Harman Kardon BDS 577 EMC - CB Certificate ▷ View online
Page 49 of 69
Report Reference No.: 211-2012016-000
Attachment No. 2
IEC60065
Clause
Requirement + Test
Result - Remark
Verdict
Jiangsu TÜV Product Service Ltd. - Shenzhen Branch
Test Report National and Group Differences for IEC 60065 7
th
Ed.+A1+A2 Rev. 02/ 2011-06
MY Malaysia
MY
Energy Commission circular no.1 year 2003
(no.1/2003)
States that a Certificate of Approval is required
for manufacturing, selling, Advertising, displaying
or importing into Malaysia, electrical/electronic
products Listed in Annex A.
- The supply voltage in Malaysia is 240 Vac, at
50Hz.
- Class 0 and 01 appliances are not allowed
- 13A fused plug-tops shall comply to Malaysian
standard (MS 589:Part1:1997), if applicable.
- 2-pin plug tops shall comply to Malaysian
standard (MS 1578:2003) if applicable.
(no.1/2003)
States that a Certificate of Approval is required
for manufacturing, selling, Advertising, displaying
or importing into Malaysia, electrical/electronic
products Listed in Annex A.
- The supply voltage in Malaysia is 240 Vac, at
50Hz.
- Class 0 and 01 appliances are not allowed
- 13A fused plug-tops shall comply to Malaysian
standard (MS 589:Part1:1997), if applicable.
- 2-pin plug tops shall comply to Malaysian
standard (MS 1578:2003) if applicable.
P
NO Norway
NO
13.3.1
To the second paragraph the following is added:
In Norway, due to the IT power distribution
system used, the a.c. MAINS supply voltage is
considered to be equal to the line-to-line voltage,
and will remain 230 V in case of a single earth
fault.
Justification:
Based on a use in Norway of an IT power
distribution system where the neutral is not
provided.
In Norway, due to the IT power distribution
system used, the a.c. MAINS supply voltage is
considered to be equal to the line-to-line voltage,
and will remain 230 V in case of a single earth
fault.
Justification:
Based on a use in Norway of an IT power
distribution system where the neutral is not
provided.
P
Page 50 of 69
Report Reference No.: 211-2012016-000
Attachment No. 2
IEC60065
Clause
Requirement + Test
Result - Remark
Verdict
Jiangsu TÜV Product Service Ltd. - Shenzhen Branch
Test Report National and Group Differences for IEC 60065 7
th
Ed.+A1+A2 Rev. 02/ 2011-06
NO Norway
NO
15.1.1
Mains socket-outlets mounted on CLASS II apparatus shall comply with the
specifications given in CEE Publ. 7 as fas as applicable, with the following amendments:
specifications given in CEE Publ. 7 as fas as applicable, with the following amendments:
§ 8 Dimensions
a 2,5 A 250 V two-pole socket-outlets for electronic apparatus shall comply with the
enclosed Standard Sheet I.
enclosed Standard Sheet I.
§ 24 Mechanical strength
a 2,5 A, 250 V socket-outlets for CLASS II electronic apparatus are tested as specified
in 12.1.3 of EN 60065.
in 12.1.3 of EN 60065.
Also the protecting rim shall be tested.
Justification:
Act of 24 May 1929 relating to supervision of electrical installation (TEA 1929/FEL 1998).
N/A
J2
After Table J.1 the following is added:
In Norway, due to the IT power distribution
system used, the a.c. MAINS supply voltage is
considered to be equal to the line-to-line voltage,
and will remain 230 V in case of a single earth
fault.
system used, the a.c. MAINS supply voltage is
considered to be equal to the line-to-line voltage,
and will remain 230 V in case of a single earth
fault.
Justification:
Based on a use in Norway of an IT power
distribution system where the neutral is not
provided.
distribution system where the neutral is not
provided.
P
Page 51 of 69
Report Reference No.: 211-2012016-000
Attachment No. 2
IEC60065
Clause
Requirement + Test
Result - Remark
Verdict
Jiangsu TÜV Product Service Ltd. - Shenzhen Branch
Test Report National and Group Differences for IEC 60065 7
th
Ed.+A1+A2 Rev. 02/ 2011-06
NO Norway
NO
Annex B Replace NOTE 1 by
In the CENELEC countries listed in IEC 62151,
special national conditions apply.
special national conditions apply.
Add the following:
All subclauses given below are subclauses of IEC
62151:2000 (ref. Corrigendum 1 and 2 to IEC
62151).
62151:2000 (ref. Corrigendum 1 and 2 to IEC
62151).
Subclause 4.1.1 (Corrigendum 2):
Add after the first paragraph:
NOTE - In Norway, CLASS I equipment which is
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket -outlet.
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket -outlet.
The marking text shall be as follows:
"Apparatet skal tilkoples jordet stikkontakt"
N/A
Page 52 of 69
Report Reference No.: 211-2012016-000
Attachment No. 2
IEC60065
Clause
Requirement + Test
Result - Remark
Verdict
Jiangsu TÜV Product Service Ltd. - Shenzhen Branch
Test Report National and Group Differences for IEC 60065 7
th
Ed.+A1+A2 Rev. 02/ 2011-06
NO Norway
NO
5.3.1
Add after the first test specifications paragraph:
NOTE 1 In Finland, Norway and Sweden, there
are additional requirements for the insulation.
are additional requirements for the insulation.
Renumber the existing note as note 2.
For additional requirements for the insulation in
Sweden in the NOTE 1 the following text is added
between the first and second paragraph (this text
is identical to the text in EN 60950-1:2001):
Sweden in the NOTE 1 the following text is added
between the first and second paragraph (this text
is identical to the text in EN 60950-1:2001):
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
forming part of a component, it shall at least
consist of either
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or
shall pass the electric strength test below, or
- one layer having a distance through insulation of
at least 0,4 mm, which shall pass the electric
at least 0,4 mm, which shall pass the electric
strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that
CLEARANCES and CREEPAGE DISTANCES do
not exist, if the component passes the electric
strength test in the accordance with the
compliance clause below and in addition:
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that
CLEARANCES and CREEPAGE DISTANCES do
not exist, if the component passes the electric
strength test in the accordance with the
compliance clause below and in addition:
- passes the test and inspection criteria of 13.6
with an electric strength test of 10.3 using the test
voltage of 1,5 kV multiplied by 1,6, and
with an electric strength test of 10.3 using the test
voltage of 1,5 kV multiplied by 1,6, and
- is subject to routine testing for electric strength
during manufacturing, using a test voltage of 1,5
kV (for performance of the test see N.2.1).
during manufacturing, using a test voltage of 1,5
kV (for performance of the test see N.2.1).
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
capacitor complying with IEC 60384-14:1993,
subclass Y2.
A capacitor classified Y3 according to IEC 60384-
14:1993, may bridge this insulation under the
following conditions:
14:1993, may bridge this insulation under the
following conditions:
- the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by
IEC 60384-14, which in addition to the Y3 testing,
is tested with an Impulse test of 2.5kV defined in
IEC 62151, subclause 6.2.1;
having a capacitor classified Y3 as defined by
IEC 60384-14, which in addition to the Y3 testing,
is tested with an Impulse test of 2.5kV defined in
IEC 62151, subclause 6.2.1;
- the additional testing shall be performed on all
the test specimens as described in IEC 60384-
14;
the test specimens as described in IEC 60384-
14;
N/A
Click on the first or last page to see other BDS 577 service manuals if exist.