Sony VPL-VW85 Service Manual ▷ View online
1-31 (E)
VPL-VW85
Standard
Cinema1
Cinema1
Video
Standard
S Video
Standard
Input-A
Standard
Component
Standard
HDMI 1
Standard
Picture
HDMI 2
Standard
Cinema1
Cinema2
Cinema3
User
Cinema1
Cinema2
Cinema3
User
Picture
7.
8.
9.
10.
11.
12.
13.
14.
Memory
RCP
User3
User1
User2
User2
RCP Memory
FAN Memory
FAN Memory
IRIS Open
IRIS Close
IRIS Close
UF
Memory
LUT Memory
IRIS Open
IRIS Close
IRIS Close
UF
Memory
LUT Memory
No Memory
No Memory
Sub Micro Memory
Sub Micro Memory
Sub Micro Memory
Panel Alignment Memory
Panel Alignment Memory
Panel Alignment Memory
Gamma Memory
Gamma Memory
Dynamic
-2
-1
-1
0
1
2
3
1
2
3
Gamma
Memory
-3
Dynamic
Cinema2
Cinema3
User
Cinema3
User
Cinema1
Cinema2
Cinema3
User
Cinema2
Cinema3
User
Cinema1
Cinema2
Cinema3
User
Cinema2
Cinema3
User
Cinema1
Cinema2
Cinema3
User
Cinema2
Cinema3
User
Cinema1
Cinema2
Cinema3
User
Cinema2
Cinema3
User
Cinema1
Cinema2
Cinema3
User
Cinema2
Cinema3
User
Dynamic
Dynamic
Dynamic
Dynamic
Dynamic
Picture Memory
Memory
Memory
RCP
User3
User1
User2
User2
Memory
1-32 (E)
VPL-VW85
1-11.
Warning on Power Connection
Use a proper power cord for your local power supply.
The United
Continental
UK, Ireland, Australia,
Japan
China
States, Canada
Europe
New Zealand
Plug type
YP-3
YP-12A
*
YP-359
VM0722
Female end
YC-13
YC-13D
VM0303B
YC-13
VM0724
Cord type
SVT
H05VV-F
CEE (13) 53 rd (OC)
VCTF
227 IEC 53 (RVV)
Rated Voltage & Current
10A/125V
10A/250V
10A/250V
12A/125V
10A/250V
Safety approval
UL/CSA
VDE
VDE
DENANHO
CCC
* Use a rated plug that complies with the regulation of each country/region and the specifications.
2-1 (E)
VPL-VW85
Section 2
Electrical Adjustments
2-1. Preparations
2-1-1. Required Equipment
. Oscilloscope
Tektronix 2465 or equivalent
(bandwidth: 350 MHz or more)
(bandwidth: 350 MHz or more)
. NTSC, PAL, SECAM component signal generator
Tektronix TG2000 +AVG1 (optional module) +AWVG1
(optional module) or equivalent
(optional module) or equivalent
. VG (Programmable video signal generator)
VG849C or equivalent
. Digital voltmeter
Advantest TR6845 or equivalent
. Luminance meter
. Chrominance difference gauge
. Chrominance difference gauge
n
Perform the following adjustments at least 15 minutes after
turning on the power.
Perform the following adjustments at least 15 minutes after
turning on the power.
2-1-2. Service Mode Setting
1.
Set the “Status” to “On” in the “Setup” MENU.
2.
Close the menu by pressing “Menu” if its displayed.
3.
Press the buttons in the following order in 5 seconds:
“
“
”
→ “ ” → “ ” → “ ”
4.
The message “Do you wish to enter into the
SERVICE MODE? Yes No” will be displayed.
SERVICE MODE? Yes No” will be displayed.
5.
Select “Yes”.
m
. When leaving the SERVICE MODE, perform step 3.
. When leaving the SERVICE MODE, perform step 3.
“Do you wish to return to the USER MODE? Yes No”
will be displayed. Select “Yes”.
will be displayed. Select “Yes”.
. Before entering or exiting the SERVICE MODE, be sure
to select any input terminals other than HDMI1 and
HDMI2. Alternately, select the menus in the following
order: MENU/Function/Control for HDMI Setting/
Control for HDMI, and change the setup from ON to
OFF.
HDMI2. Alternately, select the menus in the following
order: MENU/Function/Control for HDMI Setting/
Control for HDMI, and change the setup from ON to
OFF.
. Note that when the items (W/B, Device Adjust) that can
be adjusted in the Service mode are adjusted and stored
in memory, they are saved in NVM and the factory
default data will be lost.
Be sure to perform “Save to memory” after entering and
exiting the Gamma adjustment mode. If the values are
changed in the Gamma adjustment mode and you want
to reset to the original value, turn off the power of the
unit and turn it on again. The UF data does not change
even if the mode for Advanced Iris in Cinema Black Pro
in Picture Adjust is changed without performing “Save
to memory”. When “Save to memory” is performed at
that time, the UF data of each Iris mode will be overwrit-
ten and lost.
in memory, they are saved in NVM and the factory
default data will be lost.
Be sure to perform “Save to memory” after entering and
exiting the Gamma adjustment mode. If the values are
changed in the Gamma adjustment mode and you want
to reset to the original value, turn off the power of the
unit and turn it on again. The UF data does not change
even if the mode for Advanced Iris in Cinema Black Pro
in Picture Adjust is changed without performing “Save
to memory”. When “Save to memory” is performed at
that time, the UF data of each Iris mode will be overwrit-
ten and lost.
2-2 (E)
VPL-VW85
2-1-3. Model Name Display (Shop
Demonstration) Mode Setting
1.
If the menu is being displayed, press the [MENU]
button to close the menu.
button to close the menu.
2.
Press the buttons within 5 seconds in the following
order:
“
order:
“
”
→ “ ” → “ ” → “ ”
Even if the message “Not applicable!” is displayed,
ignore it. If the key operations failed, wait for at least 6
seconds since the last key is pressed, and perform the
key operations again.
ignore it. If the key operations failed, wait for at least 6
seconds since the last key is pressed, and perform the
key operations again.
3.
“Which mode do you wish to display? Model Name
Display/Motionflow/Off” is displayed.
Display/Motionflow/Off” is displayed.
4.
Select “Model Name Display”.
m
. To exit the Model Name Display mode, perform step 2.
. To exit the Model Name Display mode, perform step 2.
“Which mode do you wish to display? Model Name
Display/Motionflow/Off” is displayed. Select “Off”.
Display/Motionflow/Off” is displayed. Select “Off”.
. Before entering or exiting the SERVICE MODE, be sure
to select any input terminals other than HDMI1 and
HDMI2. Alternately, select the menus in the following
order: MENU/Function/Control for HDMI Setting/
Control for HDMI, and change the setup from ON to
OFF.
HDMI2. Alternately, select the menus in the following
order: MENU/Function/Control for HDMI Setting/
Control for HDMI, and change the setup from ON to
OFF.
2-1-4. Motionflow (Shop Demonstration)
Mode Setting
1.
If the menu is being displayed, press the [MENU]
button to close the menu.
button to close the menu.
2.
Press the buttons within 5 seconds in the following
order:
“
order:
“
”
→ “ ” → “ ” → “ ”
Even if the message “Not applicable!” is displayed,
ignore it. If the key operations failed, wait for at least 6
seconds since the last key is pressed, and perform the
key operations again.
ignore it. If the key operations failed, wait for at least 6
seconds since the last key is pressed, and perform the
key operations again.
3.
“Which mode do you wish to display? Model Name
Display/Motionflow/Off” is displayed.
Display/Motionflow/Off” is displayed.
4.
Select “Motionflow”.
m
. To exit the Motionflow mode, perform step 2. “Which
. To exit the Motionflow mode, perform step 2. “Which
mode do you wish to display? Model Name Display/
Motionflow/Off” is displayed. Select “Off”.
Motionflow/Off” is displayed. Select “Off”.
. Before entering or exiting the SERVICE MODE, be sure
to select any input terminals other than HDMI1 and
HDMI2. Alternately, select the menus in the following
order: MENU/Function/Control for HDMI Setting/
Control for HDMI, and change the setup from ON to
OFF.
HDMI2. Alternately, select the menus in the following
order: MENU/Function/Control for HDMI Setting/
Control for HDMI, and change the setup from ON to
OFF.
Click on the first or last page to see other VPL-VW85 service manuals if exist.