DOWNLOAD Harman Kardon DVD 23 (serv.man11) Service Manual ↓ Size: 2.88 MB | Pages: 65 in PDF or view online for FREE

 

 

page 39 of  63 

Ref. No. : JSH05110330-002 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

14.4 

- Add to Note 2: “High voltage materials shall be 
rated 94V-2 minimum.” 
Modification: Compliance is checked by meeting 
requirements for category V-2 according to UL 94. 
Moreover the requirements are added for arcing, 
component part flame and high-voltage isolating 
component tests. 

No such parts 

N/A  

 

14.4.1 

- Replace with High voltage arcing test. 

 

N/A 

14.4.2 

- Deleted. 

 N/A 

14.4.3 

- Add: High voltage component part flame test. 

 

N/A 

14.4.4 

- Add: High voltage isolation component insulation 
test. 

 N/A 

14.5.1 

- Delete reference to 14.5.1.3. 

 Noted 

14.5.1.1 

- Replace text with: Thermal cutouts shall comply 
with UL 873, UL 8730-2-9 or UL 60730-2-9. 

No such parts. 

N/A 

14.5.1.2 

- Replace text with: "Thermal links shall comply 
with UL 1020 or IEC 60691." 

No such parts. 

N/A 

14.5.1.3 

- Delete 

 Noted 

14.5.2.1 

- Modification: Fuse links shall comply with UL 
248-14 

 Pass 

14.5.2.2 

- Delete reference to IEC 60127 and breaking 
capacity marking requirements. 

 Noted 

14.5.3 

- Add: As an option, a PTC thermistor may comply 
with UL 1434. Delete the 3rd and 4th paragraphs. 

No such parts. 

N/A 

14.5.3A 

- Add: Protective devices connected to the mains 
shall have adequate breaking capacity and comply 
with UL 873, UL 1416, UL 1417 or UL 2111 as 
applicable. 

No such parts. 

N/A 

14.5.4 

- Reference to fuse-links is deleted. 

 Noted 

14.6.1 

- Add: “Switches and relays shall comply with UL 
1054, UL 61058-1 or UL 508 as applicable. Mains 
switch or relay shall be rated for the total current 
through the switch or relay contacts.” 
Replace remaining text with: “A rating of a mains 
switch or relay, provided on a audio apparatus 
intended for commercial use, is to be equal to or 
greater than the maximum steady state current it 
controls under normal operating conditions except 
the audio output is adjusted to 1/3 maximum 
undistorted output or at 1/3 of the manufacturer’s 
rated output power, whichever is greater.” 
14.6.2, 14.6.3 and 14.6.4 are deleted. 

No such parts. 

N/A 

14.6.5 

- Modification: A switch or relay that controls a 
mains socket-outlet shall have a rating equal to 
the rated current consumption of the apparatus 
plus the current rating of the socket-outlet. 

 N/A 

 

 

page 40 of  63 

Ref. No. : JSH05110330-002 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

14.6.6 

- Add: A mains switch shall comply with (a), (b) or 
(c). The contacts of a mains relay shall comply 
with (a), (b) or (d). A switch that controls a mains 
receptacle shall comply with (b) and a relay that 
controls a mains receptacle shall comply with (b) 
or (d). 

 N/A 

14.6.6a 

- Add: Switch or relay contacts to have current 
rating equal to or greater than 1.414 times the 
inrush current of the apparatus. 

 N/A 

14.6.6b 

- Add: Switch or relay to be TV rated. 

 

N/A 

14.6.6c 

- Add: Switch is located on the back of apparatus 
and is not operable from a remote control. 

 

N/A 

14.6.6d 

- Add: Relay is to be subjected to the endurance 
test. 

 

N/A 

14.6.6.1 

- Add: Peak Inrush current test 

 

N/A 

14.6.6.2 

- Add: Relay endurance test 

 N/A 

14.6.7 

- Add: Double pole switch controlling a.c. and d.c. 
circuits shall be suitable for the application. 

 N/A 

14.7 

- Add to the end of the 2nd paragraph “…except 
that the jointed test finger to in 9.1.1 is used to 
determine accessibility (IEC 60950, 2.8.2) and 
interlock operation (IEC 60950, 2.8.3).” 

No such parts. 

N/A 

14.10.6 

- Add: “An apparatus intended for use with an 
external battery shall be provided with an 
overcurrent protective device in the battery-supply 
circuit.” 

No such parts. 

N/A 

14.11 

- Add: “Component power supplies and their 
optocouplers complying with the construction and 
test requirements of UL 1310, UL 1950 Third 
Edition, or UL 60950 are considered to fulfill the 
test requirements on the clause.” 
Optocouplers bridging reinforced insulation shall 
comply with requirements for double protection as 
specified in UL 1577.  
4th paragraph reads: “External clearances and 
creepage distances of optocouplers shall comply 
with 13.1.” 

 Pass 

 

14.12 

- Replace “IEC 61051-2” with “UL 1449” and “IEC 
60707” with “UL 94.” Delete all references to “IEC 
60151”. 

 

Pass 

15.1.1 

– Add: “Attachment plug shall have a current 
rating no less than 125% of the current drawn 
under normal operating conditions and a voltage 
rating appropriate for the rated voltage of the 
apparatus. 

 Pass 

 

Attachment plugs for use on more than one supply 
voltage by means of a voltage selector shall be 
rated for the voltage, which the apparatus is 
intended to be connected when it is shipped from 
the factory. 

 N/A 

 

 

page 41 of  63 

Ref. No. : JSH05110330-002 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

 

Attachment plug cap shall be polarized when the 
apparatus is provided with a manually operated, 
line connected, single-pole switch; Edison-base 
lampholder; or a 15 or 20 A socket outlet.” 

 N/A 

15.1.2 

- Delete reference to “Banana” plug in the Note. 

 Noted 

15.1.3.1 

- Add: “An audio amplifier having an open-circuit 
audio output voltage not limited to 120 V that is 
permanently connected to the mains shall be 
provided with a means for connection complying 
with U.21.1.1 –U.21.1.7 and wire-binding screws 
No. 6-32 or larger complying with U.21.3.1 – 
U.21.3.5, or quick-connect terminals, or leads. 
Quick Connect Terminal shall comply with the 
following:  
a) Male tabs firmly mounted in place, b) Mating 
female connectors shall be provided with the 
apparatus, c) Strain Relief Test of Clause 16.5,d) 
Installation instructions shall be provided for 
assembly of terminal to a conductor and strain 
relief, e)Terminals shall be appropriate for use with 
the size and type of wire specified.” 

No such voltage. 

N/A 

15.1.3.2 

- Add: "Audio amplifiers having an audio output not 
limited to 120 V that are connected to the mains 
by a flexible cord shall have suitable cord or 
provision for field installation or a receptacle for 
plug-in connections."  

No such voltage. 

N/A 

15.2 

- Add after 3rd paragraph: “The earthing conductor 
in a supply cord, or in an interconnecting cable 
shall have an equivalent or larger cross-sectional 
area that the current-carrying conductors in the 
supply cord or cable. With reference to earthing 
conductors, the insulation color may be green or 
green/yellow. 

Class II 

N/A 

15.3.5 

- Revise 2nd paragraph to read: “For rated 
currents exceeding 13 A, reference is made to 
Article 310 of the National Electrical Code, 
ANSI/NFPA 70.” 
Table 15 - Replace with: “Nominal cross-sectional 
area AWG“ and modify values. 

 N/A 

15.4 

- Add: ”Component power supply adaptors 
complying with the construction and test 
requirements of UL 1310, UL 1950 Third Edition, 
or UL 60950 are considered to fulfill the test 
requirements on the clause.” 

 N/A 

16.1 

- Modification: Mains supply flexible cords shall 
comply with UL 817, be marked VW-1, and have 
an ampacity not less than the current drawn by the 
apparatus. Delete references to IEC 602227, 
60245 and 60173. 
Table 17A - Add: Types of cords and cord lengths 
for various types of apparatus. 

PVC, complying with 
IEC60227, UL approved 

Pass 

 

 

page 42 of  63 

Ref. No. : JSH05110330-002 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

16.2 

- An integral earthing conductor shall be at least 
the same size as the other cord conductors. 
Substitute “IEC 60950, table 3B” with “Article 400 
of the National Electrical Code”. 
Table 18 – Replace with “Wire sizes of external 
flexible cords” Upper current limit in column 1 
increased from 16 to 30 A and “AWG” wire sizes 
added. 

18AWG Pass 

16.3 

- Add: c) Flexible cords not complying with 16.1, 
used as connection between the apparatus and 
other apparatus used in combination with it, shall 
be marked VW-1. 

No such interconnection cord 
used 

N/A 

17.8 

- Expanded to include all cart/stand parts supplied 
by the manufacturer, such as casters and 
brackets. 
Suitable assembly instructions required. Add: 
"Relevant fixing means are not required when 
installation is to be done by a skilled person." 

 

N/A 

17.10 

- Add: Aluminum conductors used as internal 
wiring shall be terminated by a method capable of 
being used in the combination of metals involved 
at the connection point. 

 N/A 

17.11 

- Add: An accessory shall be investigated to 
determine that: a) The accessory, and the 
combination of the accessory and the apparatus 
shall present no hazard in the sense of this 
standard and b) The accessory 
is provided with installation instructions. 

 

N/A 

 

17.11.1 

- Add: The installation of an accessory of a skilled 
person shall be such that: a) The mechanical 
positioning is accomplished by means of tools 
normally available or by means of special tools 
provided by the organization responsible for 
providing the apparatus as part of the installation 
kit, and b) The electrical connections are made by 
using existing terminals and connections in the 
apparatus or the building wiring. 

 

N/A 

 

18 

- Modification: Non-intrinsically protected picture 
tubes shall comply with 18.1, 18.2.2 and 
18.3.Intrinsically protected picture tubes shall 
comply with UL 1418 or UL 61965. 
Add: “A bulb of a picture tube having a face 
diameter of 7.5 cm or more shall be mounted in an 
enclosure. The enclosure shall have no opening 
that exceeds 130 mm2 unless the minor 
dimension of the opening is 10 mm or less.” 

 N/A