DOWNLOAD Sony KV-38DRC2 Service Manual ↓ Size: 23.32 MB | Pages: 127 in PDF or view online for FREE

Standard ............................................................................ 135.3 ± 1 VCD

Check Condition:

 

AC input voltage: 120 (± 2) VAC at Board Adjustment Process

 

 

  130 (± 2) VAC at QC

 

 

  120 (± 2) VAC at Overall Adjustment (after aging)

Note: 

If using a stabilized power supply, make sure that the distortion 

  

factor is 3% or less. 

Setting Mode:........................................................................... Full mode

Signal Input:................................................ Cross-hatch of NTSC at QC

Initial Setting:........................................................Reset condition at QC

Confi rm Point:.......................................Across C6544 for B+ of D Board

3-1.   X RV8001, RV8002 CONFIRMATION METHOD AND HV SERVICE ADJUSTMENTS

Is T8001 

Changed?

Is D-Board 

Replaced?

Replace RV8001, RV8002  with the same value:
HV project adjust and inspection

1. Turn RV8001 fully counter-clockwise.
2.  Turn set on with black video signal then adjust RV8002 slowly to obtain 

35.5kV.

3. Turn RV8001 clockwise slowly until hold down operation initially activates.

4.  Adjust RV8002 clockwise, then turn the set on.  Change video to white field then 

slowly turn RV8002 counter-clockwise to get 34.8 ± 0.2kV. Confirm set does 
NOT TURN OFF at this condition. If yes, then repeat from step 1 again.

5.  Finally, set back RV8002 to 31.50kv + 0.2kv at video cut off (black video).

Start

No

Yes

Change any

or

marked parts

Yes

No

Yes

No

Start from

the beginning.

Yes

Is +B, Vd and

hold down

confirmed?

Finish for

hold-down

check.

Confirm +B, Vd and check hold-down on the D Board video with no signal (standard 
reset mode) as follows:

1. Confirm +B across C6544 to make sure that it is 135.3 ± 1 Vdc.
2. Confirm Vd at Pin 2 CN5506 or at TP-Vd for 4.3V < Vd < 4.65 Vdc.
3. Apply 5.5 ± 0.5 Vdc at Pin 2 of CN5506, then confirm that set holds down.

If all adjustments are complete, then seal and secure RV8001, RV8002 with 

epoxy to prevent any possible misadjustment by non-trained technical 

service.

1.  Standby mode (Power off).

2.  Press the following buttons on the Remote Commander within one 

second of each other: 

 

DISPLAY  

 Channel  5  

 Sound Volume  +  

 Power

2150P-1 

0 

+7 

SERVICE

SBOT 

 

 

TV

Device Item

Data Item

Register

Item

F/A FLAG:

CBA FLAG:

WSL: 0

1.  Enter into Service Mode.

2.  Press  0  on the Remote Commander.

3.  Press  ENTER  to read memory.

1.  Enter into Service Mode

2.  Press  2  or  5  on the remote to select the device item.

3.  Press  1  or  4  on the remote to select an item.

4.  Press  3  or  6  on the remote to change the data.

5.  Press  MUTING  then  ENTER  to write into memory.

 

Note:  Be careful when using the remote!  It will clear and re-initialize 
  

ALL NVM data including defl ection adjustment data if not reset 

  

properly as follows:

1.  Enter into Service Mode.

2.  Press  7 , then  MENU , and then press  ENTER  on the remote.

1.  Enter into Service Mode.

2.  Press  7 , then  9 , and then press  ENTER  on the remote.

1.  Enter into Service Mode.

2.  Press  8  and then press  ENTER  on the remote.

1.  After adjustment, pull out the plug from the AC outlet, then replace the 

plug in the AC outlet again.

2.  Turn the power switch ON and set to Service Mode.

3.  Call the adjusted items again to confi rm they were adjusted.

Use the Remote Commander (RM-Y184) to perform the circuit adjustments in this section.

Test Equipment Required:   1. Pattern generator   2. Frequency counter   3. Digital multimeter  4.  Audio oscillator

 # 1

µPD64082

IC3501 / BC-board

B8h (W) & B9h (R)  W&R: Write & Read

 # 2-1

IC3048 (Main) / B-board

9Ah

 # 2-2

IC3110 (Sub) / B-board

9Eh

 # 3-1

 # 3-2

 # 3-3

 # 3-4

 # 4-1

 # 4-2

 # 4-3

 # 5

CXA2151Q

IC3001 / B-board

84h

 # 6

CXA8070P

IC5513 / D-board

DEh

 # 7

CXA2026AS

IC5511 / D-board

8Eh

 # 8

BH3868FS

IC7001 / A-board

82h

 # 9

NJM2180M

IC4101 / S-board

2Eh

 Controlled through CXA1315M ( IC4103 / S-board / 48h )

 # 10

CXD9509AQ

IC3408 / B-board

2Eh

 Controlled through MID-XA Micro ( IC3090 / B-board / 64h )

 # 11

CXD9509AQ

IC3408 / B-board

2Eh

 Controlled through MID-XA Micro ( IC3090 / B-board / 64h )

 # 12

CXD9509AQ

IC3408 / B-board

2Eh

 Controlled through MID-XA Micro ( IC3090 / B-board / 64h )

 # 13

CXD9509AQ

IC3408 / B-board

2Eh

 Controlled through MID-XA Micro ( IC3090 / B-board / 64h )

 # 14

M306V2ME-153FP

IC701 / A-board

60h

 DX1A-2001 System Micro {V1.0}

µPD64082

IC3501 / BC-board

B8h (W) & B9h (R)

CXA2103Q

IC3048 (Main) / B-board

9Ah

CXA2150Q

IC201 / A-board

86h

 # 16

CXD2085M

IC3603 / B-board

40h

IC3602 (Main) / B-board

68h (Main)

IC3601 (Sub) / B-board

6Ch (Sub)

 # 18

M306V2ME-153FP

IC701 / A-board

60h

 DX1A-2001 System Micro {V1.0}

 # 19

M306V2ME-153FP

IC701 / A-board

60h

 DX1A-2001 System Micro {V1.0}

86h

CXA2150Q

IC201 / A-board

IC201 / A-board

CXP85840A-039Q

CXA2103Q

CXA2150Q

86h

 # 15

 # 17

 CCD&Vchip Micro (V2.14)

 MB94918RPF-G-137-BND (MASK), Software Version 12/08/00, IC3090/B-board (Slave Address: 64h)
 CXP85840A-039Q (MASK), Software Version 2.14, IC3602/B-board (Main/Slave Address: 68h) & IC3601/B-board (Sub/Slave Address: 

 M306V2ME-153FP (MASK), Software Version 1.0, IC701/A-board (Slave Adress: 60h)
The system micro name, software&patch versions, and the status of NVM devices are displayed only when in the service catergory 
(#19): ID.

0

NRMD  Operation mode setting

0~3

0

1

3

3

1

 Y-output correction
 (V-aperture compensation & Y-peaking filtering)

C

0~3

3

2

CLKS  System clock setting

C

0~3

1

3

NSDS  Selection for standard/non-standard signal processing

0~3

0

0

0

0

4

 Selection for inter-frame/inter-line processing

C

0~3

0

5

 Killer processing selection

C

0~3

1

6

 C-signal phase with respect to the Y-signal
 (Fine adjustment at 70 ns/step)

C

0~7

3

7

DYCO  DY detection coring level (Y motion detection coring)

0~15

2

2

2

2

8

DYGA  DY detection gain (Y motion detection gain) 

0~15

10

10

10

10

9

DCCO  DC detection coring level (C motion detection coring)

0~15

5

5

5

5

10 DCGA  DC detection gain (C motion detection gain) 

0~15

5

5

5

5

11 YNRL  Frame recersive YNR nonlinear filter limit level

C

0~3

1

12 CNRL  Frame recersive CNR nonlinear filter limit level

C

0~3

1

13 VTRH

 Hysteresis for Hsync non-standard signal detection
 (out-of-Hsync intra-field)

0~3

1

1

1

14 VTRR

 Sensitivity for Hsync non-standard signal detection
 (out-of-Hsync intra-field)

0~3

1

1

1

15 LDSR

 Sensitivity for frame non-standard signal detection
 (out-of-Hsync inter-frame)

0~3

2

2

2

16 VAPG  V-aperture compensation gai n

0~7

0

2

3

4

17

 V-aperture compensation convergence point

0~31

4

4

4

18

YPFT  Y peaking filter (BPF) center frequency

0~3

0

0

0

0

0

19 YPFG  Y peaking filter (BPF) gain

0~15

7

0

1

2

3

 CVideo (CV): CVideo1~4 inputs
 SVideo (SV):  SVideo1~3 inputs

 C: Common data

 Video1~4:  CVideo1~4 & SVideo1~3 inputs
 Video5&6: YPbPr-480i/480p/1080i inputs

This setting continues to

the next page.

8

 #16 VAPG (cont.)

0

0

0

0