Sony KV-38DRC2 Service Manual ▷ View online
— 38 —
KV-38DRC2 / 38DRC2C
SERVICE DATA LISTS
Control Register
Function & Link
Data
Type
Data
Range
Data Initial/Average Setting
(32V&36V CRTs)
Comment
0
SVOL Volume: Offset for Volume
0~3
0
1
SBAL Balance: Offset for Balance
0~(3)~7
7
( ): Settings at center
2
SBAS Bass: Offset for Bass
0~(3)~7
7
3
STRE Treble: Offset for Treble
0~(3)~7
7
4
BBLP BBE lowpass filter
0~15
0
5
BBHP BBE highpass filter
0~15
2
6
SREF Surround effect
0~7
11
7
AGC
Auto gain control
0, 1
0
8
BBE
BBE on/off
0, 1
1
Device Name: BH3868AFS { Audio Processor / ROHM } / IC7001 (A-board) / P/N: 8-759-678-92 (SBorSD#: NA)
Slave Address: 82h
Slave Address: 82h
Note:
The same AP service data is used for DX1A-2001&2000.
The same AP service data is used for DX1A-2001&2000.
Register
No & Name
DX1A-2001&2000 SERVICE LIST (#8):
Audio Processing (AP) / BH3868AFS
Control Register
Function & Link
Data
Type
Data
Range
Data Initial/Average Setting
(32V&36V CRTs)
Comment
0
TS
TruSurround effect selection
0~3
2
C: Common data
1
DMY1 Dummy data (No functions)
C
0~255
0
DMY1 is used to fulfil the minimum requirement of 2 control items in each service control
category.
category.
Device Name: NJM2180M { TruSurround 3D-Audio Processor / JRC } / IC4101 (S-board) / P/N: 8-759-686-15 (SB#: V9072)
Device Control: Controlled via CXA1315M (Audio Control D/A, IC4103/S-board, Slave Address: 48h) / P/N: 8-752-059-23 (SD#: S88Z45B)
Device Control: Controlled via CXA1315M (Audio Control D/A, IC4103/S-board, Slave Address: 48h) / P/N: 8-752-059-23 (SD#: S88Z45B)
Register
No & Name
Note:
The same TRUS service data is used for DX1A-2001&2000.
The same TRUS service data is used for DX1A-2001&2000.
DX1A-2001&2000 SERVICE LIST (#9):
TruSurround (TRUS) / NJM2180
— 39 —
KV-38DRC2 / 38DRC2C
SERVICE DATA LISTS
Control Register
Function & Link
Register Name
(Software)
Data
Type
Data
Range
Comment
0 DHPH Horizontal phase of the active display area d_h_phase
C
0~255
C: Common data
1 DVPH Vertical phase of the active display area
d_v_phase
C
0~63
2 DHAR Horizontal size of the active display area
d_h_area
C
0~255
3 DVAR Vertical size of the active display area
d_v_area
C
0~255
4 DHPW Horizontal pulse width
d_h_pwidth
C
0~63
5 DVPW Vertical pulse width
d_v_pwidth
C
0~7
6 DYCD Delay of YC signal output
d_yc_delay
C
0~63
7 DYSD Delay of YS signal output
d_ys_delay
C
0~7
Single
480i&p
Single
1080i
Favorite
8 MDHP Horizontal position of the main picture
m_dsp_hpos
0~255
12
9 MDVP Vertical position of the main picture
m_dsp_vpos
0~255
32
8
14
10 MDHS Horizontal size of the main picture
m_dsp_hsiz
0~255
158
11 MDVS Vertical size of the main picture
m_dsp_vsiz
0~255
120
135
106
12 MLHP (Horizontal position of the multi pictures)
0~255
13 MLVP (Vertical position of the multi pictures)
0~255
14 SDHP Horizontal position of the sub picture
s_dsp_hpos
0~255
15 SDVP Vertical position of the sub picture
s_dsp_vpos
0~255
16 SDHS Horizontal size of the sub picture
s_dsp_hsiz
0~255
17 SDVS Vertical size of the sub picture
s_dsp_vsiz
0~255
18 DPSW Switch of display output PLL
dsp_pll_sw
C
0, 1
0: MUST be used in DX1A-2001, 1: Used in DX1A-2000
19 MDL0 Model selection 0 (0: 16x9, 1: 4x3)
C
0, 1
Register
No & Name
33
MID Mode: Signle & Favorite
MID Mode: P&P & Favorite
MID Mode: All
(Single & P&P & Favorite)
91
20
20
0
41
MID Mode: Favorite
54
31
31
230
Data Initial/Average Setting
(32V/36V/40V CRTs)
172
MID Mode: All
(Single & P&P & Favorite)
0
240
135
135
27
14
61
61
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA)
Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) }
Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) }
DX1A-2001* SERVICE LIST (#10):
MID1 (Common Data)
MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Note:
* These MID1 settings are used for DX1A-2001 ONLY. The DPSW setting was changed from 1 in DX1A-2000 to 0 in DX1A-2001.
* These MID1 settings are used for DX1A-2001 ONLY. The DPSW setting was changed from 1 in DX1A-2000 to 0 in DX1A-2001.
7
2
1
2
1
— 40 —
KV-38DRC2 / 38DRC2C
SERVICE DATA LISTS
Control Register
Function & Link
Register Name
(Software)
Data
Type
Data
Range
YC
480i
YPbPr
480i
YC
480i
YPbPr
480i
YC
480i-(R)
YC
480i
YPbPr
480i
0
DRHP Horizontal position of the active display area (DRC-in) drc_hactv_pos
0~255
120
116
131
129
137
138
136
1
DRHS Hsize of the active display area (DRC-in)
drc_hactv_siz
0~255
174
174
167
167
168
165
165
2
DRVP Vposition of the active display area (DRC-in)
drc_vactv_pos
0~63
38
38
53
53
53
53
53
3
DRVS Vertical size of the active display area (DRC-in)
drc_vactv_siz
0~255
120
120
112
112
112
112
112
Register
No & Name
Data Initial/Average Setting
(32V&36V CRTs)
DX1A-2001&2000 SERVICE LIST (#11):
MID2 (DRC-in Data)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA)
Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) }
MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) }
MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
MID Mode: Single
MID Mode: P&P & Favorite
MID Mode: Freeze
Note:
The same MID2 service data is used for DX1A-2001&2000.
The same MID2 service data is used for DX1A-2001&2000.
Control Register
Function & Link
Register Name
(Software)
Data
Type
Data
Range
Comment
YPbPr
480P
Dummy
480i
0
VDHP Horizontal position of the active display area (VDO-in)
vdo_hactv_pos
0~255
122
179
1
VDHS Horizontal pixel size of the active display area (VDO-in) vdo_hactv_pos
0~255
159
199
2
VDVE Vertical even position of the active display area (VDO-in) vdo_vactv_evn
0~63
39
24
3
VDVS Vertical line size of the active display area (VDO-in)
vdo_vactv_pos
0~255
129
56
YC
480i
YPbPr
480P
YPbPr
1080i
Dummy
480i
4
VDVO Vertical odd position of the active display area (VDO-in) vdo_vactv_odd
0~3
0
0
0
0
5
VCPO Clamp pulse output timing (VDO-in)
vdo_clp_pos
0~255
95
70
40
90
6
VCWD Clamp pulse width (VDO-in)
vdo_clp_wdt
0~7
3
3
3
3
7
VYCD Analog input YC delay (VDO-in)
vdo_yc_delay
0~63
0
0
0
0
YPbPr
480P
YPbPr
1080i
8
VSTP
PD stop line count of external PLL (VDO-in)
vdo_pll_stop
0~255
119
160
9
VSTT
PD start line count of external PLL (VDO-in)
vdo_pll_strt
0~15
7
0
10
VHSC Horizontal sync cycle (VDO-in)
vdo_hsync_cyc
0~255
Note:
The same MID3 service data is used for DX1A-2001&2000.
The same MID3 service data is used for DX1A-2001&2000.
MID Mode: All
(Single & P&P & Favorite)
130
DX1A-2001&2000 SERVICE LIST (#12):
MID3 (VDO-in Data)
(Part-1/2)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA)
Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) }
Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) }
Data Initial/Average Setting
(32V&36V CRTs)
MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Register
No & Name
Dummy-480i settings are used
for No Signal cases.
for No Signal cases.
These settings continue to the
next page.
next page.
MID Mode: Single
— 41 —
KV-38DRC2 / 38DRC2C
SERVICE DATA LISTS
Register
No & Name
Comment
YC
480i
YPbPr
480P
YPbPr
1080i
Dummy
480i
YPbPr
480P
YPbPr
1080i
Dummy
480i
Dummy-480i settings are used for No Signal cases.
#0 VDHP (cont.)
197
127
91
179
131
98
179
#1 VDHS (cont.)
219
154
151
199
153
149
199
#2 VDVE (cont.)
24
53
37
24
53
37
24
#3 VDVS (cont.)
56
112
126
56
112
126
56
Data Initial Setting
(32V&36V CRTs)
MID Mode: FREEZE
Data Initial Setting
(32V&36V CRTs)
DX1A-2001&2000 SERVICE LIST (#12):
MID3 (VDO-in Data)
(Part-2/2)
Note:
The same MID3 service data is used for DX1A-2001&2000.
The same MID3 service data is used for DX1A-2001&2000.
MID Mode: P&P / Favorite
Control Register
Function & Link
Register Name
(Software)
Data
Type
Data
Range
Pro
Movie
Standard
Vivid
Pro
Movie
Standard
Vivid
0
POP
Selection of service data tables (Table #: 0~15)
0~15
0
1
2
3
4
5
6
7
1
MHLY Y coefficient code of Horizontal LPF (M)
m_hlpf_ycoef
0~3
1
1
1
1
1
1
1
1
2
MHLC C coefficient code of Horizontal LPF (M)
m_hlpf_ccoef
0~3
3
3
3
3
3
3
3
3
3
MVLY Y coefficient code of Vertical LPF (M)
m_vlpf_ycoef
0~3
0
0
0
0
0
0
0
0
4
MVLC C coefficient code of Vertical LPF (M)
m_vlpf_ccoef
0~3
0
0
0
0
0
0
0
0
5
MHYR Y coreing code of horizontal enhancement (M) m_henh_ycore
0~3
0
0
0
0
0
0
0
0
6
MHYL Y cliping code of horizontal enhancement (M) m_henh_yclip
0~3
1
1
1
1
1
1
1
1
7
MHYE Y level code of horizontal enhancement (M)
m_henh_yenh
0~7
4
0
0
0
3
0
0
0
8
MHYO Y coefficient code of horizontal enhancement (M m_henh_ycof
0, 1
1
1
1
1
1
1
1
1
9
MHCR C coreing code of horizontal enhancement (M) m_henh_ccore
0~3
0
0
0
0
0
0
0
0
10 MHCL C cliping code of horizontal enhancement (M) m_henh_cclip
0~3
1
1
1
1
1
1
1
1
11 MHCE C level code of horizontal enhancement (M)
m_henh_cenh
0~7
0
0
0
0
0
0
0
0
12 MHCO C coefficient code of horizontal enhancement (M m_henh_ccof
0, 1
1
1
1
1
1
1
1
1
13 MVYR Y coreing code of vertical enhancement (M)
m_venh_ycore
0~3
0
0
0
0
0
0
2
2
14 MVYL Y cliping code of vertical enhancement (M)
m_venh_yclip
0~3
1
1
1
1
1
1
1
1
15 MVYE Y level code of vertical enhancement (M)
m_venh_yenh
0~7
0
0
0
0
0
0
2
5
16 MVCR C coreing code of vertical enhancement (M)
m_venh_ccore
0~3
0
0
0
0
0
0
0
0
17 MVCL C cliping code of vertical enhancement (M)
m_venh_cclip
0~3
1
1
1
1
1
1
1
1
18 MVCE C level code of vertical enhancement (M)
m_venh_cenh
0~7
0
0
0
0
0
0
0
0
Settings for P&P (Main)
UHF/VHF & CVideo
YPbPr-480i (DVD)
Note:
The same MID5 service data is used for DX1A-2001&2000.
The same MID5 service data is used for DX1A-2001&2000.
See
the
next
page.
Register
No & Name
Data Initial/Average Setting
(32V&36V CRTs)
DX1A-2001&2000 SERVICE LIST (#13):
MID5 (Picture Data: MIDE)
(Part-1/4)
Device Name: CXD9509AQ { MID-XA / Fujitsu & SONY } / IC3408 (B-board) / P/N: 8-759-672-57 (SBorSD#: NA)
Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) }
Slave Address: 2Eh { Controlled through MID-XA Micro (IC3090/B-board, Slave Address: 64h) / P/N: 6-800-050-01 (SB#: V4216) }
Data Initial/Average Setting
(32V&36V CRTs)
MID-XA Micro (MASK type): MB94918RPF-G-137-BND, MID-XA Software: Version 12/08/00, (P/N: 6-800-050-01)
Click on the first or last page to see other KV-38DRC2 service manuals if exist.