Sony KDL-32SL130 / KDL-40SL130 Service Manual ▷ View online
13
KDL-32SL130/40SL130
KDL-32SL130/40SL130
1-3. STAND ASSEMBLY AND VESA ARM ASSEMBLY REMOVAL (KDL-32SL130 ONLY)
1-4. STAND ASSEMBLY AND VESA ARM ASSEMBLY REMOVAL (KDL-40SL130 ONLY)
1 Remove 2 screws from bottom of Arms, +PSW M5X16
2 Remove 3 screws from bottom bracket and Stand,
2 Remove 3 screws from bottom bracket and Stand,
+PSW M5X16
1 Remove 4 screws from bottom of Arms, +PSW M5X16
2 Remove 4 screws from bottom bracket and Stand, +PSW
2 Remove 4 screws from bottom bracket and Stand, +PSW
M5X16
1
VESA Arm Assembly
Under Cover
Stand Assembly
2
Bottom Bracket
1
VESA Arm Assembly
Under Cover
Stand Assembly
2
Bottom Bracket
14
KDL-32SL130/40SL130
KDL-32SL130/40SL130
1-5. U1 BOARD, SIDE TERMINAL AND SIDE JACK HOLDER REMOVAL
1-6. BU1 BOARD REMOVAL
1 Disconnect one connector
2 Remove one screw, +BVTP 3X12 TYPE2 IT-3
3 Release hooks and remove U1 Board.
4 Remove Side Terminal from Bezel.
5 Release hooks to remove Side Jack Holder from BU1 bottom
2 Remove one screw, +BVTP 3X12 TYPE2 IT-3
3 Release hooks and remove U1 Board.
4 Remove Side Terminal from Bezel.
5 Release hooks to remove Side Jack Holder from BU1 bottom
shield.
1 Remove 2 screws, +PSW M3X5
2 Remove 2 screws, HEX
3 Disconnect 5 connectors
4 Remove 7 screws, +BVST 3X8
5 Remove 5 screws, +PSW M3X5
2 Remove 2 screws, HEX
3 Disconnect 5 connectors
4 Remove 7 screws, +BVST 3X8
5 Remove 5 screws, +PSW M3X5
Side Jack Holder
1
2
4
5
3
Side Terminal
Wire Assembly
U1 Board
1
2
4
3
5
BU1 Top Shield
BU1 Board
BU1 Bottom Shield
15
KDL-32SL130/40SL130
KDL-32SL130/40SL130
1
2
3
5
4
Under Cover
Baffle Assembly
(KDL-40SL130 Only)
(KDL-40SL130 Only)
H4 Board
H3 Board
1-7. SPEAKER, H3 BOARD, AND H4 BOARD REMOVAL
1 Slide out Speaker and Baffl e from Bezel
2 Disconnect one connector
3 Release hooks and remove H3 Board
4 Disconnect one connector
5 Release hooks and remove H4 Board
2 Disconnect one connector
3 Release hooks and remove H3 Board
4 Disconnect one connector
5 Release hooks and remove H4 Board
1-8. G1H BOARD (POWER UNIT) AND G1 BRACKET REMOVAL (KDL-32SL130 ONLY)
1 Remove 4 screws, +PSW 3SG
2 Disconnect 3 connectors
2 Disconnect 3 connectors
1
2
Power Unit
G1 Bracket
16
KDL-32SL130/40SL130
KDL-32SL130/40SL130
1-9-1. REPLACING THE INVERTER CONNECTOR ASSEMBLY (KDL-40SL130 ONLY)
1
After inserting the connector
into the board, push the
middle section of the inverter
connector to confirm it
is securely connected.
into the board, push the
middle section of the inverter
connector to confirm it
is securely connected.
Push the right section of
the inverter connector and
confirm it is securely
connected.
the inverter connector and
confirm it is securely
connected.
Push the left section of
the inverter connector and
confirm it is securely
connected.
the inverter connector and
confirm it is securely
connected.
2
3
Use the following procedure to confirm that the Inverter connector is securely attached
to the board.
to the board.
1-9. G3 BOARD (POWER UNIT) AND D1 BOARD REMOVAL (KDL-40SL130 ONLY)
1 Disconnect 6 connectors
2 Remove 4 screws, +PSW 3SG
3 Disconnect 4 connectors
4 Remove 4 screws, +PSW 3SG
2 Remove 4 screws, +PSW 3SG
3 Disconnect 4 connectors
4 Remove 4 screws, +PSW 3SG
4
1
3
2
D1 Board
G3 Board
G3 Bracket
Click on the first or last page to see other KDL-32SL130 / KDL-40SL130 service manuals if exist.