Sony KDL-32SL130 / KDL-40SL130 Service Manual ▷ View online
25
KDL-32SL130/40SL130
KDL-32SL130/40SL130
KDL-32SL130 ONLY
1. Wire Dress Right Speaker wires and H4
cables in side clamp (white) and G3-Bd
bracket clip (black).
NOTE: H4-Bd/Rt. Speaker cables are dressed
UNDER AC Inlet.
2. Dress AC Inlet cables as shown.
Make sure Green/Yellow Earth Gnd. Is screwed
into lower LCD Bracket (w/4x8mm screw)
OPERATION PROCESS
NOTE: H4-Bd/Right Speaker cables
DRESSED INSIDE in plastic clip.
CLIP NOT ELIMNATED!!
DRESSED INSIDE in plastic clip.
CLIP NOT ELIMNATED!!
2
1
CAUTION:
DO NOT Push hard on AC
inlet wires after routing inside G1 bracket!!
Wire Insulation can be CUT by plastic edges!
Wire Insulation can be CUT by plastic edges!
NOTE Angle of Earth Gnd. Wire.
(Ring terminal touches "dimple" on plate)
(Ring terminal touches "dimple" on plate)
NOTE BOTH H4-Bd and Rt. Speaker cables
are dressed UNDER AC Inlet and in G-Brkt
clamp with AC Inlet Wires.
are dressed UNDER AC Inlet and in G-Brkt
clamp with AC Inlet Wires.
NOTE Wires NOT dressed in small clip on
G1-Bracket. (Too difficult to dress with
gloves over hands)
G1-Bracket. (Too difficult to dress with
gloves over hands)
H4 BOARD AND RIGHT SPEAKER (CONTINUED)
26
KDL-32SL130/40SL130
KDL-32SL130/40SL130
KDL-32SL130 ONLY
Route/Dress Harnesses connected to
Core Block as Shown
NOTE Order & Direction of Cables in
plastic Clip on Shield Case.
OPERATION PROCESS
2
3
1
1
Keep Cables BELOW level
of Shield Case (Pinch Points)
of Shield Case (Pinch Points)
NOTE order and direction of cables!
DRESS CABLES 1st
DRESS CABLES 2nd
DRESS CABLES 3rd
DRESS CABLES 4th
DRESS CABLES LAST
ON TOP ALL CABLES.
ON TOP ALL CABLES.
CORE BLOCK HARNESS
27
KDL-32SL130/40SL130
KDL-32SL130/40SL130
KDL-32SL130 ONLY
Route/Dress Core-Block cables as shown
Put Attention on DIRECTION of cables
in G-Bracket.
Put Attention on the position of the Sheet Core C
and routing of the Cables between Core Block
and G1-Bracket.
OPERATION PROCESS
NOTE direction of wires dressed in G-Bracket.
1
1
NOTE Routing of cables and position
of Sheet Core C.
of Sheet Core C.
CORE BLOCK HARNESS (CONTINUED)
28
KDL-32SL130/40SL130
KDL-32SL130/40SL130
KDL-32SL130 ONLY
Install/Wire Dress Harnesses as shown.
CAUTION: Make sure INVERTER CONN.
is Fully LOCKED!!
OPERATION PROCESS
1
2
CAUTION:
Make Sure Inverter
Connector is Fully LOCKED!
G1H-
Bd
NOTE: NEW G-Bracket Change!
Inverter wire is NOT dressed in 1st clip.
Inverter wires are dressed in cut-out on
side of the G-Bracket and the 2nd clip on right.
13P harness is NOT dressed in any of the
clips above PWB!
Inverter wires are dressed in cut-out on
side of the G-Bracket and the 2nd clip on right.
13P harness is NOT dressed in any of the
clips above PWB!
G1H BOARD
Click on the first or last page to see other KDL-32SL130 / KDL-40SL130 service manuals if exist.