Sony KD-30XS955 Service Manual ▷ View online
22
KD-30XS955/34XBR960/34XS955/36XS955
KD-30XS955/34XBR960/34XS955/36XS955
SPEAKER ASSY. WIRE DRESSING - RIGHT SPEAKERS (KD-34XBR960 ONLY)
Rev. 1
6/28/04
6/28/04
CRT
+
CLAMP
P/N: 4-857-472-01
4X16mm Screw
p/n: 7-685-663-99
TORQUE: 12kg-cm +-1
4X16mm Screw
p/n: 7-685-663-99
TORQUE: 12kg-cm +-1
!
+
HIMELON TAPE
P/N: 4-079-129-21
(2-PLACES)
(2-PLACES)
CLAMP
P/N: 4-857-472-01
4X16mm Screw
p/n: 7-685-663-99
TORQUE: 12kg-cm +-1
4X16mm Screw
p/n: 7-685-663-99
TORQUE: 12kg-cm +-1
Make sure tweeter
terminals are facing
AWAY from CRT!
terminals are facing
AWAY from CRT!
Hold Capacitor down with Himelon tape
(to prevent vibration and touching CRT
(to prevent vibration and touching CRT
Make sure Tweeter
leads do NOT touch
Beznet Rib (dashed
line)!!
Wires can Pinch when
Rear Cover is installed!
leads do NOT touch
Beznet Rib (dashed
line)!!
Wires can Pinch when
Rear Cover is installed!
!
WOOFER ASSY. WIRE DRESSING (KD-34XBR960 ONLY)
CRT Bracket
[A]
To FBT
CRT Bracket
Cable Tie
Rev. 1
6/28/04
6/28/04
DY
ANODE LEAD
Bundle slack
in Purselock.
in Purselock.
Purselock 4-072-499-01
(Install on Woofer Support Arm- Use
purselock hole on the LEFT side.)
23
KD-30XS955/34XBR960/34XS955/36XS955
KD-30XS955/34XBR960/34XS955/36XS955
CHASSIS DRESSING - HBZ BOARD AND USB (KD-34XBR960 ONLY)
1-900-808-02: 4P Conn Assy. w/RED housings
Dressed OUTSIDE 9mm black purselock
Dressed OUTSIDE 9mm black purselock
iLINK Cable (1-823-515-31) & 1-900-806-83: 11P Conn. Assy.
w/RED Taping. Dressed INSIDE 9mm black purselock.
w/RED Taping. Dressed INSIDE 9mm black purselock.
1-900-805-24 Double Ground Wire w/ferrite core
(p/n: 1-500-082-11)
NOTE: Tab on AZ-Bd (CN 519) is bent over in 45degree angle.
(p/n: 1-500-082-11)
NOTE: Tab on AZ-Bd (CN 519) is bent over in 45degree angle.
USB Cable (p/n:1-829-191-11) black cable routed in H-Bracket
clips.
clips.
iLINK Cable (1-823-515-31) w/ I Holder plastic clip on HBZ-Bd
(p/n: 4-082-405-01)
(p/n: 4-082-405-01)
1-900-805-24 dressed in H-bracket clips.
USB CABLE dressed in H-Bracket clips.
NOTE: Mounted tab on QH board is bent 45degrees.
NOTE Over-Molded Ferrite Position (important for EMI).
Also note ferrite core position (important for EMI).
CHASSIS DRESSING - QH BOARD (KD-34XBR960 ONLY)
24
KD-30XS955/34XBR960/34XS955/36XS955
KD-30XS955/34XBR960/34XS955/36XS955
CHASSIS DRESSING - WY AND CX CONNECTORS (KD-34XBR960 ONLY)
BOTH Connectors
Assys.
Connect to WY-BD
Assys.
Connect to WY-BD
p/n: 1-900-808-02
w/ RED housing
(WY-Bd to DL-BD)
w/ RED housing
(WY-Bd to DL-BD)
p/n: 1-900-808-32
6P Conn. Assy.
(BY-Bd to WY-BD)
6P Conn. Assy.
(BY-Bd to WY-BD)
11P Conn. Assy. w/Yellow Taping (p/n: 1-900-806-86) routed to CX-Bd.
This end of 1-900-806-86 connects to CX-Bd
NOTE: This Conn. Assy. Is routed INSIDE the 9mm black purselock.
NOTE: KNOT is only for picture. DO NOT knot
wires during actual dressing.
wires during actual dressing.
NOTE: 1-900-808-32, 6P Conn. Assy. Is routed INSIDE clamp (p/n: 4-857-472-01)
WIRE DRESSING - QBOX DRESSING (KD-34XBR960 ONLY)
25
KD-30XS955/34XBR960/34XS955/36XS955
KD-30XS955/34XBR960/34XS955/36XS955
WIRE DRESSING - QBOX DRESSING WITH CAUTIONS (KD-34XBR960 ONLY)
1-900-808-41 is dressed as far
BACK as possible
EMI Reasons
BACK as possible
EMI Reasons
11mm purselock. p/n:3-703-983-02
Qty=4
Qty=4
iLINK cable NOT dressed in this
purselock
purselock
Main bundle dressed low as
possible. EMI Reasons
possible. EMI Reasons
DO NOT let wires touch Cement
Resistor or heat sink
Resistor or heat sink
WIRE DRESSING - FERRITE ADDITIONS (KD-34XBR960 ONLY)
LOCATIONS OF FERRITE CORES
EFFECT EMI PERFORMANCE.
Please use caution when positioning ferrite cores!
EFFECT EMI PERFORMANCE.
Please use caution when positioning ferrite cores!
Click on the first or last page to see other KD-30XS955 service manuals if exist.