ 4,6mm;
(Cl.)
≥ 4,0mm)
2. Clearance
measured
between:
− Soldering terminal of
primary lead wire of mains
transformer (T1) on power
switch board and metal
enclosure: 8,55mm
transformer (T1) on power
switch board and metal
enclosure: 8,55mm
− Primary winding of mains
transformer and metal
enclosure: 19,3mm
enclosure: 19,3mm
(Limits:
≥ 4,0mm)
P
Page 8 of 66
Report No.: HK-R04173361
IEC 60065 / EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN60065D
Intertek Testing Services Hong Kong Ltd.
2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong.
Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com
(Cont’d)
Components bridging reinforced or double
insulation complying with 14.1 a) or 14.3
insulation complying with 14.1 a) or 14.3
3. Creepage
distance
and
clearance of mains
transformer between:
transformer between:
− Primary winding and
accessible iron core (along
bobbin): 7,4mm
bobbin): 7,4mm
− Primary winding and
secondary winding (along
bobbin): 8,27mm
bobbin): 8,27mm
− Primary winding and
secondary winding (via iron
core): 7,4mm
core): 7,4mm
(Limits: (Cr.)
≥ 4,6mm;
(Cl.)
≥ 4,0mm)
4. Clearance
of
mains
transformer between:
− Primary winding and
accessible iron core (along
bobbin): 7,8mm
bobbin): 7,8mm
(Limits:
≥ 4,0mm)
5. Creepage
distance
and
clearance of stand-by
transformer between:
transformer between:
− Primary winding and
accessible iron core:
6,15mm
6,15mm
− Primary winding and
secondary winding (via iron
core): 7,35mm
core): 7,35mm
(Limits: (Cr.)
≥ 4,6mm;
(Cl.)
≥ 4,0mm)
P
Basic and supplementary insulation each being
bridged by a capacitor complying with 14.2.1 a)
bridged by a capacitor complying with 14.2.1 a)
Mains and stand-by
transformers
transformers
P
Reinforced or double insulation being bridged with
2 capacitors in series complying with 14.2.1 a)
2 capacitors in series complying with 14.2.1 a)
No such component
N
Reinforced or double insulation being bridged with
a single capacitor complying with 14.2.1 b)
a single capacitor complying with 14.2.1 b)
No such component
N
Basic insulation bridged by components complying
with 14.3.4.3
with 14.3.4.3
No such component
N
Click on the first or last page to see other HK 970 (serv.man13) service manuals if exist.