DOWNLOAD Harman Kardon DVD 23 (serv.man11) Service Manual ↓ Size: 2.88 MB | Pages: 65 in PDF or view online for FREE

 

 

page 31 of  63 

Ref. No. : JSH05110330-002 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

 

NO: method b) of 8.1 is not permitted. Double or 
reinforced insulation is required between parts 
connected to the mains and parts connected to the 
public telecommunications network 

           

N/A 

J.2 

NO: In Norway, due to IT power distribution system 
used, the a.c. MAINS supply voltage is considered 
to be equal to the line-to-line voltage, and will 
remain 230V in case of a single earth fault. 

 Pass 

 

ZC 

ANNEX ZC TO EN 60065, A-DEVIATIONS 

N/A 

5 

DE: additional markings required in German language: 

N/A 

 

- cathode ray tubes with an accelerating voltage 
between 20 kV and 30 kV (marking on the tube) 

           

N/A 

 

- TV receivers whose picture tube has an 
accelerating voltage between 20 kV and 30 kV 

           

N/A 

 

- TV receivers whose picture tube has an 
accelerating voltage greater than 30 kV 

           

N/A 

 

- TV receivers whose picture tube has an 
accelerating voltage less than 20 kV 

           

N/A 

5.1 

IT: additional markings on the outside of the TV 
receiver in Italian language 

           

N/A 

 

IT: user instructions in Italian language including a 
conformity declaration 

           

N/A 

 

IT: certification number on the back cover 

           

N/A 

14 

SE: Switches containing mercury such as 
thermostats, relays and level controllers are not 
allowed. 

No such part 

N/A 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

page 32 of  63 

Ref. No. : JSH05110330-002 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

 

National differences for CHINA 
(According to CB bulletin No. 107A. These differences are taken from 
IEC60065:1993 and adopted to IEC 60065:2001.) 

Pass 

 

IEC 60065 sub-clause 4.2.2: Test voltage is 0.9 
times or 1.06 times rated voltage of the 
equipment; GB8898 sub-clause 4.2.2: Test 
voltage is 0.9 times or 1.1 times rated voltage of 
the equipment, which of the equipment used in 
China shall cover 220V±10%, 50Hz. 

 Pass 

 

IEC standard for plug is IEC 60083; The Chinese 
national standard for Plugs is GB1002-1996, 
which is not equivalent with IEC 60083 

 Pass 

 
 

 

National differences for KOREA 
(According to CB bulletin No. 107A. These differences are taken from 
IEC60065:1998 and adopted to IEC 60065:2001.) 

Pass 

5.101 

Other marking ; Wording "____ “ or an 
information regulated in IEC Publication 417 
giving high voltage warning to layman shall 
be marked, if an apparatus contains a part more 
than 600volts. 

 N/A 

15.1.1 

Plugs for the connection of the apparatus to the 
supply mains and socket outlets for providing 
mains power to other apparatus shall 
comply with the Korean requirements (KSC8300 
and 8305). 

 Pass 

31 

Radio frequency interference 
The apparatus shall comply with the relevant 
CISPR requirements.(EMC = EMI + EMS) 

 Pass 

 

 

National differences for SINGAPORE 
(According to CB bulletin No. 107A. These differences are taken from 
IEC60065:1993 and adopted to IEC 60065:2001.) 

Pass 

 

Throughout the standard, whenever the words "white pine board" appear, insert 
the words "or plywood board" to it. 

Noted 

 

SS 143 Amendment No.1 and No. 2 

 

4.1.3 

Delete "45 % to 75 %" and insert "65 _ 5 %". 

75% maximum in IEC 
60065:2001 

Noted 

7.1 

Resistance to heat without external forces 
Adopt the temperature specified for the tropical 
conditions. 

 Pass 

8.6 

(9.3.4)* 

Delete the note "A Quality Assessment System 
for capacitors complying with Subclause 14.2 is 
under consideration in the IEC". 

This is not in IEC 60065:2001. 

Noted 

10.2 

Humidity treatment 
Adopt the testing conditions designed for tropical 
conditions. 

120h at a relative humidity of 
93%, ambient temperature 
40

o

C 

Pass 

 

 

page 33 of  63 

Ref. No. : JSH05110330-002 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

16 

External flexible cords 
Delete "IEC Publication 227: Polyvinyl Cloride 
Insulated Cables of Rated Voltages up to and 
Including 450/750 V and IEC Publication 245: 
Rubber Insulated Cables of Rated Voltage up to 
and including 450/750V" and insert "Singapore 
Standard 236: Flexible Cords", whenever they 
appear in this clause. 
Delete "CEE Publication 13, CEE Publication 2 
and IEC Publication 173: Colours of the Cores of 
Flexible Cables and Cords" whenever they 
appear in this clause. 

 Noted 

16.2 

Delete the notes in small print and insert "A 
nominal cross-sectional area of 0.75 mm

2

 will 

satisfy this requirement". 

 Noted 

16.3b 

(16.4b)* 

Delete "Subclause 3.1 of IEC Publication 227-2: 
Part 2: Test Methods" and insert "Subclause 9.1 
of SS 236": 
9.1 Flexing Test (except for tinsel cords, twisted 
twin and single core cords). 
The test shall be carried out by mieans of the 
apparatus shown in Figure 5. This apparatus has 
a carrier C supporting two pulleys A and B 
arranged so that the cord is horizontal between 
the pulleys. The carrier moves backward and 
forward over a distance of 1 m at an 
approximately constant speed of 0.33 m/s. 
A sample of flexible cord fabout 5 m long shall be 
stretched over the pulleys as shown in the figure, 
each end being loaded with a weight. The weight 
and the diameter of the pulleys A and B shall be 
as given in Table 1. 
Screene cords in accordance with Table 7 shall 
be tested before application of the screen and 
outer sheath. 
The pulleys shall have a semi-circular shaped 
groove for circular cords and a flat groove for 
parallel twin cords. The 
restraining clamps D shall be fixed so that the pull 
is always applied by the weight from which the 
carrier is mowing away. The carrier shall make 30 
000 backward and forward movements (60 000 
single strokes). Each conductor of the sample 
shall be loaded with the current specified in Table 
2. 
For twin cords and for light PVC-sheated 3-core 
cords, the voltage between the conductors shall 
be approximately 230 V a.c. For all other cords 
having three or more cores a three-phase a.c. 
voltage of about 400 V shall be applied to three 
conductors, any additional conductors being 
connected to the neutral. 
During the test no open-circuit in any core or 

 Noted 

 

 

page 34 of  63 

Ref. No. : JSH05110330-002 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

short-circuit between cores shall occur. 
After the test, any sheath on cords having three 
or more cores shall be removed. The cord, or the 
laid up cores, shall then withstand the voltage 
test specified in Subclause 8.2. or 8.3 as 
appropriate, but with a test voltage not exceeding 
2000 V. 
TABLE 1, TABLE 2, FIGURES 4 and 5, see the 
CB bulletin. 

*In parenthesis: clauses according to IEC60065:1993. 
 

 

National differences MALAYSIA, according to CB bulletin No. 107A 
IEC 60065, 7th ed. 

Pass 

 

The supply voltage in Malaysia is 240 Vac, at 
50Hz. 

 Pass 

 

Class 0 and 01 appliances are not allowed 

 Pass 

 

13A fused plug-tops shall comply to Malaysian 
standard (MS 589:Part1:1997), if applicable. 

Same as BS1363 type. 

Pass 

 

2-pin plug tops shall comply to Malaysian 
standard (MS 1578:2003) if applicable 

 N/A 

 
 

 

(IEC Publication 60065:2001) 

Pass 

1.1.1 

- Scope clarification: 
The standard also covers commercial and 
professional apparatus; professional apparatus 
may also be investigated using UL 1419. 
Projection apparatus is not covered. Household 
games, household gaming and scoring machines, 
satellite receiver antenna positioners are covered 
by this standard but commercial games and 
commercial gaming and scoring machines, and 
other types of antenna positioners are covered by 
other standard. 
Add: Mains connected apparatus intended for field 
installation requires compliance with the National 
Electrical Code, ANSI, NFPA 70. 

 

Noted 

1.1.3 

- Protection against splashing water replaced with 
apparatus intended for outdoor use (See Annex 
A). 

 Pass 

1.1.5 

- Add: Some equipment covered by these 
requirements may also be required to comply with 
applicable requirements in other standards 

 Noted 

1.2 

- Add references to ANSI, ASTM and UL 
standards. 

 Noted 

4.2.1 

- Add Note: In the U.S. the RATED SUPPLY 
VOLTAGE for single-phase apparatus is assumed 
to be 120 V or 120/240 V. 

100-240V~ Pass